New Arrivals

NGage Hyper Flow Universal Pod Air Filter – 49mm ID, 150-250cc Read this first. NGage supplies this filter for closed track purposes. It is a pod filter: it replaces the airbox rather than sitting inside it. That changes how the engine draws air and takes the motorcycle away from the intake configuration it was emissions-tested in, so it is not intended for a road-registered bike in regular use. Fit it to a track or competition machine, or one you are prepared to run outside stock specification. What it is A washable, reusable cotton-gauze pod filter with a 49mm internal diameter inlet, sized for motorcycles in the 150cc to 250cc range running an aftermarket or open intake. Four layers of surgical-grade cotton gauze sit between epoxy-coated aluminium mesh, with support pillars to hold the shape under airflow. It arrives factory pre-oiled. Unlike the model-specific Hyper Flow filters we stock, this one is not cut to any particular airbox. It is a universal part, and fitment depends on your intake plumbing rather than on your motorcycle model. Will it fit The only number that matters is the inlet internal diameter: 49mm. Measure the outside diameter of the throttle body spigot or intake tube you intend to clamp it to. If that measures 49mm, this filter fits. If it does not, this is the wrong part regardless of what motorcycle it is on. Because it is universal, we cannot confirm fitment from a model name alone. Send us the measurement and we will help with fitment guidance. Tuning A pod filter flows considerably more air than a stock airbox element. On a carburetted engine expect to rejet. On a fuel-injected engine the ECU will trim within its range, but the mixture will sit lean of where it should be under load, and a fuelling module or remap is the sensible companion to this part rather than an optional extra. Running an open pod on a stock map is the most common way to get a disappointing result from one, so plan the tune alongside the filter. Care Cotton gauze is washable and reusable. Clean and re-oil it when it is visibly loaded, sooner in dust. A pod filter sits in open air rather than inside a sealed box, so it picks up dirt faster than a panel filter does and wants checking more often. NGage sells a cleaning and recharge kit, and you can add one to this order using the option above. Specifications Brand: NGage Part number: NGAGE-017UNI49 Type: Universal pod air filter Inlet internal diameter: 49mm Engine range: 150-250cc Media: four-layer surgical cotton gauze, epoxy-coated aluminium mesh Washable and reusable: yes, factory pre-oiled Intended use: closed track, per NGage NGage publishes no dyno figure for this filter, so we are not quoting one.

Read more less

HB 155 / HBS 155 Rear Brake Pads – Whisker Ceramic & Sintered (Rear Only) The NGage HB 155 and HBS 155 are disc brake pads for motorcycles whose rear brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the rear: Harley-Davidson Street 750 Ducati Multistrada 950 Note. Pad code 155 is a front pad on several other motorcycles. This listing is the rear position only. Royal Enfield Super Meteor 650 and Shotgun 650 riders have their own HB 155 rear listing on this store. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 155 is the Whisker Ceramic compound. HBS 155 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 155 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 155 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Rear Pad codes: HB 155 (Whisker Ceramic), HBS 155 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

HB 155 / HBS 155 Front Brake Pads – Whisker Ceramic & Sintered (Front Only) The NGage HB 155 and HBS 155 are disc brake pads for motorcycles whose front brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the front: Jawa 42 Jawa Classic Yezdi Roadster Note. Royal Enfield, Bajaj and Yamaha riders are served by their own HB 155 front listings on this store. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 155 is the Whisker Ceramic compound. HBS 155 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 155 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 155 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Front Pad codes: HB 155 (Whisker Ceramic), HBS 155 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

HB 164 / HBS 164 Front Brake Pads – Whisker Ceramic & Sintered (Front Only) The NGage HB 164 and HBS 164 are disc brake pads for motorcycles whose front brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the front: Honda CBR 250R (non-ABS) Harley-Davidson Street 750 Yezdi Adventure Note. Royal Enfield 450 and 650 riders, and KTM Adventure Gen 3 riders, are served by their own HB 164 listings on this store. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 164 is the Whisker Ceramic compound. HBS 164 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 164 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 164 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Front Pad codes: HB 164 (Whisker Ceramic), HBS 164 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

HB 164 / HBS 164 Rear Brake Pads – Whisker Ceramic & Sintered (Rear Only) The NGage HB 164 and HBS 164 are disc brake pads for motorcycles whose rear brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the rear: BMW S1000XR (2018 onwards) BMW R1000 GS Ducati Multistrada 1200 (2015-2018) Note. Pad code 164 is a front pad on several other motorcycles. This listing is the rear position only; check your own chart entry before ordering. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 164 is the Whisker Ceramic compound. HBS 164 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 164 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 164 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Rear Pad codes: HB 164 (Whisker Ceramic), HBS 164 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

HB 089 / HBS 089 Front Brake Pads – Whisker Ceramic & Sintered (Front Only) The NGage HB 089 and HBS 089 are disc brake pads for motorcycles whose front brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the front: Honda CBR 250R (ABS, Nissin calipers) Honda CBR 650F (2014-2020) Triumph Street Triple 675 Triumph Tiger 800 Triumph Street Twin Triumph Bonneville T120 / T100 Kawasaki Versys 300 Note. Honda CB350, CB350RS and H'ness riders are served by their own HB 089 listing on this store. On the Versys 300 this is the front pad only; that motorcycle takes HB 087 / HBS 087 at the rear. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 089 is the Whisker Ceramic compound. HBS 089 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 089 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 089 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Front Pad codes: HB 089 (Whisker Ceramic), HBS 089 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

HB 163 / HBS 163 Rear Brake Pads – Whisker Ceramic & Sintered (Rear Only) The NGage HB 163 and HBS 163 are disc brake pads for motorcycles whose rear brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the rear: Suzuki Gixxer 250 Suzuki V-Strom 250 SX Honda CBR 250R (non-ABS) Honda CBR 250R (ABS, Nissin calipers) Triumph Street Triple 675 Triumph Street Triple 675 R Ducati Monster 797 Ducati Scrambler Jawa 42 Jawa Classic Yezdi Roadster Yezdi Adventure BMW G 310 R BMW G 310 GS BMW S1000R (2014-2024) Note. Royal Enfield, KTM, Bajaj, Triumph 400 and Ather riders are served by their own HB 163 listings on this store. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 163 is the Whisker Ceramic compound. HBS 163 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 163 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 163 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Rear Pad codes: HB 163 (Whisker Ceramic), HBS 163 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

HB-029 / HBS-029 Front Brake Pads – Whisker Ceramic & Sintered (Front Only) The NGage HB-029 and HBS-029 are disc brake pads for motorcycles whose front brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the front: Yamaha Aerox 155 (2023-2024) Yamaha NVX 155 V2 (2023-2024) Note. Model year decides the pad code. Aerox 155 and NVX 155 V2 built up to 2022 use HB-F081 / HBS-F081 instead. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB-029 is the Whisker Ceramic compound. HBS-029 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB-029 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS-029 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Front Pad codes: HB-029 (Whisker Ceramic), HBS-029 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

HB-F081 / HBS-F081 Front Brake Pads – Whisker Ceramic & Sintered (Front Only) The NGage HB-F081 and HBS-F081 are disc brake pads for motorcycles whose front brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the front: Yamaha Aerox 155 (till 2022) Yamaha NVX 155 V2 (till 2022) Note. Model year decides the pad code. Aerox 155 and NVX 155 V2 built from 2023 use HB-029 / HBS-029 instead. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB-F081 is the Whisker Ceramic compound. HBS-F081 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB-F081 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS-F081 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Front Pad codes: HB-F081 (Whisker Ceramic), HBS-F081 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

HB 087 / HBS 087 Rear Brake Pads – Whisker Ceramic & Sintered (Rear Only) The NGage HB 087 and HBS 087 are disc brake pads for motorcycles whose rear brake caliper specifies this exact pad shape. They are direct-replacement components and do not alter caliper geometry, disc size, or braking system architecture. Per the official NGage brake pad compatibility chart, the following motorcycles use this pad code at the rear: Honda Africa Twin Kawasaki Ninja 650 (2017-2020) Kawasaki Versys 300 Kawasaki Versys 650 Kawasaki Versys 1000 Yamaha R6 Note. On the Kawasaki Versys 300 this pad code is the rear only; that motorcycle uses HB 089 / HBS 089 at the front. Pad code and fitment logic A pad code defines the physical shape and mounting interface of the pad. Only pads carrying the matching code belong in a given caliper. HB 087 is the Whisker Ceramic compound. HBS 087 is the Sintered compound. Both share identical dimensions, backing plate profile and mounting points. Only the friction material differs. Fitting a pad of a different shape can cause improper seating, uneven wear, noise, reduced braking efficiency or damage to the brake system. Choosing between the two compounds HB 087 – Whisker Ceramic. A ceramic friction compound reinforced with whisker filament, blended with ceramic, mineral and aramid fibre and copper. NGage rates it for 15,000 to 25,000 km under normal riding, with thermal resistance to 650°C and a friction coefficient of 0.45 to 0.60. Chosen for controlled feel, low dust and quiet running on the road. HBS 087 – Sintered. A metallic compound fused under heat and pressure, using copper, steel and brass powders with graphite and carbon fibre modifiers. NGage rates it for 12,000 to 18,000 km, with thermal resistance to 1000°C and a friction coefficient of 0.55 to 0.65. Chosen for higher thermal stability and consistent bite under sustained load. Installation and service Brake pads are a wearing part. Replace them at the manufacturer's service interval or once pad thickness reaches the wear limit. Standard brake service applies: clean the caliper and pad guides, check disc condition, seat the pads correctly, torque the hardware to specification and bed the pads in before hard use. Professional installation is recommended for anyone not familiar with motorcycle brake service. Specifications Brand: NGage Product type: Motorcycle brake pads Position: Rear Pad codes: HB 087 (Whisker Ceramic), HBS 087 (Sintered) Sold as: one axle set Please confirm your pad code against the NGage chart or your existing pads before ordering. We are happy to help with fitment guidance.

Read more less

The lever feel a rubber hose gives awayA standard rubber brake line swells slightly every time you pull the lever. That expansion is movement the brake caliper never sees, and it is why a hot brake starts to feel soft halfway down a hill.This hose is built around a Diken Japan PTFE inner liner. PTFE holds its shape under pressure and heat, so the force applied at the lever arrives at the caliper instead of being absorbed by the line. The result is a firmer lever, a more predictable bite point and braking that behaves the same on the tenth stop as on the first.Fittings are chrome polished banjo, finished to sit properly on a bike where the brake line is visible.Specifications Diken Japan original PTFE inner liner Low expansion under pressure and heat Chrome polished banjo fittings Available in 850mm, 1000mm and 1300mm 850mm and 1000mm suit front and mid routing 1300mm suits rear and taller routing Line length depends on your motorcycle and on any bar or suspension changes. Get in touch for fitment guidance before ordering.

Read more less

Fuel for the stretch between fuel stopsOn the routes worth riding, the gap between pumps is the part nobody plans for. The Long-Haul is a 5 litre reserve built to mount cleanly on a motorcycle luggage setup and stay there over bad surfaces.The body is moulded from fuel safe high density plastic with a leak resistant cap. A key barrel option is available where the can is left on the bike unattended.Specifications Capacity 5 litres Fuel safe high density plastic Leak resistant sealing cap Available with or without a lockable key barrel Single and double pack options Designed for motorcycle luggage mounting Supplied in red. Get in touch for guidance on mounting to your motorcycle.

Read more less

One bag, four ways to carry itThe ARC was built with Vantora for riders who would rather adapt a single bag than own four. It wears as a thigh bag on the ride, converts to a sling or a waist pouch off the motorcycle, and works as a chest pack when the route turns to walking.A hard shell exterior takes the knocks that soft luggage absorbs, and the interior is hydration pack compatible, so a bladder rides alongside the essentials rather than instead of them.Specifications Four in one convertible design, thigh, sling, waist and chest Capacity 5 litres Dimensions 27 x 7 x 29 cm Two compartments Hard shell construction Hydration pack compatible Secure fit during riding Developed with Vantora Available in six colours. Get in touch if you would like help choosing.

Read more less

A focused beam, a longer nightThe Outlander is a 3.5 inch auxiliary light built around a dual projector optic. Where a reflector scatters light, a projector collects it and places it, so the 12,000 lumens on offer land on the road ahead instead of the hedgerow beside it. Useful throw reaches roughly 450 metres.An integrated daytime running light keeps the motorcycle visible in traffic, and the low and high beam patterns cover the shift from town to open highway.The body is die cast aluminium with IP68 sealing, rated from -40°C to +80°C, using 3535 LED chips at 6000K.Specifications 3.5 inch dual projector LED Integrated daytime running light 110W total power, 55W per light 12,000 lumens Throw to approximately 450 metres at 1 lux 6000K pure white output Premium 3535 LED chips IP68 waterproof and dustproof Die cast aluminium housing Operating voltage 9V to 30V Operating temperature -40°C to +80°C Get in touch for fitment guidance on your motorcycle.

Read more less

Light that keeps pace with the roadThe Valkyrie is a 4.5 inch auxiliary light built for riders who cover ground after dark. A 120W dual reflector system produces 13,200 lumens at 6000K, throwing a usable beam well beyond the reach of a standard headlight, so a corner arrives with warning rather than surprise.High beam, low beam and an amber DRL switch from the handlebar, letting a single pair serve the night highway, the trail and the daytime commute.The housing is die cast aluminium, sealed to IP68 and rated from -40°C to +80°C. It is built to come through monsoon touring and Himalayan cold without a change in output.Specifications 4.5 inch dual reflector LED 120W total power 13,200 lumens 6000K pure white output High beam, low beam and amber DRL IP68 waterproof and dustproof Die cast aluminium housing Operating voltage 9V to 30V Operating temperature -40°C to +80°C Supplied as a pair with wiring harness and switch Get in touch for fitment guidance on your motorcycle.

Read more less

Icer 181600-703 is a rear-axle brake pad set for the Audi / VW A6 (2004 - 2011) / passat B6, using the Icer compound, a Spanish-made pad from Europe's largest independent friction manufacturer and an OE supplier to European carmakers.Icer characteristics Manufacturer Icer Brakes, Spain, founded 1961 OE status Tier 1 and Tier 2 supplier to European carmakers Intended use Everyday road driving Approval ECE R90 compliant Quality system AENOR certified Fitment guidanceListed against the Audi / VW A6 (2004 - 2011) / passat B6. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the rear axle. One set covers both wheels on the axle.Compound characteristics as published by Icer.

Read more less

Pagid T3025N is a front-axle brake pad set for the Mitsubishi Pajero Classic, using the Pagid OEM compound, an OE-quality replacement pad from an original-equipment supplier.Pagid OEM characteristics Intended use Everyday road driving Equivalence OE-quality replacement Heritage Pagid is an OE brake supplier to European manufacturers Fitment guidanceListed against the Mitsubishi Pajero Classic. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by Pagid.

Read more less

Pagid T1654N is a front-axle brake pad set for the Chevrolet / Maruti Suzuki Forester / Scross, using the Pagid OEM compound, an OE-quality replacement pad from an original-equipment supplier.Pagid OEM characteristics Intended use Everyday road driving Equivalence OE-quality replacement Heritage Pagid is an OE brake supplier to European manufacturers Fitment guidanceListed against the Chevrolet / Maruti Suzuki Forester / Scross. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by Pagid.

Read more less

Icer 182112 is a front-axle brake pad set for the Audi / Porsche Q5 (2013 onwards) / Macan 4 cylinder petrol, using the Icer compound, a Spanish-made pad from Europe's largest independent friction manufacturer and an OE supplier to European carmakers.Icer characteristics Manufacturer Icer Brakes, Spain, founded 1961 OE status Tier 1 and Tier 2 supplier to European carmakers Intended use Everyday road driving Approval ECE R90 compliant Quality system AENOR certified Fitment guidanceListed against the Audi / Porsche Q5 (2013 onwards) / Macan 4 cylinder petrol. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by Icer.

Read more less

Icer 181369-701 is a front-axle brake pad set for the Mercedes W203, using the Icer compound, a Spanish-made pad from Europe's largest independent friction manufacturer and an OE supplier to European carmakers.Icer characteristics Manufacturer Icer Brakes, Spain, founded 1961 OE status Tier 1 and Tier 2 supplier to European carmakers Intended use Everyday road driving Approval ECE R90 compliant Quality system AENOR certified Fitment guidanceListed against the Mercedes W203. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by Icer.

Read more less

Icer 182103 is a front-axle brake pad set for the Audi A8 3.0 tdi, using the Icer compound, a Spanish-made pad from Europe's largest independent friction manufacturer and an OE supplier to European carmakers.Icer characteristics Manufacturer Icer Brakes, Spain, founded 1961 OE status Tier 1 and Tier 2 supplier to European carmakers Intended use Everyday road driving Approval ECE R90 compliant Quality system AENOR certified Fitment guidanceListed against the Audi A8 3.0 tdi. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by Icer.

Read more less

Pagid T1366N is a rear-axle brake pad set for the BMW 5 SERIES E60 (2003- 2010), using the Pagid OEM compound, an OE-quality replacement pad from an original-equipment supplier.Pagid OEM characteristics Intended use Everyday road driving Equivalence OE-quality replacement Heritage Pagid is an OE brake supplier to European manufacturers Fitment guidanceListed against the BMW 5 SERIES E60 (2003- 2010). Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the rear axle. One set covers both wheels on the axle.Compound characteristics as published by Pagid.

Read more less

Pagid T1444N is a front-axle brake pad set for the MINI Cooper F55 / F56 (2013 -) Diesel, using the Pagid OEM compound, an OE-quality replacement pad from an original-equipment supplier.Pagid OEM characteristics Intended use Everyday road driving Equivalence OE-quality replacement Heritage Pagid is an OE brake supplier to European manufacturers Fitment guidanceListed against the MINI Cooper F55 / F56 (2013 -) Diesel. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by Pagid.

Read more less

Icer 182212 is a front-axle brake pad set for the Mercedes C Class W205 (2015 - ) C220cdi and petrol / E CLASS W213 E200, using the Icer compound, a Spanish-made pad from Europe's largest independent friction manufacturer and an OE supplier to European carmakers.Icer characteristics Manufacturer Icer Brakes, Spain, founded 1961 OE status Tier 1 and Tier 2 supplier to European carmakers Intended use Everyday road driving Approval ECE R90 compliant Quality system AENOR certified Fitment guidanceListed against the Mercedes C Class W205 (2015 - ) C220cdi and petrol / E CLASS W213 E200. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Compound characteristics as published by Icer.

Read more less