Chevrolet

NGK Iridium IX. A 0.6mm fine-wire iridium centre electrode in place of a conventional one, firing a sharper, more focused spark. On a small-capacity car that does most of its work in traffic, that means easier starts, a steadier idle and cleaner running. Iridium barely erodes, so the gap holds and you change plugs far less often. Direct fit. Nothing to adjust. Find your car Maruti Suzuki Maruti 800i 12v · Alto 0.8i 12v · Alto 800 · New Alto BS6 three-cylinder, takes 3 Alto 1.1i 16v · Wagon R 1.1i four-cylinder, takes 4 Zen Estilo came as both, check yours Chevrolet · Beat Takes 4 Fiat · Palio 1.2 i.e. · Stile 1.1i · Sport · Siena 1.2i Takes 4 Count your ignition coils or plug leads if you are unsure how many you need, or send us your model and year and we will tell you. The Alto K10 from July 2022 runs the newer K10C engine and takes the ILZKR6F11 instead, also on our site. Running CNG? These are among the most CNG-converted cars in India, and this is the plug for them on gas as much as on petrol. NGK lists no separate CNG part, and the heat range here is the same 7 as the standard plug, so it is a straight replacement either way. Where iridium earns its keep on gas is different from petrol: CNG needs more voltage to ignite. The 0.6mm fine wire concentrates the spark and fires at lower voltage, which counts for most on an older car whose coil and leads are no longer new. CNG wears electrodes faster. Gas is harder on a plug than petrol is, and iridium barely erodes. On a CNG car a conventional plug is something you replace often, and that is the cost this removes. Fit as supplied. Have the plugs checked earlier than you would on a petrol-only car, since gas is harder on them. And if the car has become hard to start on gas, worn plugs are the first thing to rule out. Specifications Part number · DCPR7EIX Type · Iridium IX, 0.6mm fine wire Heat range · 7, the same as the standard plug Conventional equivalent · DCPR7E Sold as · pack of 2, 3 or 4 Fitting Arrives pre-gapped and ready to fit. Thread in by hand first, then torque to your manual's figure. If you check the gap, move the outer electrode only. Unsure which you need? Send us your model and year and we will confirm before you order.

Read more less

NGK Iridium IX. A 0.6mm fine-wire iridium centre electrode in place of a conventional one, firing a sharper, more focused spark. On an older engine that means noticeably easier starting, a steadier idle and cleaner running, and iridium holds its gap far longer than the nickel plug it replaces. Direct fit. Nothing to adjust. Find your car Maruti Suzuki Maruti 800 · Omni 0.8, carburettor and MPFI three-cylinder, takes 3 Maruti 1000 · Zen 1.0 · Gypsy 1.3 four-cylinder, takes 4 Toyota · Qualis · Chevrolet · Astra 1.6i · Corsa 1.6i Takes 4 The 796cc Maruti 800 and Omni are three-cylinder engines and need three plugs, not four. Count your plug leads if you are unsure, or send us your model and we will confirm before you order. Alto or Wagon R? Those take the DCPR7EIX, also on our site. Specifications Part number · BPR5EIX Type · Iridium IX, 0.6mm fine wire Heat range · 5 Conventional equivalent · BPR5ES Sold as · pack of 2, 3 or 4 Fitting Arrives pre-gapped and ready to fit. Thread in by hand first, then torque to your manual's figure. If you check the gap, move the outer electrode only. Unsure which you need? Send us your model and year and we will confirm before you order.

Read more less

NGK Iridium IX. A 0.6mm fine-wire iridium centre electrode in place of a conventional one, firing a sharper, more focused spark. In everyday driving that shows up as easier cold starts, a steadier idle and cleaner combustion, and because iridium barely erodes the gap stays where the factory set it. Direct fit. Nothing to adjust. Find your car Maruti Suzuki Takes 4 Swift 1.3 · first generation, 2005 to mid-2011 SX4 · Versa 1.3i · Gypsy King 1.3i Esteem 1.3 MPFI · Baleno 1.6 old model · Zen 1.0i 16V MPFI Eeco 1.2 · Super Carry 1.2 (Mar 2017 to Apr 2020) Tata Indica 1.4 · Indica Xeta · Indigo · Indigo Marina · Indigo XL Takes 4 Nano two-cylinder, takes 2 Chevrolet · Optra 1.8 · Fiat · Uno 1.0i & 1.2 Takes 4 Nano owners: the 624cc engine is a two-cylinder and needs two plugs, not four. Our pack of 2 is the one you want. Driving a newer Swift? Find your year here The Swift has run four different engines, and they do not share a plug. This page is the first one only. 2005 to mid-2011 · Swift 1.3 · this plug, BKR6EIX Oct 2014 to Feb 2021 · 1.2 K12M · takes the LKR7BIX-P, linked below 2021 onward · 1.2 K12N DualJet · takes the ILZKR6F11 May 2024 onward · 1.2 Z12E · takes the ILKAR7Z11S Swift built between Aug 2011 and Oct 2014? That one uses a plug NGK does not sell in India. Message us and we will tell you what your options are rather than sell you the wrong part. Specifications Part number · BKR6EIX Type · Iridium IX, 0.6mm fine wire Heat range · 6 Conventional equivalent · BKR6E Sold as · pack of 2, 3 or 4 Fitting Arrives pre-gapped and ready to fit. Thread in by hand first, then torque to your manual's figure. If you check the gap, move the outer electrode only. Unsure which you need? Send us your model and year and we will confirm before you order.

Read more less

NGK Iridium IX. A 0.6mm fine-wire iridium centre electrode in place of a conventional one, firing a sharper, more focused spark. In everyday driving that shows up as easier cold starts, a steadier idle and cleaner combustion, and because iridium barely erodes the gap stays where the factory set it. Direct fit. Nothing to adjust. Find your car Honda Takes 4 City 1.3 & 1.5 · up to Sept 2008 Amaze · Jun 2018 to current · 1200cc from Jan 2020 WR-V Edge · Mar 2018 to current Jazz 1.2 · Aug 2018 to current Brio Maruti Suzuki Grand Vitara 1.6 & 2.0 four-cylinder, takes 4 Grand Vitara 2.7 V6, takes 6 Chevrolet · Aveo 1.4 & 1.6 · Optra 1.6 · SRV Takes 4 Grand Vitara 2.7 owners: that engine is a V6 and needs six plugs. Choose the pack of 6 above. Driving a later City? Oct 2008 to Sept 2014 takes the IZFR6K-13, 2015 to 2019 the DIFR6D13, and the 1.5 from 2020 the DILZKAR7C11H. All are on our site. Specifications Part number · BKR6EIX-11 Type · Iridium IX, 0.6mm fine wire Heat range · 6 Conventional equivalent · BKR6E-11 Sold as · pack of 2, 3, 4 or 6 Fitting Arrives pre-gapped and ready to fit. Thread in by hand first, then torque to your manual's figure. If you check the gap, move the outer electrode only. Unsure which you need? Send us your model and year and we will confirm before you order.

Read more less

Pagid T1959N is a front-axle brake pad set for the Chevrolet CRUZE (2009 - ), using the Pagid OEM compound, an OE-quality replacement pad from an original-equipment supplier.Pagid OEM characteristics Intended use Everyday road driving Equivalence OE-quality replacement Heritage Pagid is an OE brake supplier to European manufacturers Fitment guidanceListed against the Chevrolet CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by Pagid.

Read more less

BrakeKraft BK569070 is a front-axle brake disc for the Chevrolet CRUZE (2009 - ), from the BrakeKraft Drilled & Slotted range, a cross-drilled and slotted performance disc.BrakeKraft Drilled & Slotted characteristics Surface Cross-drilled and slotted Intended use Performance road driving Purpose of drilling Vents gas and heat away from the pad face Purpose of slotting Clears dust and debris, keeps the pad surface biting cleanly Fitment guidanceListed against the Chevrolet CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. Discs are sold individually and replaced as a pair, so you need two for the axle.Compound characteristics as published by BrakeKraft.

Read more less

BrakeKraft BK569071 is a rear-axle brake disc for the Chevrolet CRUZE (2009 - ), from the BrakeKraft Drilled & Slotted range, a cross-drilled and slotted performance disc.BrakeKraft Drilled & Slotted characteristics Surface Cross-drilled and slotted Intended use Performance road driving Purpose of drilling Vents gas and heat away from the pad face Purpose of slotting Clears dust and debris, keeps the pad surface biting cleanly Fitment guidanceListed against the Chevrolet CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the rear axle. Discs are sold individually and replaced as a pair, so you need two for the axle.Compound characteristics as published by BrakeKraft.

Read more less

DBA DB2268SS is a brake pad set for the Chevrolet CRUZE (2009 - ), using the DBA Street Series (SS) compound, a comfort-focused street pad with low noise and low dust.DBA Street Series (SS) characteristics Intended use General light-duty street driving Priority Comfort: low noise, low dust Bedding in Bedding-in stripe gives higher initial friction while the pad beds Fitment guidanceListed against the Chevrolet CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.Compound characteristics as published by DBA.

Read more less

DBA DB1841SS is a brake pad set for the Chevrolet TRAIL BLAZER, using the DBA Street Series (SS) compound, a comfort-focused street pad with low noise and low dust.DBA Street Series (SS) characteristics Intended use General light-duty street driving Priority Comfort: low noise, low dust Bedding in Bedding-in stripe gives higher initial friction while the pad beds Fitment guidanceListed against the Chevrolet TRAIL BLAZER. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.Compound characteristics as published by DBA.

Read more less

DBA DB1232SS is a brake pad set for the Chevrolet Forester, using the DBA Street Series (SS) compound, a comfort-focused street pad with low noise and low dust.DBA Street Series (SS) characteristics Intended use General light-duty street driving Priority Comfort: low noise, low dust Bedding in Bedding-in stripe gives higher initial friction while the pad beds Fitment guidanceListed against the Chevrolet Forester. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.Compound characteristics as published by DBA.

Read more less

HEL Braided Brake Lines for the Chevrolet cruze. HEL Performance designs and manufactures its stainless braided lines in Britain, a fixture on race and road cars worldwide.Stainless steel braided hoses replace the flex of rubber lines for a firmer, more consistent pedal and sharper brake feel, wrapped in a protective PVC cover.Pre-order item - supplied genuine by Rawtorque; availability is confirmed after you order.Part numbers NA: HCRUFitment guidance - listed as a fit for:Chevrolet cruzeCross-referenced to Brembo OE numbers. Not sure it's right for your car? Share your VIN and our team will help confirm fitment.

Read more less

BMC FB392/01 Performance Air Filter for Tata DICOR PlatformTata's DICOR diesels powered a generation of rugged SUVs, keep them flowing.The BMC FB392/01 is a direct-fit washable performance air filter for the Tata Safari, Hexa, Aria, Xenon, Movus (2.0 / 2.2 DICOR diesel) and Chevrolet Forester (2.5). BMC reusable cotton-gauze media replaces the stock element.This is a direct-fit replacement: it drops straight into the factory airbox with no cutting, no modification, and no extra hardware. Fits the Tata Safari, Hexa, Aria, Xenon and Movus 2.0/2.2 DICOR.Why riders choose BMC Washable and reusable: clean it, re-oil it, refit it. One filter for the life of the car. Multi-layer cotton gauze for higher airflow than a stock paper element, without leaving the engine exposed. Made in Italy by BMC, an OEM and motorsport-grade air filter manufacturer. Genuine BMC, supplied by Rawtorque as an authorised stockist.

Read more less

EBC DP42067R is a front-axle brake pad set for the CHEVROLET CRUZE (2009 - ), using the EBC Yellowstuff compound, a fast-street pad with high friction from cold, built on an aramid-fibre compound.EBC Yellowstuff characteristics Compound Aramid fibre, copper-free since 2021 Intended use Fast street driving Cold friction High bite from cold, no warm-up needed Green fade threshold 400 °C (750 °F), per EBC Dust Not a low-dust pad Bedding in Beds naturally over the first 100-200 miles of urban use Approval ECE R90 approved for street use Fitment guidanceListed against the CHEVROLET CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by EBC.

Read more less

EBC DPX2113 is a front-axle brake pad set for the Chevrolet & Isuzu, using the EBC Ultimax compound, an OE-replacement pad built for quiet, low-dust daily driving.EBC Ultimax characteristics Intended use Everyday road driving, hot and cold climates Equivalence Direct OE replacement Friction rating GG Dust Minimal Noise One of EBC's quietest formulations Bedding in BRAKE-IN surface coating for a fast bed-in Approval ECE R90 approved Fitment guidanceListed against the Chevrolet & Isuzu. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by EBC.

Read more less

EBC DPX2067 is a front-axle brake pad set for the CHEVROLET CRUZE (2009 - ), using the EBC Ultimax compound, an OE-replacement pad built for quiet, low-dust daily driving.EBC Ultimax characteristics Intended use Everyday road driving, hot and cold climates Equivalence Direct OE replacement Friction rating GG Dust Minimal Noise One of EBC's quietest formulations Bedding in BRAKE-IN surface coating for a fast bed-in Approval ECE R90 approved Fitment guidanceListed against the CHEVROLET CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by EBC.

Read more less

EBC DP1636 is a front-axle brake pad set for the Chevrolet, Maruti/Suzuki & Nissan, using the EBC Ultimax compound, an OE-replacement pad built for quiet, low-dust daily driving.EBC Ultimax characteristics Intended use Everyday road driving, hot and cold climates Equivalence Direct OE replacement Friction rating GG Dust Minimal Noise One of EBC's quietest formulations Bedding in BRAKE-IN surface coating for a fast bed-in Approval ECE R90 approved Fitment guidanceListed against the Chevrolet, Maruti/Suzuki & Nissan. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by EBC.

Read more less

Brembo P59080 is a rear-axle brake pad set from Brembo's Prime range for the Chevrolet CRUZE (2009 - ), measuring 117 mm wide, 43 mm tall and 16 mm thick.Prime is Brembo's OE-matched road range. The friction material is specified to match original equipment braking performance, the backplate is painted against corrosion, an anti-squeal shim is included, and the set is ECE R90 type-approved. Brembo lists it as the pad to run with Prime brake discs.This is not the Xtra range, which is Brembo's sport pad line for drilled discs, and not the ceramic (N-suffix) range, which we do not currently stock.Specification Range Brembo Prime Technical content OE-matched Axle Rear Width 117 mm Height 43 mm Thickness 16 mm Braking system TRW WVA number 25096,25097,25098 FMSI D1468 8668 Backplate Black, painted Accessories Anti-squeal shim Wear indicator Acoustic, built into the pad Approval ECE R90 type-approved EAN code 8020584103524 These pads carry an acoustic wear indicator, a metal tab that contacts the disc and squeals once the friction material nears its limit. Treat that noise as a prompt to inspect the pads.Fitment guidanceListed against the Chevrolet CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the rear axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

Brembo P59077X is a front-axle brake pad set for the Chevrolet CRUZE (2009 - ), measuring 148 mm wide and 61 mm tall.Brembo Prime pads are OE-matched for braking performance, low noise and comfort on the road.Specification Width 148 mm Thickness 19 mm Height 61 mm Braking system Bosch WVA number 25035,25036,25034 FMSI D1467 8667 Wear indicator Acoustic Accessories With accessories With anti-squeal shim Axle Front EAN code 8020584069080 These pads are prepared for a wear indicator. If your car uses an electronic wear sensor, the sensor is a separate part and is normally replaced at the same time as the pads.Fitment guidanceListed against the Chevrolet CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

Brembo P59077 is a front-axle brake pad set from Brembo's Prime range for the Chevrolet CRUZE (2009 - ), measuring 148 mm wide, 61 mm tall and 19 mm thick.Prime is Brembo's OE-matched road range. The friction material is specified to match original equipment braking performance, the backplate is painted against corrosion, an anti-squeal shim is included, and the set is ECE R90 type-approved. Brembo lists it as the pad to run with Prime brake discs.This is not the Xtra range, which is Brembo's sport pad line for drilled discs, and not the ceramic (N-suffix) range, which we do not currently stock.Specification Range Brembo Prime Technical content OE-matched Axle Front Width 148 mm Height 61 mm Thickness 19 mm Braking system Bosch WVA number 25034,25035,25036 FMSI D1467 8667 Backplate Black, painted Accessories Anti-squeal shim Wear indicator Acoustic, built into the pad Approval ECE R90 type-approved EAN code 8020584083901 These pads carry an acoustic wear indicator, a metal tab that contacts the disc and squeals once the friction material nears its limit. Treat that noise as a prompt to inspect the pads.Fitment guidanceListed against the Chevrolet CRUZE (2009 - ). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

Brembo P34007 is a front-axle brake pad set from Brembo's Prime range for the Chevrolet & Isuzu, measuring 152 mm wide, 61 mm tall and 17 mm thick.Prime is Brembo's OE-matched road range. The friction material is specified to match original equipment braking performance, the backplate is painted against corrosion, an anti-squeal shim is included, and the set is ECE R90 type-approved. Brembo lists it as the pad to run with Prime brake discs.This is not the Xtra range, which is Brembo's sport pad line for drilled discs, and not the ceramic (N-suffix) range, which we do not currently stock.Specification Range Brembo Prime Technical content OE-matched Axle Front Width 152 mm Height 61 mm Thickness 17 mm Braking system Akebono WVA number 25151,25150,25149 FMSI D1677 8906 Backplate Black, painted Accessories Anti-squeal shim Wear indicator Acoustic, built into the pad Approval ECE R90 type-approved EAN code 8020584104927 These pads carry an acoustic wear indicator, a metal tab that contacts the disc and squeals once the friction material nears its limit. Treat that noise as a prompt to inspect the pads.Fitment guidanceListed against the Chevrolet & Isuzu. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

Brembo P23126 is a front-axle brake pad set from Brembo's Prime range for the Chevrolet, Maruti/Suzuki & Nissan, measuring 137 mm wide, 53 mm tall and 16 mm thick.Prime is Brembo's OE-matched road range. The friction material is specified to match original equipment braking performance, the backplate is painted against corrosion, an anti-squeal shim is included, and the set is ECE R90 type-approved. Brembo lists it as the pad to run with Prime brake discs.This is not the Xtra range, which is Brembo's sport pad line for drilled discs, and not the ceramic (N-suffix) range, which we do not currently stock.Specification Range Brembo Prime Technical content OE-matched Axle Front and rear Width 137 mm Height 53 mm Thickness 16 mm Braking system Hitachi WVA number 24280,24281,24282 FMSI D815 8530 Backplate Black, painted Accessories Anti-squeal shim Wear indicator Acoustic, built into the pad Approval ECE R90 type-approved EAN code 8020584060391 These pads carry an acoustic wear indicator, a metal tab that contacts the disc and squeals once the friction material nears its limit. Treat that noise as a prompt to inspect the pads.Fitment guidanceListed against the Chevrolet, Maruti/Suzuki & Nissan. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

Brembo 09B35611 (front, 300 mm diameter) and Brembo 08B35111 (rear, 292 mm diameter) are the OE-specification brake discs for the Chevrolet CRUZE (2009 - ).Use the Position selector to choose the axle you need. The Set option covers both axles together.Brembo Prime is the OE-equivalent disc line, developed for road use and finished with a corrosion coating.Front axle specification, 09B35611 Diameter 300 mm Thickness 26 mm Minimum thickness 23 mm Height 46 mm Bolt holes 5 Centering bore 71 mm Disc type Ventilated Units per box 1 EAN code 8020584038260 Rear axle specification, 08B35111 Diameter 292 mm Thickness 12 mm Minimum thickness 10 mm Height 45 mm Bolt holes 5 Centering bore 71 mm Disc type Solid Units per box 1 EAN code 8020584028445 Measure at the thinnest point across the braking surface: front is 26 mm new against a 23 mm minimum, rear is 12 mm new against a 10 mm minimum. Once a disc reaches minimum thickness it must be replaced rather than resurfaced.Fitment guidanceListed against the Chevrolet CRUZE (2009 - ). Front and rear use different part numbers, and brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.Each Position option covers a single axle. Discs are sold individually and replaced as a pair, so you need two for the axle.Specifications published by Brembo.

Read more less