Bear 650 Exhaust

Control Your Exhaust. On Your Terms. Your valved exhaust has two modes — you just haven't been able to use both. The Valvetronic Exhaust Valve Control Module (Manual) gives you a handlebar-mounted switch that physically opens or closes the exhaust butterfly valve whenever you want. Full roar on the open highway. Clean and quiet through the colony, toll booth, or early morning streets. No apps. No wiring. No compromise. This is the most reliable way to control a valved exhaust — because there's nothing electronic to fail. A cable connects your thumb to the valve. That's it. What This Module Does Valved exhausts come with an internal butterfly valve that changes how exhaust gases flow. When the valve is closed, gases pass through a baffled internal route — quieter, more refined. When the valve is open, gases take the free-flow path — louder, rawer, with a more aggressive exhaust note. Most valved exhausts ship without any control module. The valve stays fixed in one position. This module gives you a switch to change it, whenever you want, from the handlebar. Closed valve: Quiet, compliant, neighbour-friendly. Use it in residential areas, at idle, in traffic, on early morning rides. Open valve: The sound your exhaust was built to make. Use it on highways, open roads, or anywhere you want the full character of your exhaust to come through. Why Manual Over Electric Zero electronics. No solenoid, no servo, no wiring loom, no relay. Nothing to short, corrode, or fail over time. Works anywhere, always. The valve opens when you pull the cable. No power required. No sensor needed. Doesn't care if your bike is warm, cold, or idling. You're in control. The valve is exactly where you put it — open or closed — until you choose to change it. No automatic switching when you don't want it. Simple to install. Route the cable, connect to the valve actuator, mount the switch. No ECU tapping, no wiring diagrams, no calibration. Built to last. A cable and a switch outlast any electronic actuator on a motorcycle. Less to maintain, less to replace. How It Works A control switch mounts on your handlebar. A cable runs from the switch down to the butterfly valve actuator on your exhaust. When you flick the switch, cable tension physically rotates the valve between open and closed. The entire system is mechanical — no power draw from your bike's electrical system, no ECU communication, no mapping required. Installation requires routing the cable cleanly along the frame to the exhaust, connecting to the existing valve actuator arm, and adjusting cable tension for full travel in both directions. A standard workshop should be able to install this in under an hour on most platforms. Compatible Bikes This is a universal module — it works with any valved exhaust system that supports mechanical cable actuation, regardless of bike brand or model. Below is a verified compatibility reference across popular Indian market platforms. If your bike has a valved slip-on, this module can control it. Royal Enfield Interceptor 650 / Continental GT 650 / Classic 650 / Bear 650 Classic 350 (Reborn) / Hunter 350 / Meteor 350 Himalayan 411 / Himalayan 450 / Guerrilla 450 Scram 411 / Super Meteor 650 / Shotgun 650 KTM Duke 125 / Duke 200 / Duke 250 / Duke 390 RC 125 / RC 200 / RC 390 Adventure 250 / Adventure 390 / Adventure 390 (2025) 790 Adventure Triumph Speed 400 / Scrambler 400 X / Tiger 400 Street Triple 675 / Speed T4 Bonneville T100 / T120 / Street Twin Tiger 800 / Street Scrambler 900 Yamaha MT-15 V2 / R15 V3 / R15 V4 FZ25 / FZS25 / Fazer 25 MT-03 / R3 YZF-R1 / YZF-R6 / MT-07 Kawasaki Ninja 400 / Ninja 650 / Ninja 1000 SX Z800 / Z900 / Z900 (2026) Versys 650 / Versys-X 300 / Versys 1000 Honda CB200X / CB350 Highness / CB350RS CBR 250R / CB300R / CB300F CBR 650R / CBR 650F / CB Hornet 160R Africa Twin / NX200 Bajaj Pulsar NS200 / RS200 / AS200 / 220F Dominar 250 / Dominar 400 NS 400Z TVS Apache RR 310 / Apache RTR 200 4V Ronin BMW G 310 R / G 310 GS / G 310 RR S 1000 R / S 1000 XR / R 1000 GS Suzuki Gixxer 250 / V-Strom 250SX / V-Strom 650 GSX-R750 / GSX-S750 / GSX-R1000 Hayabusa (2021 Onwards) Ducati Scrambler 800 / Scrambler 1100 Monster 797 / Monster 1200 Hypermotard 939 / Multistrada 950 Streetfighter V4 Harley Davidson Street 750 / Street Rod X440 / X440T Forty Eight / Iron 883 Jawa / Yezdi Jawa 42 FJ / Jawa Perak Yezdi Adventure / Yezdi Roadster Hero Karizma XMR / Xpulse 200 4V / Xpulse 210 Benelli TRK 502 / TRK 502X / TNT 600i / TNT 899 This module is universal — it controls the valve mechanism, not the exhaust itself. Your exhaust must have a butterfly valve with a mechanical actuator arm. Confirm exhaust compatibility before ordering. If your bike model isn't listed but runs a valved slip-on, this module will work. What's in the Box 1 × Valvetronic Manual Control Switch (handlebar mount) 1 × Control cable assembly Mounting hardware Exhaust system not included. Module requires a compatible valved exhaust to function. Specifications Control Type: Manual (mechanical cable) Actuation: Direct cable-pull butterfly valve operation Power Required: None ECU / Wiring Integration: Not required Valve Positions: Open / Closed (user-operated) Mount: Handlebar switch with cable routing Fitment: Universal — compatible with mechanically-actuated valved exhausts Brand: Valvetronic MRP: ₹3,499 Also Available Want automatic valve switching based on RPM and throttle input? The Valvetronic Electric (Automatic) Module does exactly that — the valve opens and closes on its own as you ride. View the Electric Module →

Read more less

Built for the Bear 650 Twin Engine The Barrel B-20 Bass Master Exhaust is engineered specifically for the Royal Enfield Bear 650 platform. This is not just a slip-on—it’s a performance-focused system with a decat pipe designed to unlock the full breathing potential of the 650 twin engine. 🔊 Signature Bass Master Sound Deep, bass-heavy exhaust tone Strong low-frequency thump No sharp or raspy noise This is tuned for authority, not noise pollution. ⚙️ Decat Performance Advantage Unlike standard slip-ons, this setup includes a decat pipe: Frees up exhaust flow Reduces back pressure Improves engine breathing Enhances throttle response Result → smoother, more responsive acceleration ⚡ Performance Gains You Can Feel Noticeably sharper throttle response Improved torque delivery More engaging riding experience No unnecessary tuning complexity—just real-world gains. 🪶 Weight Reduction & Build Quality Saves approx 1.5–5.5 kg vs stock Constructed from 304 Stainless Steel High durability + corrosion resistance 🛠️ Plug & Play Fitment Direct bolt-on installation (OEM mounts) No cutting or welding required Installation time: ~30–45 minutes 🔧 DB Killer Control Comes with removable DB killer Tune sound based on preference: With DB killer → controlled Without → full bass roar 📦 What’s in the Box B-20 Bass Master Exhaust Decat Pipe DB Killer Mounting Hardware ✅ Compatibility Royal Enfield Bear 650 ⚠️ Important Notes This is a performance exhaust with decat pipe May not comply with emission or noise regulations in all regions ECU remap is not mandatory, but can help extract optimal performance Sound output will be significantly louder than stock 🛡️ Warranty Manufacturer Warranty: Lifetime rust warranty 1-year weld warranty RawTorque Note:RawTorque does not provide any additional warranty beyond the manufacturer’s coverage.For more details, please refer to our warranty policy.

Read more less

Powerage Slip-On Exhaust with De-Cat Pipe for Royal Enfield Bear 650 – OE & Cone Type Upgrade your Royal Enfield Bear 650 with the Powerage Slip-On Exhaust System featuring a performance-focused de-cat pipe setup engineered for improved exhaust flow, reduced weight, deeper exhaust note, and enhanced throttle response. Manufactured entirely from premium 304 Stainless Steel, the Powerage exhaust system is dyno-tested and designed to deliver a balance of usable performance and refined sound without compromising daily rideability. This exhaust setup is available in two muffler variants: OE Type – Factory-inspired premium styling Cone Type – Sportier tapered exhaust profile Both variants include the de-cat pipe and removable dB killer, giving riders the flexibility to tune the exhaust note according to riding preference. The system significantly reduces overall exhaust weight compared to the stock setup while improving engine breathing efficiency and delivering a richer, deeper exhaust tone. Available Variants OE Type OEM-inspired exhaust styling Cleaner factory-style appearance Ideal for subtle premium builds Cone Type Sportier aggressive exhaust design Sleeker tapered muffler profile Ideal for performance-inspired builds Key Features Designed specifically for Royal Enfield Bear 650 Full 304 stainless steel construction Includes performance de-cat pipe Dyno-tested configuration Removable dB killer included Improved exhaust flow efficiency Deeper bass-heavy exhaust note Weight reduction over stock exhaust Bolt-on fitment No ECU remap mandatory for installation Lifetime warranty against rust & manufacturing defects Performance Benefits Sharper throttle response Reduced overall exhaust weight Improved engine breathing Enhanced exhaust sound character Better heat resistance compared to mild steel systems Freer exhaust flow for smoother power delivery Technical Specifications Brand : Powerage Product Type : Slip-On Exhaust System Compatibility : Royal Enfield Bear 650 Material : 304 Stainless Steel Exhaust Type : Slip-On with De-Cat Pipe Muffler Variants : OE Type / Cone Type dB Killer : Included, Removable Finish : Stainless Steel / Matte Black depending on variant Installation Type : Bolt-On Dyno Tested : Yes Weight Information Slip-On Weight : 2.5 kg De-Cat Pipe Weight : 0.7 kg Stock OE Exhaust Weight : Approx. 6.5 kg Claimed Power Gain : Up to +2.5 bhp Important Note Please select the correct exhaust variant before placing your order. This listing is compatible only with Royal Enfield Bear 650. Professional installation is recommended for best fitment and alignment. Exhaust sound may vary depending on tuning and riding conditions. Package Contents 1 x Powerage Slip-On Exhaust 1 x De-Cat Pipe Mounting Hardware Clamps & Fasteners Removable dB Killer

Read more less

Red Rooster Stellar X Performance Exhaust for Royal Enfield Bear 650 The Red Rooster Stellar X Performance Exhaust is a motorcycle exhaust system developed specifically for the Royal Enfield Bear 650. It is designed for riders looking to upgrade the stock exhaust with a deeper and more engaging exhaust note while retaining controlled sound levels suitable for daily riding and long-distance touring. The Stellar X is positioned as a balanced performance exhaust rather than an extreme loud setup. It focuses on improving the riding experience through sound character, weight reduction, and efficient exhaust flow without compromising usability for regular road use. Design and Construction The Red Rooster Stellar X exhaust is manufactured using SS304 stainless steel, chosen for its strength, corrosion resistance, and thermal stability under sustained riding conditions. Stainless steel construction helps the exhaust withstand heat cycles and environmental exposure over time, making it suitable for both urban riding and extended highway use. The exhaust design prioritizes structural integrity while keeping overall weight lower than the stock exhaust system. Reduced weight contributes to improved handling feel and easier maneuverability, especially during city riding and low-speed conditions. Performance Characteristics The Stellar X exhaust is engineered to support freer engine breathing compared to the stock exhaust. By reducing exhaust restriction, it supports smoother exhaust flow, which can contribute to improved throttle response during acceleration and roll-on riding scenarios. Rather than focusing on maximum loudness, Red Rooster positions the Stellar X as an exhaust that delivers a deeper and more aggressive exhaust tone while maintaining sound levels that remain practical for everyday use. This makes it suitable for riders who want a noticeable sound upgrade without excessive noise fatigue on longer rides. No ECU remapping or engine modifications are stated as required by the manufacturer for installation or operation. Fitment and Installation The Red Rooster Stellar X Performance Exhaust is supplied as a bolt-on replacement for the Royal Enfield Bear 650. It is designed to mount directly onto the motorcycle using existing mounting points, without the need for permanent modifications to the bike. Installation does not require cutting, welding, or alteration of the motorcycle frame. Fitment compatibility is specific to the Bear 650, and proper installation ensures correct alignment and secure mounting. Professional installation is recommended to ensure proper fitment and to avoid exhaust leaks or alignment issues. Riding Usage This exhaust system is suited for: Daily city commuting Highway riding Long-distance touring Its balanced sound profile and stainless steel construction make it suitable for riders who want a functional upgrade that integrates well with regular riding conditions rather than track-only use. Finish Options The Red Rooster Stellar X exhaust is offered in multiple finish options, which can be selected as variants during purchase. Finish availability may vary depending on stock and manufacturer supply. What’s Included 1 x Red Rooster Stellar X Performance Exhaust for Royal Enfield Bear 650 Required mounting components as supplied by the manufacturer Important Notes Designed specifically for Royal Enfield Bear 650 This is a performance exhaust system, not a cosmetic slip-on only No ECU remapping or engine changes are stated as required by the manufacturer Installation quality directly affects performance and sound output Summary The Red Rooster Stellar X Performance Exhaust for Royal Enfield Bear 650 is a well-balanced exhaust upgrade designed for riders who want improved sound character, reduced weight, and practical performance benefits without sacrificing everyday usability. Built using SS304 stainless steel and supplied as a direct bolt-on system, it offers a clean and reliable upgrade path for Bear 650 owners.Usage and Maintenance The Red Rooster Stellar X Performance Exhaust for Royal Enfield Bear 650 is intended for regular road use under normal riding conditions. Periodic inspection of mounting points and fasteners is recommended to ensure secure fitment over time. Exhaust sound and performance characteristics may vary depending on riding style and operating conditions.

Read more less