Jawa & Yezdi Motorcycle Accessories

NGK Iridium IX. A 0.6mm fine-wire iridium centre electrode in place of a conventional one, firing a sharper, more focused spark. That gives crisper throttle response, easier cold starts and more consistent ignition, held steady by an electrode that barely erodes. Direct fit. Nothing to adjust. Before you order Choose the variant that matches your bike. NGK specifies different plugs across the Yamaha range depending on model and year: the YZF-R15, R15 2.0 and R3 are listed for the CR8EIX, and the R15 V3, V4 and MT-15 take a different plug again. Message us with your model and year before ordering and we will confirm the exact part. We would rather spend a minute on that than have you fit the wrong plug. Specifications Part number · CR8EIX Stock number - 4218 Type · Iridium IX, 0.6mm fine-tip iridium centre electrode Heat range · 8 · Spark gap: 0.8 mm Thread diameter - 10 mm Thread length - 19 mm Hex size - 16 mm Fitting Arrives pre-gapped and ready to fit. Thread in by hand first, then torque to your manual's figure. If you check the gap, move the outer electrode only.

Read more less

NGage B8RII-8 Double Iridium Spark Plug for Jawa & Yezdi Motorcycles (BS4 / BS6 Compatible) The NGage B8RII-8 Double Iridium Spark Plug is a precision ignition component developed for select Jawa and Yezdi motorcycles built on modern, fuel-injected single-cylinder platforms. Manufactured in Japan, this spark plug is part of NGage’s Double Iridium series and is specified for use in both BS4 and BS6 compliant motorcycles, as stated by the manufacturer. This listing focuses exclusively on its application for the Jawa and Yezdi models listed in NGage’s official compatibility chart for part number B8RII-8. It is intended as a direct replacement spark plug for these motorcycles, without modification. Designed for Jawa & Yezdi Motorcycles NGage specifies the B8RII-8 spark plug for a defined group of Jawa and Yezdi motorcycles that share common ignition system requirements. The following models are listed by NGage for use with the B8RII-8 spark plug: Jawa Jawa Forty Two Jawa Bobber 42 Jawa 350 Jawa 42 FJ Yezdi Yezdi Roadster Yezdi Adventure Yezdi Scrambler These motorcycles represent modern, liquid-cooled and air-cooled single-cylinder platforms developed for contemporary combustion and emission standards. NGage lists the same B8RII-8 specification across all of these models, indicating alignment with their ignition system design and operating parameters. For these motorcycles, the B8RII-8 is intended to function as a like-for-like replacement for the factory-specified spark plug type. It is not positioned as a tuning component or a modification-driven upgrade, but as a specification-correct ignition part for routine service or replacement. Double Iridium Spark Plug Construction NGage classifies the B8RII-8 as a Double Iridium spark plug, meaning iridium material is used on both the center electrode and the ground electrode. Iridium is used in modern spark plug construction due to its high melting point and resistance to electrode erosion during repeated ignition cycles. This construction approach is commonly applied in motorcycles with high-energy ignition systems and tightly controlled combustion environments. The double-iridium configuration is intended to maintain consistent electrode geometry over extended operating periods under normal riding conditions. NGage does not publish electrode dimensions, spark-gap values, heat-range explanations, or service-interval figures for this model. BS4 and BS6 Compatibility NGage specifies that the B8RII-8 spark plug is compatible with both BS4 and BS6 vehicles. This makes it suitable for use across production years that fall before and after the BS6 emission-standard transition, provided the motorcycle is included in the compatibility list. For the Jawa and Yezdi motorcycles listed above, this ensures suitability across emission-compliant variants without requiring a change in spark plug specification. No emission-reduction, fuel-efficiency, or tuning claims are made for this product. Manufacturing Origin The B8RII-8 spark plug is manufactured in Japan, as stated by NGage. NGage does not publish further information regarding production processes, certifications, or testing standards for this model. The country of manufacture is provided here as factual product information only. Intended Use The NGage B8RII-8 is intended for routine replacement during scheduled maintenance or spark-plug service intervals recommended by the motorcycle manufacturer. It is suitable for everyday road use on the Jawa and Yezdi motorcycles listed below within standard operating conditions. This spark plug is not positioned by NGage as a racing-only, track-specific, or specialized tuning component. Fitment Accuracy Correct spark plug selection is critical for engine operation and long-term reliability. The B8RII-8 should be installed only on motorcycles listed in the compatibility section below. Use on non-listed motorcycles is not recommended. Compatibility As per NGage official compatibility chart for part number B8RII-8: Jawa Motorcycles Jawa Forty Two Jawa Bobber 42 Jawa 350 Jawa 42 FJ Yezdi Motorcycles Yezdi Roadster Yezdi Adventure Yezdi Scrambler Variant Explanation This listing is for NGage B8RII-8 Double Iridium Spark Plug only. “Double Iridium” refers to iridium usage on both the center and ground electrodes. This part number represents a single manufacturer-defined specification. No alternate heat ranges or material variants are included in this listing. Specifications  Brand: NGage Part Number: B8RII-8 Spark Plug Type: Double Iridium Vehicle Compatibility: BS4 & BS6 Country of Manufacture: Japan Application: Motorcycle spark plug Installation / Usage Notes Install only on Jawa and Yezdi motorcycles listed in the compatibility section. Follow the motorcycle manufacturer’s service-manual torque specifications and standard spark-plug installation procedure. Install on a cold engine. Terminal Nut NGage supplies this plug with a bare threaded terminal stud, and no terminal nut fitted. On Yezdi orders we fit a brass screw-on terminal nut before dispatch, at no extra cost. Jawa orders ship as supplied, on the bare stud. If you are not sure which your bike takes, leave your exact model in the order notes and we will check it before packing.

Read more less

Control Your Exhaust. On Your Terms. Your valved exhaust has two modes, you just haven't been able to use both. The Valvetronic Exhaust Valve Control Module (Manual) gives you a handlebar-mounted switch that physically opens or closes the exhaust butterfly valve whenever you want. Full roar on the open highway. Clean and quiet through the colony, toll booth, or early morning streets. No apps. No wiring. No compromise. This is the most reliable way to control a valved exhaust, because there's nothing electronic to fail. A cable connects your thumb to the valve. That's it. What This Module Does Valved exhausts come with an internal butterfly valve that changes how exhaust gases flow. When the valve is closed, gases pass through a baffled internal route, quieter, more refined. When the valve is open, gases take the free-flow path, louder, rawer, with a more aggressive exhaust note. Most valved exhausts ship without any control module. The valve stays fixed in one position. This module gives you a switch to change it, whenever you want, from the handlebar. Closed valve: Quiet, compliant, neighbour-friendly. Use it in residential areas, at idle, in traffic, on early morning rides. Open valve: The sound your exhaust was built to make. Use it on highways, open roads, or anywhere you want the full character of your exhaust to come through. Why Manual Over Electric Zero electronics. No solenoid, no servo, no wiring loom, no relay. Nothing to short, corrode, or fail over time. Works anywhere, always. The valve opens when you pull the cable. No power required. No sensor needed. Doesn't care if your bike is warm, cold, or idling. You're in control. The valve is exactly where you put it, open or closed, until you choose to change it. No automatic switching when you don't want it. Simple to install. Route the cable, connect to the valve actuator, mount the switch. No ECU tapping, no wiring diagrams, no calibration. Built to last. A cable and a switch outlast any electronic actuator on a motorcycle. Less to maintain, less to replace. How It Works A control switch mounts on your handlebar. A cable runs from the switch down to the butterfly valve actuator on your exhaust. When you flick the switch, cable tension physically rotates the valve between open and closed. The entire system is mechanical, no power draw from your bike's electrical system, no ECU communication, no mapping required. Installation requires routing the cable cleanly along the frame to the exhaust, connecting to the existing valve actuator arm, and adjusting cable tension for full travel in both directions. A standard workshop should be able to install this in under an hour on most platforms. Compatible Bikes This is a universal module: it works with any valved exhaust system that supports mechanical cable actuation, regardless of bike brand or model. Below is a verified compatibility reference across popular Indian market platforms. If your bike has a valved slip-on, this module can control it. Royal Enfield Interceptor 650 / Continental GT 650 / Classic 650 / Bear 650 Classic 350 (Reborn) / Hunter 350 / Meteor 350 Himalayan 411 / Himalayan 450 / Guerrilla 450 Scram 411 / Super Meteor 650 / Shotgun 650 KTM Duke 125 / Duke 200 / Duke 250 / Duke 390 RC 125 / RC 200 / RC 390 Adventure 250 / Adventure 390 / Adventure 390 (2025) 790 Adventure Triumph Speed 400 / Scrambler 400 X / Tiger 400 Street Triple 675 / Speed T4 Bonneville T100 / T120 / Street Twin Tiger 800 / Street Scrambler 900 Yamaha MT-15 V2 / R15 V3 / R15 V4 FZ25 / FZS25 / Fazer 25 MT-03 / R3 YZF-R1 / YZF-R6 / MT-07 Kawasaki Ninja 400 / Ninja 650 / Ninja 1000 SX Z800 / Z900 / Z900 (2026) Versys 650 / Versys-X 300 / Versys 1000 Honda CB200X / CB350 Highness / CB350RS CBR 250R / CB300R / CB300F CBR 650R / CBR 650F / CB Hornet 160R Africa Twin / NX200 Bajaj Pulsar NS200 / RS200 / AS200 / 220F Dominar 250 / Dominar 400 NS 400Z TVS Apache RR 310 / Apache RTR 200 4V Ronin BMW G 310 R / G 310 GS / G 310 RR S 1000 R / S 1000 XR / R 1000 GS Suzuki Gixxer 250 / V-Strom 250SX / V-Strom 650 GSX-R750 / GSX-S750 / GSX-R1000 Hayabusa (2021 Onwards) Ducati Scrambler 800 / Scrambler 1100 Monster 797 / Monster 1200 Hypermotard 939 / Multistrada 950 Streetfighter V4 Harley Davidson Street 750 / Street Rod X440 / X440T Forty Eight / Iron 883 Jawa / Yezdi Jawa 42 FJ / Jawa Perak Yezdi Adventure / Yezdi Roadster Hero Karizma XMR / Xpulse 200 4V / Xpulse 210 Benelli TRK 502 / TRK 502X / TNT 600i / TNT 899 This module is universal, it controls the valve mechanism, not the exhaust itself. Your exhaust must have a butterfly valve with a mechanical actuator arm. Confirm exhaust compatibility before ordering. If your bike model isn't listed but runs a valved slip-on, this module will work. What's in the Box 1 × Valvetronic Manual Control Switch (handlebar mount) 1 × Control cable assembly Mounting hardware Exhaust system not included. Module requires a compatible valved exhaust to function. Specifications Control Type: Manual (mechanical cable) Actuation: Direct cable-pull butterfly valve operation Power Required: None ECU / Wiring Integration: Not required Valve Positions: Open / Closed (user-operated) Mount: Handlebar switch with cable routing Fitment: Universal, compatible with mechanically-actuated valved exhausts Brand: Valvetronic MRP: ₹3,499 Also Available Want automatic valve switching based on RPM and throttle input? The Valvetronic Electric (Automatic) Module does exactly that, the valve opens and closes on its own as you ride. View the Electric Module →

Read more less

Your Exhaust. Intelligent. Automatic. The Valvetronic Electric (Automatic) Exhaust Valve Control Module brings smart valve control to your valved exhaust. The butterfly valve opens and closes automatically, no switches to flip, no cables to pull. It reads riding input and actuates the valve on its own, giving you the quiet mode when you need it and the full exhaust character when you're pushing hard. This is the premium way to run a valved exhaust. Set it and forget it. The system handles the rest. What This Module Does Valved exhausts have an internal butterfly valve that controls exhaust gas routing. Valve closed = exhaust gases take a baffled internal path, quieter, more refined note. Valve open = free-flow path, the full aggressive exhaust character your slip-on was built for. The Electric Module automates this. A solenoid or servo actuator connects to the butterfly valve. The control unit reads signals from your bike, RPM, throttle position, or a dedicated switch, and commands the valve to open or close accordingly. You get intelligent mode switching without any manual input mid-ride. Low RPM / idle / city: Valve stays closed. Quiet, controlled, compliant. Use it on early morning starts, residential areas, toll plazas, traffic jams. Higher RPM / open throttle / highway: Valve opens automatically. The exhaust opens up, the note deepens, and you get the full sound profile of your slip-on exhaust. Why Electric Over Manual Fully automatic operation. The valve transitions without any rider input. Focus on riding, the module handles valve control in the background. Seamless transitions. No fumbling with a switch mid-corner or on a highway run. The valve opens and closes at the right moment, every time. Consistent behaviour. Same switching point every ride. No forgetting to open the valve before a run or close it before entering the city. Optional override. Most configurations allow a dedicated switch for manual override if you want direct control in specific situations. Premium install. Cleaner setup than a cable system, no handlebar clutter, no cable routing along the frame. How It Works The control unit connects to your bike's wiring, typically tapping into the ignition circuit, RPM signal, or a dedicated output. When the defined threshold is crossed (RPM, throttle position, or switch activation), the unit sends a signal to an electric actuator mounted on the exhaust valve. The actuator rotates the butterfly valve between open and closed positions in milliseconds. The system draws minimal current from the battery and does not require ECU remapping, fuel map changes, or custom tuning. Installation involves wiring the control unit to the correct signal source and mounting the actuator to the exhaust valve arm. A professional auto electrician or experienced mechanic can complete the installation cleanly on most bikes in 1-2 hours. Compatible Bikes This is a universal module: it works with any valved exhaust system that supports electric or solenoid actuation, regardless of bike brand or model. Below is a verified compatibility reference across popular Indian market platforms. If your bike has a valved slip-on, this module can control it. Royal Enfield Interceptor 650 / Continental GT 650 / Classic 650 / Bear 650 Classic 350 (Reborn) / Hunter 350 / Meteor 350 Himalayan 411 / Himalayan 450 / Guerrilla 450 Scram 411 / Super Meteor 650 / Shotgun 650 KTM Duke 125 / Duke 200 / Duke 250 / Duke 390 RC 125 / RC 200 / RC 390 Adventure 250 / Adventure 390 / Adventure 390 (2025) 790 Adventure Triumph Speed 400 / Scrambler 400 X / Tiger 400 Street Triple 675 / Speed T4 Bonneville T100 / T120 / Street Twin Tiger 800 / Street Scrambler 900 Yamaha MT-15 V2 / R15 V3 / R15 V4 FZ25 / FZS25 / Fazer 25 MT-03 / R3 YZF-R1 / YZF-R6 / MT-07 Kawasaki Ninja 400 / Ninja 650 / Ninja 1000 SX Z800 / Z900 / Z900 (2026) Versys 650 / Versys-X 300 / Versys 1000 Honda CB200X / CB350 Highness / CB350RS CBR 250R / CB300R / CB300F CBR 650R / CBR 650F / CB Hornet 160R Africa Twin / NX200 Bajaj Pulsar NS200 / RS200 / AS200 / 220F Dominar 250 / Dominar 400 NS 400Z TVS Apache RR 310 / Apache RTR 200 4V Ronin BMW G 310 R / G 310 GS / G 310 RR S 1000 R / S 1000 XR / R 1000 GS Suzuki Gixxer 250 / V-Strom 250SX / V-Strom 650 GSX-R750 / GSX-S750 / GSX-R1000 Hayabusa (2021 Onwards) Ducati Scrambler 800 / Scrambler 1100 Monster 797 / Monster 1200 Hypermotard 939 / Multistrada 950 Streetfighter V4 Harley Davidson Street 750 / Street Rod X440 / X440T Forty Eight / Iron 883 Jawa / Yezdi Jawa 42 FJ / Jawa Perak Yezdi Adventure / Yezdi Roadster Hero Karizma XMR / Xpulse 200 4V / Xpulse 210 Benelli TRK 502 / TRK 502X / TNT 600i / TNT 899 This module is universal, it controls the valve mechanism, not the exhaust itself. Your exhaust must have a butterfly valve with an actuator arm compatible with electric operation. Confirm exhaust compatibility before ordering. If your bike model isn't listed but runs a valved slip-on, this module will work. What's in the Box 1 × Valvetronic Electric Control Unit 1 × Electric actuator assembly Wiring harness and connectors Mounting hardware Exhaust system not included. Module requires a compatible valved exhaust to function. Specifications Control Type: Automatic (electric / solenoid-actuated) Actuation: Electric servo / solenoid butterfly valve operation Power Required: 12V DC (motorcycle battery) ECU Integration: Signal tap, no remapping required Valve Positions: Open / Closed (auto-switching) Override: Manual switch override supported Mount: Control unit + actuator on exhaust valve arm Fitment: Universal, compatible with electrically-actuated valved exhausts Brand: Valvetronic MRP: ₹6,499 Manual vs Electric, Which One to Choose Feature Manual (₹3,499) Electric / Auto (₹6,499) Valve Control Rider-operated switch Automatic (RPM/throttle-based) Power Required None 12V (bike battery) Wiring Not required Signal tap required Install Complexity Simple Moderate Failure Points Minimal (cable only) Electronic components Best For Riders who want full manual control Riders who want a set-and-forget system Also Available Prefer a simpler, zero-electronics setup? The Valvetronic Manual Module gives you direct cable-pull control from your handlebar, no wiring, no power required. View the Manual Module →

Read more less

NGage Hyper Flow Air Filter (NGAGE-007JAW300) for Jawa Classic, Forty Two & Yezdi Roadster, Washable Cotton Performance Replacement The NGage Hyper Flow Air Filter (NGAGE-007JAW300) is a reusable, washable cotton-gauze air filter developed for motorcycles built on the Jawa, Yezdi 300-334 cc platform. This air filter is designed as a direct replacement for the stock paper air filter used on the Jawa ClassicJawa Forty Two, and Yezdi Roadster. As stated on NGage’s official product page and compatibility panel, this air filter is specified for the following motorcycles: Jawa Classic Jawa Forty Two Yezdi Roadster This listing covers these three models exactly as specified by the manufacturer. Designed for Jawa Classic, Forty Two & Yezdi Roadster NGage specifies this Hyper Flow Air Filter for motorcycles built on the Jawa, Yezdi platform. From the NGage product page: Suitable For: Jawa Classic Jawa Forty Two Yezdi Roadster The filter is engineered to fit directly into the factory airbox of the above motorcycles without requiring any cutting, trimming, or airbox modification. It is intended as a stock-replacement air filter element for routine service or intake performance upgrades. Hyper Flow Cotton Filter Construction NGage classifies the NGAGE-007JAW300 as a Hyper Flow Air Filter using a cotton-based filtering medium. From the product page and icon set: The filtering media is stated as 100% organic cotton The filter is described as washable and reusable The cotton media is supported by a molded filter frame to maintain structural shape inside the airbox The filter is designed for long-term reuse through periodic cleaning NGage does not publish micron ratings, pore size data, or laboratory filtration efficiency figures for this product. Airflow and Performance (Manufacturer-Stated) As per NGage’s official product material and feature icons, the NGage Hyper Flow Air Filter NGAGE-007JAW300 carries the following manufacturer-stated performance claims: Up to 30% increased air flow than stock filter No horsepower or torque increase figure is shown for this specific model on the NGage product page or artwork. Reusable and Serviceable Design The NGage Hyper Flow Air Filter is designed to be washed, serviced, and reused. Unlike disposable paper air filters that are replaced at each service interval, this cotton-gauze filter is intended to be cleaned and reused periodically. From the product page: The filter is described as washable The filter is described as reusable The filter uses cotton as the filtering medium NGage does not specify a fixed cleaning interval.Service frequency will depend on: Riding environment Dust exposure Terrain conditions Mileage covered Durability and Testing Claims From the product page and icon set, NGage states: Best durability Extensively tested on all terrains Hassle-free installation Eco-friendly product 100% organic cotton as filtering media These attributes are manufacturer-stated product characteristics as displayed on the NGage product page. Warranty Information (Manufacturer-Stated) From the NGage product page and feature icons: Replacement warranty: 100,000 kilometers NGage does not publish additional warranty terms or conditions on the product page. Warranty Note (RawTorque) RawTorque is an authorized reseller of NGage products and does not provide a separate warranty on this item. Any warranty coverage, replacement terms, or service claims are governed solely by NGage’s official warranty policy. RawTorque can assist customers in coordinating manufacturer warranty support where applicable. Manufacturing Origin From the NGage product artwork: Made in India Compatibility As per NGage’s official product page and compatibility panel for part number NGAGE-007JAW300: Jawa Classic Jawa Forty Two Yezdi Roadster Variant Explanation This listing is for: NGage Hyper Flow Air Filter Part Number: NGAGE-007JAW300 No alternate sizes, shapes, or engine-specific variants are shown or specified by NGage for this product. Specifications (Manufacturer-Verified Only) Brand: NGage Product Type: Hyper Flow Air Filter Part Number: NGAGE-007JAW300 Filter Media: 100% organic cotton Reusable: Yes Washable: Yes Installation Type: Direct replacement Application: Motorcycle air filter Compatibility: Jawa Classic, Jawa Forty Two, Yezdi Roadster Manufacturing Origin: India Airflow Claim: Up to 30% increased airflow than stock filter Warranty: Replacement warranty up to 100,000 km Testing Claim: Extensively tested on all terrains Installation / Usage Notes Install only on Jawa Classic, Jawa Forty Two, and Yezdi Roadster motorcycles. Designed to fit inside the factory airbox. Clean and reuse the filter periodically as required. Service frequency depends on riding conditions and dust exposure.

Read more less

HB 155 / HBS 155 Front Brake Pads, Whisker Ceramic & Sintered (Front Only) The NGage HB 155 and HBS 155 are disc brake pads for motorcycles whose front brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the front: Jawa 42 Jawa Classic Note. Royal Enfield, Bajaj and Yamaha riders are served by their own HB 155 front listings on this store. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 155 is the Whisker Ceramic compound. HBS 155 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 155, Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 155, Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Front Pad codes: HB 155 (Whisker Ceramic), HBS 155 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

Rolon BPR brass-plated sealed chain and sprocket kit for the Yezdi Roadster and Yezdi Adventure. Supplied as a complete drivetrain set, matched to OE gearing.What's in the kit Brass-plated sealed chain R520HNXRC-105+1 Front sprocket 13T (S-02-715), 2 holes Rear sprocket 45T (S-02-949), 5 holes Rolon kit reference HNXRC 428NF Why the BPR kit Quadruple-sealed ring construction holds factory grease in and grit out Brass plating for corrosion resistance, worth having on an Adventure that sees dirt and water Rubberised front sprocket damps drivetrain noise and acts as a damper Hardened sprocket teeth for wear resistance and fatigue strength Chain and sprockets wear together and should always be replaced as a set. Message us for fitment guidance if you are unsure which model you have.

Read more less

NGage B8RII-8 Double Iridium Spark Plug, Universal Fitment The NGage B8RII-8 is a Double Iridium spark plug made in Japan, compatible with BS-4 and BS-6 vehicles. It fits a wide range of mid-to-large displacement motorcycles across Royal Enfield, Triumph, Kawasaki, Yamaha, Bajaj, Benelli, Harley-Davidson, Suzuki, TVS, Aprilia, Jawa, Yezdi, and Hero platforms. If your service manual or mechanic specifies B8RII-8 as the correct plug code, this is the exact component. Technical Specifications Part Number B8RII-8 Brand NGage Powerparts Series Double Iridium Origin Made in Japan Thread Diameter 14 mm Heat Range 8 Electrode Type Double iridium (iridium centre + iridium ground) BS Compliance BS-4 and BS-6 compatible Supplied As Single plug Why Double Iridium Unlike standard iridium plugs that use iridium only on the centre electrode, the B8RII-8 uses iridium on both the centre and ground electrodes. This means: Spark erosion is distributed across both electrodes, significantly longer service life Consistent spark energy throughout the plug's lifespan, not just when new More reliable cold starts and stable combustion at all RPM ranges Suitable for high-displacement engines with higher ignition demand Full Compatibility Reference fitment guidance available per NGage compatibility data. Always cross-reference against your owner's manual or service documentation before purchase. Royal Enfield Himalayan 411 Himalayan 440 Interceptor 650 Continental GT 650 Bear 650 Super Meteor 650 Shotgun 650 Classic 650 Triumph Tiger 1050 Tiger 1050 Sport Sprint GT Speed Triple Speed Triple 1050 Speed Triple R Tiger 1200 Explorer Tiger 1200 XC Tiger 1200 XR Tiger Trophy Kawasaki Ninja 300 Ninja 250R Ninja Z250 Z900 Yamaha YZF R15 (V1, V2, V3 & V4) MT-15 YZF R3 MT-03 Aerox V2 / NVX 155 Bajaj Pulsar 200NS Triple Spark (Side Plugs × 2) Pulsar NS200 Triple Spark (Side Plugs × 2) Pulsar RS200 Triple Spark (Side Plugs × 2) Benelli 502 C TRK 502 TRK 502 X Leoncino 500 Harley-Davidson Street 750 Street Rod 750 Suzuki Suzuki 125 Burgman Suzuki V-Strom 250 TVS Motor Company Apache RTR 160 Apache RTR 180 ABS Aprilia SR 125 SR 150 Jawa Forty Two Bobber 42 350 42 FJ Yezdi Roadster Adventure Scrambler Hero MotoCorp Xpulse 200 2V / 200T Compatibility is specification-based per NGage fitment data. Verify against your service manual before ordering. Bajaj Pulsar NS200, RS200, and 200NS Triple Spark models require 2 units (side plug positions). Installation Notes Verify pre-set gap against your manufacturer's specification before installation Tighten to the torque value specified in your service manual Clean threads before installation; do not over-torque Bajaj Pulsar NS200 / RS200 / 200NS Triple Spark side plug positions require 2 units per bike In The Box 1 × NGage B8RII-8 Double Iridium Spark Plug Terminal Type This plug is supplied with a bare threaded terminal stud. That is how it leaves the factory, and no terminal nut is fitted. A plug cap that screws onto the thread fits as supplied. If your cap seats on a terminal nut instead, a standard screw-on spark plug terminal nut can be fitted to the stud.

Read more less

The Celesta Max is the top of Red Rooster's Jawa range, and this version is built for the 42 Bobber. Stainless steel, mandrel-bent, packed with ceramic wool so it holds its note without repacking. The Bobber is a bike bought on stance and sound, and the Max is the fullest voiced can in the Celesta family, deeper and rounder than the standard Celesta without tipping into noise for its own sake. Polish, Black and Matte share the same bore, bends and mounting, so the finish changes the look and nothing else. Light blueing near the joint is normal on stainless steel after heat cycles. Fitment guidance Red Rooster lists this against the Jawa 42 Bobber, model years 2022 to 2024. The year range matters on this one. Other Jawa models take the Celesta or Celesta Pro, listed separately. If you are unsure which year or variant you have, message us before ordering and we will help you confirm it. Specifications Brand: Red Rooster Performance Product line: Celesta Max Material: Stainless steel Packing: Ceramic wool, no repacking required Finish options: Polish, Black, Matte Mounting: Direct bolt-on ECU remap required: Not mandatory Installation Bolt-on at the factory mounting points, no cutting or welding. A workshop fit is worth it for alignment and torque at the joint. In the box 1 x Red Rooster Celesta Max exhaust in the finish you select Mounting hardware and dB killer

Read more less

The Celesta is Red Rooster's exhaust for the Jawa platform, and the entry point into their range for these bikes. Stainless steel, mandrel-bent, packed with ceramic wool so it holds its note without repacking. The Jawa 350 single already has a distinctive character, and the Celesta is voiced to deepen it rather than replace it, with more presence low down and a cleaner pickup off idle. Polish and Black share the same bore, bends and mounting, so the finish changes the look and nothing else. Light blueing near the joint is normal on stainless steel after heat cycles. Fitment guidance Red Rooster lists the Celesta under its Jawa range, covering: Jawa Classic Jawa 42 Yezdi Roadster The Jawa 42 Bobber and the Yezdi Roadster BS6 2.0 take the Celesta Max instead, which is listed separately. If you are unsure which of these you have, message us and we will help you confirm it. Specifications Brand: Red Rooster Performance Product line: Celesta Material: Stainless steel Packing: Ceramic wool, no repacking required Finish options: Polish, Black Mounting: Direct bolt-on ECU remap required: Not mandatory Installation Bolt-on at the factory mounting points, no cutting or welding. A workshop fit is worth it for alignment and torque at the joint. In the box 1 x Red Rooster Celesta exhaust in the finish you select Mounting hardware and dB killer

Read more less

The Celesta Pro sits above the standard Celesta in Red Rooster's Jawa range. Stainless steel, mandrel-bent, ceramic wool packed so it holds its note without repacking. Compared with the Celesta it is voiced with more body and a deeper tone at cruising revs, which is what most riders are after on these bikes rather than outright volume. Polish and Black share the same bore, bends and mounting, so the finish changes the look and nothing else. Light blueing near the joint is normal on stainless steel after heat cycles. Fitment guidance Red Rooster lists the Celesta Pro under both its Jawa and Jawa 42 FJ ranges, covering: Jawa Classic Jawa 42 Jawa 42 FJ The Jawa 42 Bobber takes the Celesta Max instead, listed separately. If you are unsure which model you have, message us and we will help you confirm it. Specifications Brand: Red Rooster Performance Product line: Celesta Pro Material: Stainless steel Packing: Ceramic wool, no repacking required Finish options: Polish, Black Mounting: Direct bolt-on ECU remap required: Not mandatory Installation Bolt-on at the factory mounting points, no cutting or welding. A workshop fit is worth it for alignment and torque at the joint. In the box 1 x Red Rooster Celesta Pro exhaust in the finish you select Mounting hardware and dB killer

Read more less

HB 163 / HBS 163 Rear Brake Pads, Whisker Ceramic & Sintered (Rear Only) The NGage HB 163 and HBS 163 are disc brake pads for motorcycles whose rear brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the rear: Suzuki Gixxer 250 Suzuki V-Strom 250 SX Honda CBR 250R (non-ABS) Honda CBR 250R (ABS, Nissin calipers) Triumph Street Triple 675 Triumph Street Triple 675 R Ducati Monster 797 Ducati Scrambler Jawa 42 Jawa Classic Yezdi Roadster Yezdi Adventure BMW G 310 R BMW G 310 GS BMW S1000R (2014-2024) Note. Royal Enfield, KTM, Bajaj, Triumph 400 and Ather riders are served by their own HB 163 listings on this store. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 163 is the Whisker Ceramic compound. HBS 163 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 163, Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 163, Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Rear Pad codes: HB 163 (Whisker Ceramic), HBS 163 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

Rolon BPR brass-plated sealed chain and sprocket kit for the Jawa Perak 334cc. Supplied as a complete drivetrain set, matched to OE gearing.What's in the kit Brass-plated sealed chain R520HXRC-114-2 Front sprocket 13T (S 02 715), 2 holes Rear sprocket 45T (S 02 949), 5 holes Rolon kit reference HXRC 374NF Why the BPR kit Quadruple-sealed ring construction holds factory grease in and grit out Brass plating for corrosion resistance and a lasting gold finish that suits the Perak's blacked-out look Rubberised front sprocket damps drivetrain noise and acts as a damper Hardened sprocket teeth for wear resistance and fatigue strength Chain and sprockets wear together and should always be replaced as a set. Message us for fitment guidance if you are unsure which model year you have.

Read more less

CRANK1 performance brake pads for the Jawa Perak, all in one place. Choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Jawa Perak:RearFront fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Jawa Perak?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

Vesrah SD-953 Rear Ceramic Brake Pads for Jawa and Yezdi Motorcycles Product Description The Vesrah SD-953 Rear Ceramic Brake Pads are designed for motorcycles that use the SD-953 rear brake pad shape. Manufactured in Japan, these brake pads use a ceramic composite compound engineered for stable braking performance and reduced brake dust. The Vesrah SD-953 rear brake pads are built as a direct replacement pad set compatible with motorcycles such as the Jawa 42, Yezdi Roadster, and Yezdi Adventure. The ceramic compound construction is designed to deliver smooth braking feel, consistent stopping power, and reliable everyday braking performance. Ceramic brake pad materials are known for producing lower brake dust and predictable braking response, helping maintain stable braking behaviour during regular riding conditions. The pad compound interacts with the brake rotor to provide controlled braking while minimizing excessive rotor wear. For riders replacing worn rear brake pads on their Jawa or Yezdi motorcycle, the Vesrah SD-953 ceramic rear brake pads provide a direct-fit replacement designed for everyday street riding. Compatible Motorcycles (Rear Brake) Jawa 42Yezdi RoadsterYezdi Adventure Specifications Brand: VesrahPad Code: SD-953Material: Ceramic CompositePosition: Rear BrakeCountry of Origin: JapanQuantity: 1 Set (Rear Brake Pads)

Read more less