ON SALE | Rawtorque

Brembo P34007 is a front-axle brake pad set for the Chevrolet & Isuzu, measuring 152 mm wide and 61 mm tall.Brembo Prime pads are OE-matched for braking performance, low noise and comfort on the road.Specification Width 152 mm Thickness 17 mm Height 61 mm Braking system Akebono WVA number 25151,25150,25149 FMSI D1677 8906 Wear indicator Acoustic Accessories With accessories With anti-squeal shim Axle Front EAN code 8020584104927 These pads are prepared for a wear indicator. If your car uses an electronic wear sensor, the sensor is a separate part and is normally replaced at the same time as the pads.Fitment guidanceListed against the Chevrolet & Isuzu. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

The NGK SILZKR7C11S is the laser iridium spark plug NGK India specifies for the Honda Civic i-VTEC 1.8 and CR-V i-VTEC 2.0. It is a direct, like-for-like replacement. The iridium fine-wire centre electrode gives smoother idle, cleaner combustion and better cold starts, with a service life well beyond a conventional nickel plug. Fitment guidance Honda Civic i-VTEC 1.8L Honda CR-V i-VTEC 2.0L Honda's plug range is easy to get wrong. The earlier Civic 1.6, 1.8i and 2.0i take the IZFR6K-11S. The Accord 2.4 from 2008 and CR-V 2.4 take the ILZKR7B-11S. Message us with your model, variant and year and we will confirm before you order. Both are four-cylinder, so a full change takes four plugs. Specifications Brand: NGK Part Number: SILZKR7C11S Type: Laser Iridium Heat Range: 7 Sold as: Pack of 4 Fitting noteSupplied pre-gapped. If you check the gap, move only the outer ground electrode. Thread in by hand, then torque to your service manual figure.

Read more less

Rolon BPR brass-plated sealed chain and sprocket kit for the TVS Apache RTR 200 4V. Supplied as a complete drivetrain set, matched to OE gearing.What's in the kit Brass-plated sealed chain R520HPORC-116-2 Front sprocket 13T (S 01 806), 2 holes Rear sprocket 45T (S 01 804), 4 holes Rolon kit reference HPORC 332 Why the BPR kit Quadruple-sealed ring construction holds factory grease in and grit out Brass plating for corrosion resistance and a lasting gold finish Rubberised front sprocket damps drivetrain noise and acts as a damper Hardened sprocket teeth for wear resistance and fatigue strength Chain and sprockets wear together and should always be replaced as a set. Message us for fitment guidance if you are unsure which model year you have.

Read more less

V Strom Vambrace Bashplate – Engine Protection for Suzuki V Strom The V Strom Vambrace Bashplate from Legundary is designed to provide added protection to the lower engine and underbody area of the Suzuki V Strom. Built to shield key components from road debris, uneven terrain, and unexpected surface contact, this bashplate enhances mechanical protection without compromising ground clearance or overall styling. Engine guards and bashplates play a critical role when riding through mixed terrain, speed breakers, gravel roads, or rough patches. Positioned beneath the engine, this bashplate acts as a defensive barrier against stones, debris, and underbody impact. Its compact design allows strong coverage while maintaining the motorcycle’s structural balance. Manufactured using mild steel and finished in black, the Vambrace Bashplate combines strength with durability to support both touring and everyday riding conditions. Designed for Suzuki V Strom The Vambrace Bashplate is engineered specifically for the Suzuki V Strom, ensuring: • Direct compatibility with the motorcycle’s frame• Secure mounting alignment• Protection for critical underbody engine areas• Maintained ground clearance Its model-specific design ensures proper integration without requiring structural modification. Functional Engine Protection Underbody exposure is common during: • Rough road riding• Speed breaker crossings• Gravel and uneven terrain• Off-road or adventure touring This bashplate provides a protective layer beneath the engine casing to help reduce potential impact damage. Its extended coverage design offers improved protection compared to smaller underguards. The plate is built to remain firm during riding while supporting engine protection in everyday scenarios. Mild Steel Construction & Finish Constructed from mild steel, the bashplate delivers: • Strong structural durability• Reliable impact resistance• Corrosion resistance through surface treatment• Stable underbody support The smooth black finish adds a refined look while complementing the V Strom’s rugged aesthetic. Product Specifications • Material: Mild Steel• Colour: Black• Dimensions: 36 × 24 × 12 cm (L × B × H)• Weight: 1.775 kg The balanced weight ensures effective protection without excessive additional load. Features • Designed for long-lasting durability• Provides extended engine coverage• Made of mild steel for strong protection• Smooth, refined finish• Surface-treated components for corrosion resistance This bashplate enhances underbody protection while maintaining the motorcycle’s riding dynamics.

Read more less

Why Choose the Legundary Back Rest with Carrier for Hunter 350? The Legundary Back Rest with Carrier is designed specifically for the Royal Enfield Hunter 350, combining pillion back support with a rear luggage mounting platform in a single structure. This is a model-specific component engineered for the Hunter 350 and is not listed as universal fitment. Model-Specific Compatibility – Royal Enfield Hunter 350 Designed exclusively for Royal Enfield Hunter 350 Structured to align with factory mounting points Intended for direct installation Integrated backrest and carrier design Compatibility beyond Hunter 350 is not stated and should not be assumed. Material & Construction Constructed from Mild Steel Backrest finished with Foam and Rexine Powder-coated black finish Designed for durability and corrosion resistance Material thickness is not specified in the official listing. Dimensions & Weight Dimensions: 40 x 28 x 29 cm (L x B x H) Product Weight: 3.100 kg Color: Black Dual Function Design This unit integrates: 1️⃣ Pillion Back Support Foam-cushioned backrest Rexine covering Intended to improve pillion comfort during rides 2️⃣ Rear Carrier Platform Metal base for luggage mounting Suitable for light luggage or top box (compatibility to be verified before purchase) Load capacity is not specified in the listing and should be confirmed before heavy-duty usage. Intended Use Suitable for: Touring riders Riders carrying pillion passengers Daily commuting with luggage Mounting soft bags or top boxes Installation Designed for direct mounting on Hunter 350 Professional installation recommended for proper torque and alignment Product Specifications Brand: Legundary Product Name: Back Rest with Carrier Motorcycle Compatibility: Royal Enfield Hunter 350 Material: Mild Steel + Foam + Rexine Finish: Black Dimensions: 40 x 28 x 29 cm Weight: 3.100 kg

Read more less

The Maddog 4-Wheeler Wireharness brings Maddog's proven plug-and-play reliability to cars. Designed specifically for four-wheeler auxiliary light installation, this kit includes both the harness and the switch in a single bundle — so you're ready to install from the moment the box opens.Built on the same 100% pure copper, automotive-grade wiring platform as the bike harnesses, but configured for car voltage systems and mounting requirements.Kit Contents: 4-Wheeler Wireharness Switch

Read more less

The NGK ILZKR6Q11 is the laser iridium spark plug NGK India specifies for the current 1.5 litre K15C petrol engine used across Maruti Suzuki and its Toyota-badged siblings. It is a direct, like-for-like replacement. The fine-wire iridium centre electrode fires a tighter, more focused spark than a conventional plug. In everyday driving that means easier cold starts, a steadier idle and cleaner combustion, with a service life well beyond a nickel plug because iridium holds its gap. Fitment guidance Per NGK India's current application chart, ILZKR6Q11 is listed for: Maruti Suzuki Brezza 1.5L Ertiga 1.5L Grand Vitara 1.5L XL6 1.5L Victoris 1.5L Toyota Urban Cruiser Hyryder 1.5L Rumion 1.5L Not the same as the older K15B. If your Ertiga, Ciaz, XL6, S-Cross or Jimny runs the earlier K15B engine, NGK does not list an iridium plug for it. Message us with your model and year and we will tell you what does fit. The K15C is a four-cylinder, so a full change takes four plugs. Specifications Brand: NGK Part Number: ILZKR6Q11 Type: Laser Iridium Centre Electrode: Iridium fine-wire Heat Range: 6 Engine: Maruti K15C 1.5L Sold as: Pack of 4 Fitting note Supplied pre-gapped. If you check the gap, move only the outer ground electrode. The iridium centre electrode is a fine wire and will break if levered against. Thread in by hand first, then torque to the figure in your service manual.

Read more less

The NGK SILZKR7B-11 is the laser iridium spark plug NGK India specifies for the Hyundai Elantra 1.8 Beta and Tucson 2.0 Theta. It is a direct, like-for-like replacement. The iridium fine-wire centre electrode gives smoother idle, cleaner combustion and better cold starts, and holds its gap far longer than a nickel plug. Fitment guidance Hyundai Elantra 1.8L Beta (model years 2012 to 2016) Hyundai Tucson 2.0L Theta This is not the Kappa plug. If you run the 1.2 Kappa in a Grand i10, Xcent, i20 or Aura, that takes the LKR7BIX-P. The 1.0 and 1.4 turbo petrols take the ILKR9Q7G. Message us with your engine and year if you are unsure. Both are four-cylinder, so a full change takes four plugs. Specifications Brand: NGK Part Number: SILZKR7B-11 Type: Laser Iridium Heat Range: 7 Sold as: Pack of 4 Fitting noteSupplied pre-gapped. If you check the gap, move only the outer ground electrode. Thread in by hand, then torque to your service manual figure.

Read more less

Why Choose the Legundary Halter Saddle Stay for Hunter 350? The Legundary Hunter Halter Saddle Stay is designed specifically for the Royal Enfield Hunter 350, providing side support for saddle bags to prevent inward sagging and contact with the wheel. This saddle stay is engineered for the Hunter 350 platform and is not listed as universal fitment. Model-Specific Compatibility – Royal Enfield Hunter 350 Designed exclusively for Royal Enfield Hunter 350 Structured side mounting design Direct-fit installation Engineered to align with factory mounting points Compatibility beyond Hunter 350 is not mentioned and should not be assumed. Material & Construction Constructed from Mild Steel Powder-coated finish Designed for durability and corrosion resistance Built using high-quality mild steel tubing Material thickness is not specified in the official listing. Dimensions & Weight Dimensions: 50 x 38 x 7 cm (L x B x H) Weight: 2.300 kg Color: Black Functional Design The Halter Saddle Stay is intended to: Provide side support for saddle bags Prevent luggage from sagging toward the wheel Maintain bag positioning during long rides Improve luggage stability This structure supports safe mounting of soft saddle bags. Top box compatibility is not implied. Intended Use Suitable for: Touring riders Long-distance travel Daily commuting with side luggage Riders using soft saddle bags Load capacity is not specified in the listing and should be verified before heavy-duty usage. Installation Designed for direct mounting on Hunter 350 Professional installation recommended for proper alignment and torque settings Product Specifications Brand: Legundary Product Name: Hunter Halter Saddle Stay Motorcycle Compatibility: Royal Enfield Hunter 350 Material: Mild Steel Finish: Black Dimensions: 50 x 38 x 7 cm Weight: 2.300 kg

Read more less

Designed for Royal Enfield Super Meteor 650 The Legundary (LCB) Super Meteor 650 Combat Bash Plate is developed specifically for the Royal Enfield Super Meteor 650. This bash plate is designed to provide lower engine protection against road debris, uneven surfaces, and minor impacts encountered during regular riding conditions. This is not listed as a universal fitment product. Model Compatibility Compatible with: Royal Enfield Super Meteor 650 Direct fitment as per manufacturer design No cross-model compatibility claimed Material & Finish Material: Aluminium Color: Silver Aluminium construction offers a balance of strength and weight efficiency. Dimensions & Weight Dimensions: 49 x 22 x 19 cm (L x B x H) Weight: 0.966 kg Functional Purpose The Combat Bash Plate is intended to: Provide protective coverage for the lower engine area Reduce exposure to stones, debris, and uneven surfaces Add structural underbody protection Integrate with the motorcycle’s lower chassis profile This product is not described as impact-proof or crash-rated for high-speed collisions. Installation Direct mounting design Engineered specifically for Super Meteor 650 Professional installation recommended for correct alignment and torque Product Specifications Brand: Legundary (LCB) Product Name: Super Meteor 650 Combat Bash Plate Motorcycle Compatibility: Royal Enfield Super Meteor 650 Material: Aluminium Finish: Silver Dimensions: 49 x 22 x 19 cm Weight: 0.966 kg

Read more less

Triumph Scrambler 400 X Vector Radiator Grill Silver – Legundary Aluminium Guard Product Description The Triumph Scrambler 400 X Vector Radiator Grill Silver from Legundary is designed specifically for the Triumph Scrambler 400 X. This radiator guard is built to provide frontal coverage for the radiator area while maintaining airflow through a precision-cut grill structure. Constructed from aluminium and finished in silver, the design follows the Scrambler 400 X’s front-end layout. The grill pattern is engineered to allow airflow while adding a protective barrier against stones, debris, and road elements encountered during riding. The Triumph Scrambler 400 X Vector Radiator Grill Silver measures 500 x 290 x 130 mm and has a listed weight of 0.96 kg. It is developed as a model-specific fitment and is positioned as an easy bolt-on installation without major modifications. For riders looking to add a dedicated radiator protection accessory to the Triumph Scrambler 400 X, this Legundary Vector Radiator Grill Silver provides a direct-fit aluminium solution aligned with the motorcycle’s styling and mounting points. Specifications Brand: Legundary Product Type: Radiator Grill / Radiator Guard Motorcycle Compatibility: Triumph Scrambler 400 X Material: Aluminium Finish: Silver Dimensions: 500 x 290 x 130 mm Weight: 0.96 kg Installation: Easy bolt-on

Read more less

Royal Enfield Bear 650 Gopher Luggage Carrier – Legundary Mild Steel Rear Carrier Product Description The Royal Enfield Bear 650 Gopher Luggage Carrier from Legundary is designed specifically for the Royal Enfield Bear 650. This rear carrier is built to provide a structured mounting platform for luggage during daily use and long-distance riding. Constructed from mild steel and finished in black, the carrier features a metal base plate designed to support mounted luggage. The structure allows riders to secure duffel bags, soft luggage, or mount a carrier plate for compatible top boxes. The layout is developed to align with the Royal Enfield Bear 650 frame geometry for proper fitment. The Royal Enfield Bear 650 Gopher Luggage Carrier measures 38 x 32 x 13 cm and has a listed weight of 1.74 kg. It is described as an easy-install component and can be removed when not required. The design focuses on providing a stable rear mounting surface for luggage. For riders seeking a dedicated rear luggage mounting solution for the Royal Enfield Bear 650, this Legundary Gopher Luggage Carrier provides a model-specific mild steel platform. Specifications Brand: Legundary Product Type: Luggage Carrier Motorcycle Compatibility: Royal Enfield Bear 650 Material: Mild Steel Finish: Black Dimensions: 38 x 32 x 13 cm Weight: 1.74 kg Installation: Easy Installation

Read more less

Moto Torque Air Filter for Royal Enfield Interceptor 650, Continental GT 650 & Bear 650 The Moto Torque Performance Air Filter is precision-built for Royal Enfield Interceptor 650, Continental GT 650, and Bear 650 motorcycles. Designed for twin-cylinder performance platforms, this air filter enhances intake airflow while maintaining filtration integrity for consistent engine performance. Engineered to meet the demands of Royal Enfield 650cc motorcycles, the filter supports improved combustion efficiency, throttle response, and long-term riding performance across city, highway, and touring conditions. Designed for Royal Enfield 650 Platform • Royal Enfield Interceptor 650• Royal Enfield Continental GT 650• Royal Enfield Bear 650• Twin-cylinder 650 engine compatibility Model-specific fitment ensures structural precision and consistent sealing within the airbox. Engineered Features 4-Layer High-Flow Cotton GauzeConstructed with four layers of precision-woven cotton gauze to improve intake flow while maintaining filtration integrity. Supports optimized combustion and sustained power output. Multi-Stage Filtration EfficiencyCaptures fine dust, debris, and airborne contaminants without restricting airflow. Designed for varied riding environments including urban traffic and open highways. Reusable & Serviceable DesignBuilt for longevity and sustainability. The filter can be cleaned, re-oiled, and reused — reducing replacement frequency and maintenance costs. Heat-Resistant & Structurally ReinforcedEngineered to withstand elevated temperatures and vibration stress typical of twin-cylinder engines. Enhanced Throttle Response & Engine EfficiencyBy reducing intake resistance, the filter promotes smoother throttle input, cleaner combustion, and improved fuel efficiency. Performance Profile by Motorcycle Royal Enfield Interceptor 650Supports smoother torque delivery and consistent cruising performance. Royal Enfield Continental GT 650Designed to complement aggressive acceleration and high-rev responsiveness. Royal Enfield Bear 650Reinforces airflow stability and engine endurance for long-haul touring. Specifications • Brand: Moto Torque• Product Type: Performance Air Filter• Compatibility: Interceptor 650 / Continental GT 650 / Bear 650• Construction: 4-Layer Cotton Gauze• Design: Reusable & Serviceable• Engine Type: Twin-Cylinder 650cc

Read more less

The Maddog Switch and Wire Harness Pro is the next-generation control solution for riders who want clean, clutter-free auxiliary light installation. The Switch Pro combines pass function, on/off control, and beacon mode in a single smart soft-push button, and comes pre-bundled with the Wire Harness Pro for true plug-and-play setup right out of the box.The Wire Harness Pro uses a solid state relay protected circuit with IP-67 waterproof and dustproof rating — so it handles monsoon riding without hesitation. 100% pure copper terminals with tin coating ensure reliable conductivity over time.Compatibility note: Works exclusively with the Wire Harness Pro included in the kit. Not compatible with the standard Maddog Wire Harness, older Wire Harness Pro versions, or any third-party harnesses.Kit Contents: Switch Pro Wire Harness Pro 1× Handlebar clamp 2× Mirror mounting clamps Warranty card Screw set 4× Silicon belts

Read more less

Precision Ignition Upgrade for the Royal Enfield Himalayan 410 The NGage High Performance Spark Plug Kit is engineered to improve ignition efficiency on the Royal Enfield Himalayan 410 and Scram platform. This is not just a plug replacement, it is a complete ignition upgrade designed for smoother, cleaner and more responsive performance. ⚡ Improved Combustion Efficiency Combining a genuine NGK Iridium IX spark plug with an ultra low-resistance racing cable and a resistor spark cap, the kit delivers: Better spark consistency Cleaner, more complete combustion Reduced misfires 🧠 Smoother, More Responsive Engine Improved throttle response Better acceleration feel More stable idle 🌧️ Reliable in All Conditions Easier cold starts Reliable ignition in wet weather Consistent performance in daily and touring use 🏁 Built for Street & Performance Use Compatible with stock and modified setups Suitable for both BS4 and BS6 motorcycles Limited warranty, designed for a service life up to 1,00,000 km ✅ Fitment This kit is designed for the following Royal Enfield models: Himalayan 410 Scram 411 Scram 440 📦 WHAT'S INCLUDED NGK Iridium IX Spark Plug (CR8EIX, made in India): 1 No NGage Resistor Spark Cap (SD05F-R, 5kΩ): 1 No NGage Racing Spark Plug Cable, ultra low resistance: 1 No

Read more less

Precision Ignition Upgrade for the Royal Enfield J-Platform 350 The NGage High Performance Spark Plug Kit is engineered to improve ignition efficiency on the Royal Enfield J-series 350 engine. This is not just a plug replacement, it is a complete ignition upgrade designed for smoother, cleaner and more responsive performance. ⚡ Improved Combustion Efficiency Combining an NGage Double Iridium spark plug with an ultra low-resistance racing cable and a resistor spark cap, the kit delivers: Better spark consistency Cleaner, more complete combustion Reduced misfires 🧠 Smoother, More Responsive Engine Improved throttle response Better acceleration feel More stable idle 🌧️ Reliable in All Conditions Easier cold starts Reliable ignition in wet weather Consistent performance in daily and touring use 🏁 Built for Street & Performance Use Compatible with stock and modified setups Suitable for both BS4 and BS6 motorcycles Limited warranty, designed for a service life up to 1,00,000 km ✅ Fitment This kit is designed for the following Royal Enfield J-platform 350 models: Meteor 350 Reborn Classic 350 Hunter 350 Bullet 350 (Reborn) Goan Classic 350 📦 WHAT'S INCLUDED NGage Double Iridium Spark Plug (DH7RTII-8, made in Japan): 1 No NGage Resistor Spark Cap (CB05F-R, 5kΩ): 1 No NGage Racing Spark Plug Cable, ultra low resistance: 1 No

Read more less

Moto Torque Performance Air Filter for Royal Enfield Classic 350, Hunter 350 & Meteor 350 The Moto Torque Performance Air Filter for Classic 350, Hunter 350 & Meteor 350 is designed specifically for Royal Enfield’s 350cc J-series platform. Built as a direct replacement air filter, it is engineered to support consistent airflow and filtration for everyday riding conditions. This air filter uses a 4-layer high-flow cotton gauze construction, designed to allow air intake while maintaining filtration integrity. The multi-stage filtration design helps capture dust, dirt, and airborne contaminants without restricting airflow, supporting stable engine operation. The filter is built as a reusable and serviceable unit, allowing cleaning and reinstallation instead of frequent replacements. This helps maintain consistent performance over time while reducing maintenance requirements. Designed for regular riding environments, the Moto Torque air filter for Classic 350, Hunter 350 and Meteor 350 is constructed to handle heat and vibration associated with single-cylinder engines. The air filter is compatible with Royal Enfield motorcycles using the J-series 350 platform and installs as a direct replacement without modification. Specifications Brand: Moto TorqueCompatibility: Royal Enfield 350cc J-SeriesFilter Type: High-flow air filterFilter Material: Cotton gauze (4-layer)Design: Multi-stage filtrationReusable: Yes (washable and reusable)Installation: Direct replacement

Read more less

N-Gage Hyper Flow Air Filter for Royal Enfield J-Platform 350 (Classic 350 / Meteor 350 / Hunter 350) The N-Gage Hyper Flow Air Filter for Royal Enfield J-Platform 350 is a performance-oriented replacement air filter crafted specifically for Royal Enfield motorcycles built on the J-platform. This includes popular models like the Classic 350, Meteor 350, and Hunter 350. Designed as a direct stock replacement, it boosts airflow efficiency while maintaining dependable filtration for everyday riding conditions. This Royal Enfield air filter ensures your engine breathes freely without compromising protection. Modern BS6 motorcycles depend on a precise air–fuel balance to offer smooth throttle response, consistent combustion, and long-term engine stability. The air filter plays a crucial role in this system, controlling both the volume and cleanliness of intake air entering the engine. The N-Gage Hyper Flow Air Filter improves intake airflow compared to standard disposable paper filters, while protecting the engine from dust, debris, and moisture. This is especially important for Indian riding environments where conditions can be harsh and unpredictable. Royal Enfield Air Filter with High-Flow Cotton Gauze Construction This Royal Enfield air filter is built using premium organic cotton gauze, layered and specially treated to allow greater airflow without sacrificing filtration performance. Unlike conventional paper filters, which restrict airflow over time as they collect dirt, cotton gauze filters maintain more consistent airflow when cleaned. Proper maintenance ensures longevity and consistent engine protection. The filter arrives factory pre-oiled, which helps trap fine dust particles effectively while still allowing increased air volume. This balance between airflow and filtration is essential for stable engine performance in all riding conditions, from stop-and-go city traffic to extended highway cruises. Designed Specifically for Royal Enfield J-Platform 350cc Engines The N-Gage Hyper Flow Air Filter fits precisely within the stock airbox of Royal Enfield’s J-platform 350cc engines. It installs as a direct replacement with no cutting, drilling, trimming, or modification needed. This makes upgrading your motorcycle’s filter simple and hassle-free. This air filter matches factory dimensions and mounting points, integrating seamlessly with the original intake system. This means riders can improve airflow without changing the motorcycle’s stock intake layout, sealing, or weather protection. These features enhance the bike’s reliability during daily use in varying conditions. Throttle Response and Ride Feel with the N-Gage Royal Enfield Air Filter Improved airflow contributes to smoother throttle response and more consistent power delivery across all rpm ranges. Many riders choose high-flow air filters to reduce intake restriction and help the engine breathe freer during acceleration and steady cruising. This Royal Enfield air filter is designed for riders seeking enhanced ride feel without complex modifications. According to manufacturer specifications, this air filter offers performance gains of up to 0.5 BHP under optimal conditions. However, real-world results may vary based on factors like riding style, maintenance habits, fuel quality, and overall engine condition. The filter works perfectly with the stock ECU and exhaust system and requires no ECU remapping or tuning adjustments. Reusable and Long-Term Ownership Benefits Unlike disposable paper filters that need frequent replacement, this N-Gage air filter is washable and reusable. Regular cleaning and re-oiling using appropriate maintenance products allow multiple reuses across the filter’s lifespan. This makes it an eco-friendly and cost-effective solution for riders. Choosing this filter supports long-term ownership goals, reducing consumable waste and maintaining consistent performance over time. Regular maintenance is vital to ensure continuous filtration efficiency and engine protection, especially in dusty or high-usage scenarios commonly faced by riders. Built for Real-World Indian Riding Conditions with the Royal Enfield Air Filter Indian roads often present challenges such as high dust levels, humidity, heavy monsoon rain, and temperature swings. The N-Gage Hyper Flow Air Filter is engineered to deliver consistent filtration across dust and rain conditions, making it ideal for daily commutes, highway tours, and mixed-use riding. This filter is compatible with BS6, Euro 4, and Euro 5 compliant models, meeting current emission norms while focusing equally on airflow efficiency and intake cleanliness. These attributes ensure your motorcycle maintains top performance while adhering to environmental regulations. Installation and Maintenance Guidance Installation of the filter follows the exact procedure as replacing a standard stock air filter and requires no special tools or technical know-how. Riders should follow recommended service intervals for inspection, cleaning, and re-oiling to maintain optimal performance and filtration consistency throughout the filter’s lifespan.

Read more less

Let Your Himalayan Breathe Better The Ngage Hyper Flow Air Filter for Royal Enfield Himalayan 411 and Scram 411 is engineered to improve intake airflow while maintaining effective filtration. Designed as a direct replacement for the OEM paper element, this high-flow cotton gauze filter supports sharper throttle response and cleaner engine breathing across varied riding conditions. Built for riders who tour long distances, commute daily, or tackle mixed terrain, the Hyper Flow filter combines performance-focused airflow with long-term durability and reusability. This is not a disposable consumable. It’s a serviceable intake upgrade designed for sustained performance. High-Flow Cotton Gauze Construction The filter element is constructed from 100% organic cotton gauze layered within a reinforced mesh structure. Cotton gauze media is designed to: Allow increased airflow compared to standard paper filtersSupport smoother intake efficiencyMaintain filtration performance when properly maintainedOperate effectively across dusty and mixed riding conditions The multi-layer structure balances air volume with particle trapping capability. According to manufacturer specification, airflow improvement can be up to 30% compared to stock filters. Actual results may vary depending on riding environment and maintenance. Performance Characteristics The Ngage Hyper Flow Air Filter is designed to support improved engine breathing. Manufacturer-indicated performance data includes: Up to 0.9 BHP increase under controlled conditionsSharper throttle responseImproved intake efficiency Performance gains depend on engine condition, riding environment, and overall motorcycle setup. The filter is dyno-tested as per manufacturer material; however, real-world output may vary between motorcycles. Reinforced Structural Support The Hyper Flow unit incorporates reinforced internal support pillars. These support structures are designed to: Maintain filter shape under airflow pressureResist deformation at higher temperaturesProvide durability across long-haul riding Structural reinforcement ensures consistent seating inside the OEM airbox. Washable & Reusable Design Unlike disposable paper filters, the Hyper Flow filter is washable and reusable. Serviceable design supports: Reduced long-term replacement costLower environmental wasteExtended service life with proper maintenance When cleaned and re-oiled at recommended intervals, the filter is intended to maintain stable performance. Proper maintenance is essential for filtration efficiency and engine health. Optional recharge oil is available separately. Direct OEM Replacement Fitment The Ngage Hyper Flow Air Filter is designed as a plug-and-play replacement for the factory airbox. Fitment details: No cutting requiredNo modification requiredInstalls into OEM airboxMaintains stock intake geometry This allows easy installation while preserving the motorcycle’s original intake structure. Fitment Compatibility Compatible With: Royal Enfield Himalayan 411Royal Enfield Scram 411 Applicable for: BS4 modelsBS6 modelsEuro 4 compliant unitsEuro 5 compliant units Compatibility is limited strictly to Himalayan 411 and Scram 411 platforms. Not compatible with Himalayan 450 or other Royal Enfield models. Durability in Real-World Conditions The filter is engineered to withstand: High ambient temperaturesDust-heavy ridingMountain terrainLong-distance touring Cotton gauze construction and reinforced framing support durability under varied riding stress. Lifetime Warranty Coverage As per manufacturer specification, the Hyper Flow filter includes lifetime warranty coverage up to 1,00,000 km, subject to proper maintenance and usage conditions. Warranty terms are governed by the manufacturer. What’s in the Box 1 × Ngage Hyper Flow Air FilterCleaning & Recharging Instructions (PDF Available)Optional Recharge Oil (Add-on) Technical Specifications Brand: NgageProduct Type: Performance Air FilterFilter Media: 100% Organic Cotton GauzePre-Oiled: Yes (Factory Pre-Oiled)Performance Claim: Up to 0.9 BHP (manufacturer indicated)Airflow Improvement: Up to 30% (manufacturer indicated)Maintenance: Washable & ReusableFitment: Himalayan 411 / Scram 411Installation: Direct OEM Replacement Important Notes Ensure proper cleaning and re-oiling at recommended intervals.Do not operate without proper oiling after washing.Performance gains may vary depending on motorcycle condition.Confirm model compatibility before purchase. Summary The Ngage Hyper Flow Air Filter for Royal Enfield Himalayan 411 and Scram 411 is a reusable cotton gauze intake upgrade designed to improve airflow, support throttle response, and provide long-term durability. With reinforced structural support, direct OEM fitment, and washable construction, it offers a performance-focused alternative to disposable stock filters while maintaining practical serviceability. Improved airflow. Serviceable design. Built for Himalayan terrain.

Read more less

Aluminium Engine Protection Upgrade for Royal Enfield Himalayan 450 The LCB Vambrace Bash Plate in Aluminium for Royal Enfield Himalayan 450 is engineered to protect the motorcycle’s most exposed mechanical components during serious adventure use. Designed and manufactured by Legundary Custom Builds, this precision-built aluminium bash plate shields the engine casing, lower frame rails, and vulnerable underbody areas from impact damage caused by rocks, debris, ruts, and uneven terrain. Adventure motorcycles are built for unpredictable environments. However, factory underbody protection is often minimal. Once you begin tackling rocky trails, broken tarmac, water crossings, or loose gravel, the engine sump and lower frame become high-risk impact zones. The Vambrace Bash Plate reinforces this critical area through structural aluminium shielding without compromising ride dynamics. Built for Impact Absorption Manufactured from high-grade aluminium, the Vambrace Plate offers a strong yet lightweight protective barrier. Aluminium is selected for its excellent strength-to-weight ratio and natural corrosion resistance. Unlike heavier steel alternatives, aluminium reduces unnecessary front-end weight while still delivering substantial impact resistance. This ensures: Protection against stone strikes Defense from debris impact Reduced risk of sump damage Shielding of frame underbody sections Impact absorption is distributed across the plate’s reinforced surface rather than concentrated at a single stress point. Lightweight Protection That Preserves Handling Weight distribution matters on an adventure motorcycle. Excessive weight at the lower front section affects steering feedback and suspension response. The Vambrace Aluminium Bash Plate is designed to add structural protection without altering the Himalayan 450’s balance. Benefits of aluminium construction include: Lower overall mass compared to steel Reduced unsprung load influence Preserved suspension performance Improved maneuverability during off-road riding Protection should not compromise agility. This plate is built with that principle in mind. Engineered for Cooling and Clearance A properly designed bash plate must not restrict airflow or reduce ground clearance. The Vambrace Plate maintains adequate ventilation channels to support cooling efficiency while protecting the engine casing. It preserves: Ground clearance for obstacle navigation Drain access for maintenance Frame geometry alignment Adventure riding demands clearance discipline. The design respects that. Vambrace Structural Design The Vambrace-inspired architecture adds rigidity through controlled bends and reinforcement lines. These structural folds increase stiffness without requiring excessive thickness. This results in: Increased load-bearing strength Reduced plate flex under impact Long-term structural durability The design complements the Royal Enfield Himalayan 450’s rugged adventure styling while serving a clear mechanical purpose. Fitment Notice ⚙️ This bash plate is not compatible with stock lower crash guards. It is designed to mount independently to maintain proper alignment and clearance. Installing it alongside incompatible lower guards may interfere with mounting geometry. Corrosion Resistance and Finish Aluminium naturally resists oxidation better than untreated steel. The surface finish is engineered to withstand: Mud exposure Water crossings Heat cycles Dust and gravel abrasion Adventure accessories must survive environmental stress — not just look prepared for it. Direct Bolt-On Installation Installation remains mechanically clean: No welding No cutting No drilling No structural modification The mounting points align with factory architecture, ensuring secure fitment without frame alteration. This protects: Frame integrity Service accessibility Warranty safety Built for Real-World Riding This is not decorative underbody armor. It is functional engine protection. Ideal for: Trail riding Mountain routes Gravel and broken roads Expedition travel Touring in remote terrain Engine casing damage can immobilize a motorcycle. Preventative protection reduces that risk significantly. Key Features Designed specifically for Royal Enfield Himalayan 450 High-grade aluminium construction Lightweight yet impact-resistant build Protects engine sump and lower frame Maintains ground clearance and airflow Vambrace structural reinforcement design Direct bolt-on installation Not compatible with stock lower crash guards Construction Overview Material: High-Grade AluminiumFinish: Corrosion-Resistant Surface TreatmentFitment: Royal Enfield Himalayan 450Installation: Direct Bolt-OnApplication: Engine & Underbody Protection Why This Upgrade Makes Mechanical Sense Adventure motorcycles operate in impact-prone environments. The engine sump and lower frame sections remain vulnerable without reinforcement. Aluminium bash protection distributes impact energy while maintaining lightweight efficiency. The LCB Vambrace Bash Plate strengthens your Himalayan 450’s survivability without disturbing balance or handling. This is structural protection — not cosmetic armor. Warranty This product includes a 6-month manufacturer warranty from Legundary Custom Builds against manufacturing defects. RawTorque does not provide independent warranties beyond the manufacturer’s coverage. Refer to your Warranty Policy for full details.

Read more less

Brembo P50008 is a front-axle brake pad set for the Mercedes W124, measuring 110 mm wide and 60 mm tall.Brembo Prime pads are OE-matched for braking performance, low noise and comfort on the road.Specification Width 110 mm Thickness 19 mm Height 60 mm Braking system Lucas WVA number 21028,20941 FMSI D423 7311 Wear indicator Prepared for wear indicator Accessories With brake caliper bolts With anti-squeal shim With accessories Axle Front EAN code 8020584053805 These pads are prepared for a wear indicator. If your car uses an electronic wear sensor, the sensor is a separate part and is normally replaced at the same time as the pads.Fitment guidanceListed against the Mercedes W124. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

Rolon BPR brass-plated sealed chain and sprocket kit for the KTM Duke 125 (new model). Supplied as a complete drivetrain set, matched to OE gearing.What's in the kit Brass-plated sealed chain R520HPORC-112-2 Front sprocket 14T (SR 02 249), 2 holes Rear sprocket 45T (S 02 661 with SF), 6 holes Rolon kit reference HPORC 373NF Why the BPR kit Quadruple-sealed ring construction holds factory grease in and grit out Brass plating for corrosion resistance and a lasting gold finish Rubberised front sprocket damps drivetrain noise and acts as a damper Hardened sprocket teeth for wear resistance and fatigue strength Chain and sprockets wear together and should always be replaced as a set. Message us for fitment guidance if you are unsure which model year you have.

Read more less

Minimal. Functional. Built for riders who want luggage capability without added bulk. The MotoCare Pipe Carrier for TVS Apache RTX 300 is a purpose-built rear luggage rack designed to provide a stable and secure mounting platform for your gear. Whether it’s daily essentials or touring luggage, this carrier ensures reliable load support without compromising the motorcycle’s design or balance. 🧱 Model-Specific Engineering Designed exclusively for the Apache RTX 300, ensuring: Precise mounting points Stable load distribution No interference with body panels Clean integration with stock design This is not a universal carrier — it’s built to fit right. 🎒 Practical Luggage Utility Supports: Tail bags Touring luggage Daily commute gear The flat platform design ensures easy strapping and secure placement, making it ideal for both short rides and long-distance touring. ⚙️ Build Quality & Durability High-strength metal construction Rigid mounting structure Designed for load stability under real riding conditions Corrosion-resistant finish for long-term durability Built to handle Indian roads — not just showroom display. 🛠️ Installation & Fitment Direct-fit for Apache RTX 300 No major modification required Professional installation recommended for best alignment 🧠 Real-World Use Case Ideal for: Touring riders Daily commuters carrying essentials Riders wanting a minimal luggage setup Clean builds without bulky accessories 📦 Warranty 1 Year Manufacturer Warranty Note:RawTorque does not provide any additional warranty beyond the manufacturer’s coverage.For complete details, please refer to our warranty policy.

Read more less

Brembo P83064 is a front-axle brake pad set for the Toyota Old Corolla upto 2007, measuring 132 mm wide and 57 mm tall.Brembo Prime pads are OE-matched for braking performance, low noise and comfort on the road.Specification Width 132 mm Thickness 18 mm Height 57 mm Braking system Lucas WVA number 23766,23818,23819 FMSI D1215 8335 Wear indicator Acoustic Accessories With anti-squeal shim Axle Front EAN code 8020584057995 These pads are prepared for a wear indicator. If your car uses an electronic wear sensor, the sensor is a separate part and is normally replaced at the same time as the pads.Fitment guidanceListed against the Toyota Old Corolla upto 2007. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less