Brakes

Brembo P85200 is a front-axle brake pad set from Brembo's Prime range for the Skoda & VW, measuring 148 mm wide, 56 mm tall and 19 mm thick.Prime is Brembo's OE-matched road range. The friction material is specified to match original equipment braking performance, the backplate is painted against corrosion, an anti-squeal shim is included, and the set is ECE R90 type-approved. Brembo lists it as the pad to run with Prime brake discs.This is not the Xtra range, which is Brembo's sport pad line for drilled discs, and not the ceramic (N-suffix) range, which we do not currently stock.Specification Range Brembo Prime Technical content OE-matched Axle Front Width 148 mm Height 56 mm Thickness 19 mm WVA number 26992,26991 Backplate Black, painted Accessories Anti-squeal shim, brake caliper bolts Wear indicator Not built into the pad Approval ECE R90 type-approved EAN code 8020584132852 This set does not have a wear indicator built into the pad. If your Skoda & VW uses an electronic brake wear sensor, that sensor is a separate part and is normally replaced at the same time as the pads.Fitment guidanceListed against the Skoda & VW. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

Brembo L05010 is a fully synthetic DOT 5.1 brake fluid, supplied in a 1 litre bottle.The figures below are the minimums the DOT 5.1 standard itself requires, not measured values for this bottle.Specification Part number L05010 Standard DOT 5.1 Volume 1 litre Type Fully synthetic, glycol ether based Minimum dry boiling point for this standard 260 °C Minimum wet boiling point for this standard 180 °C Brake fluid is hygroscopic, meaning it absorbs moisture from the air over time, and that moisture lowers its boiling point long before the fluid looks dirty. Most manufacturers specify a change every two years regardless of mileage. Never mix a glycol-based fluid with DOT 5 silicone fluid, and never reuse fluid that has been opened and left standing.Which fluid does my car takeThe required specification is printed on your brake fluid reservoir cap and in the owner's handbook. A fluid meeting a higher DOT number may be used where a lower one is specified, but never the reverse. If you are unsure, send us your registration number and we will help you confirm it.Buying thisGST-inclusive pricing with a proper invoice, shipped across India.

Read more less

The NGage HB 163 and HBS 163 rear brake pads are disc brake pads developed for the rear brake caliper used on Triumph’s 400-series motorcycles, including the Speed 400, Scrambler 400X, and T4. These pads are manufactured to match the exact pad shape, mounting dimensions, and contact profile required by the rear brake system fitted to these motorcycles, ensuring correct physical fitment and consistent disc engagement. This product listing applies strictly to the rear brake position. The front brake pads for these models use different pad codes and are listed separately. Rear brake pads play a critical stabilizing role in a motorcycle’s braking system. While the front brake provides the majority of stopping force, the rear brake contributes to balance, low-speed control, corner stability, and controlled deceleration. A rear brake pad must deliver predictable bite, smooth modulation, and stable friction behavior across varying temperatures and road conditions. NGage offers the HB 163 rear brake pad shape in two distinct friction material variants: Whisker Ceramic (HB 163) and Sintered (HBS 163). Both variants share identical physical dimensions and mounting geometry. The difference lies entirely in the friction compound formulation and its behavior under load and temperature. Whisker Ceramic Variant, HB 163 The HB 163 Whisker Ceramic brake pads use a ceramic-based friction compound reinforced with fiber-like whiskers. This compound is engineered to deliver controlled braking response, predictable modulation, and stable friction output during everyday riding conditions. The ceramic matrix provides smooth engagement at the brake lever and progressive braking force buildup, making it well-suited for urban commuting, highway touring, and mixed riding environments. The whisker reinforcement enhances structural stability within the friction layer, helping the pad maintain consistent surface behavior during repeated braking cycles. This compound is designed for riders who prioritize refined rear brake feel, controlled deceleration, and low-noise operation while maintaining reliable braking performance under normal thermal loads. Sintered Variant, HBS 163 The HBS 163 Sintered brake pads use a metallic friction compound formed by fusing metal powders under high temperature and pressure. This manufacturing process produces a dense, durable friction material with high thermal stability and consistent friction output under elevated braking loads. Sintered brake pads are engineered to tolerate higher operating temperatures and maintain braking performance during repeated hard braking, high-speed riding, and extended downhill descents. The metallic composition offers stronger initial bite and sustained friction consistency under conditions where brake heat buildup is significant. This compound is intended for riders who operate in aggressive riding conditions, carry heavier loads, or frequently ride in environments that generate higher rear brake temperatures. Fitment & Compatibility This listing applies to the rear brake position on the following motorcycles: Compatibility (Rear Brake Only)Triumph Speed 400Triumph Scrambler 400XTriumph T4 The HB 163 and HBS 163 pad shape is shared across these three models for the rear caliper. Front brake pads use different pad codes and must be purchased separately. Variant Explanation This product is available in two NGage material variants: HB 163, Whisker Ceramic Brake PadsCeramic-based friction compoundOptimized for smooth braking responsePredictable modulation and controlled rear brake feelStable friction behavior under normal thermal loadsSuitable for daily riding, touring, and mixed conditions HBS 163, Sintered Brake PadsMetallic sintered friction compoundHigher temperature toleranceStronger braking bite under loadConsistent friction during repeated brakingSuitable for aggressive riding and high-heat conditions Both variants are identical in shape, thickness profile, and mounting design. Only the friction compound differs. Specifications Brand: NGageProduct Type: Motorcycle Disc Brake PadsPosition: RearPad Codes: HB 163 (Whisker Ceramic), HBS 163 (Sintered)Material Options: Ceramic-based or Metallic SinteredCertification: ARAI TestedManufacturing Origin: JapanApplication Type: Rear brake caliperMounting: Direct replacement design Installation / Usage Notes • Designed as a direct replacement for the stock rear brake pads• No modification required for compatible models• Install only in the rear brake caliper• Ensure brake caliper pistons are properly retracted before installation• Clean the caliper bracket and pad guide surfaces prior to fitting• Bedding-in procedure is recommended after installation• Avoid aggressive braking for the first 100-150 km to allow proper pad transfer• Professional installation is advised for optimal braking performance Correct bedding-in is essential to achieve stable friction behavior and consistent braking feel. Improper bedding may result in uneven pad wear or reduced braking efficiency.

Read more less

Brembo L04210 is a fully synthetic DOT 4 brake fluid, low viscosity, supplied in a 1 litre bottle.Low viscosity fluid stays thinner at low temperature, which lets ABS and stability control systems move fluid quickly in cold conditions. Where a car specifies a low viscosity fluid, a standard one is not a substitute.The figures below are the minimums the DOT 4 standard itself requires, not measured values for this bottle.Specification Part number L04210 Standard DOT 4 Volume 1 litre Type Fully synthetic, glycol ether based Minimum dry boiling point for this standard 230 °C Minimum wet boiling point for this standard 155 °C Viscosity class Low viscosity Brake fluid is hygroscopic, meaning it absorbs moisture from the air over time, and that moisture lowers its boiling point long before the fluid looks dirty. Most manufacturers specify a change every two years regardless of mileage. Never mix a glycol-based fluid with DOT 5 silicone fluid, and never reuse fluid that has been opened and left standing.Which fluid does my car takeThe required specification is printed on your brake fluid reservoir cap and in the owner's handbook. A fluid meeting a higher DOT number may be used where a lower one is specified, but never the reverse. If you are unsure, send us your registration number and we will help you confirm it.Buying thisGST-inclusive pricing with a proper invoice, shipped across India.

Read more less

Performance Braking Upgrade for Himalayan 450 The 66BHP Race Pro Sintered Brake Pads are engineered for the Royal Enfield Himalayan 450, delivering stronger stopping power, sharper response, and consistent braking across demanding riding conditions. Built for riders who need more braking authority on varied terrain and long-distance rides, these pads provide reliable performance when intensity and load increase. Sintered Compound Performance Race Pro pads use a sintered compound designed for performance-focused braking: Aggressive initial bite for immediate stopping response Stronger braking feel compared to standard pads Designed for higher braking loads and varied riding conditions This setup ensures a more controlled and assertive braking experience. High Heat Resistance Engineered for sustained braking under load: Maintains performance at higher temperatures Handles repeated braking pressure without rapid degradation Suitable for long-distance and demanding riding Fade-Resistant Braking Built for consistent performance over extended use: Reduced brake fade during prolonged braking Stable stopping power across repeated braking cycles Reliable control during descents and extended rides Wet and All-Weather Confidence Adapted for unpredictable riding environments: Stable braking response in wet conditions Predictable performance across changing road surfaces Improved rider confidence in varied weather conditions Built for Demanding Riding Conditions Race Pro is tuned for riders who go beyond standard riding scenarios: Stronger braking authority across terrains Better control during aggressive or loaded riding Suitable for touring, highway, and mixed-condition riding

Read more less

Confidence-Focused Braking Upgrade for CB350RS The 66BHP Street Pro Semi Ceramic Brake Pads are designed for the Honda CB 350 RS, offering a balanced upgrade over standard replacement pads with improved braking feel, consistency, and control. Engineered for real-world riding conditions, these pads focus on delivering predictable braking performance across daily traffic, highway use, and varying weather conditions. Semi-Ceramic Compound Performance Built using a semi-ceramic compound, the Street Pro pads provide: Stronger initial bite compared to basic pads Smoother and more controlled braking response Balanced performance without aggressive characteristics This setup ensures improved braking confidence without compromising everyday usability. Consistent Braking Across Conditions The pads are developed to maintain dependable braking feel in both wet and dry riding environments: Stable braking response during rain and humid conditions Predictable lever feel across varying road surfaces Improved rider confidence during sudden braking Cleaner and Quieter Operation Designed with practical riding in mind, the Street Pro pads help reduce common braking drawbacks: Low dust formula to keep wheels cleaner Reduced noise during braking Smoother overall braking feel Built for Daily and Touring Use The Street Pro range is tuned for versatility, making it suitable for: City traffic and stop-go riding Highway touring and higher-speed braking Weekend riding with consistent control

Read more less

NGage HB 164 / HBS 164 Front Brake Pads for Royal Enfield 450 & 650 Models, Ceramic & Sintered Options (Front Only) The NGage HB 164 / HBS 164 Front Brake Pads are precision-engineered front brake replacement pads designed specifically for select Royal Enfield motorcycles that use the HB 164 pad profile in the front brake caliper. These pads are manufactured in Japan and are listed in NGage’s official compatibility chart for exact-fit installation. This listing applies strictly to front brake fitment only. It does not cover rear brake pads. Brake pad shape accuracy is critical. The HB 164 platform is used across multiple Royal Enfield 450 and 650 motorcycles, including the Classic 650, Shotgun 650 and Super Meteor 650, and installing the correct pad ensures proper caliper seating, even pad wear, and consistent braking response. Both variants offered here share identical mounting dimensions and backing plate design. The only difference lies in the friction material compound. Compatibility (Front Brake Only) As per NGage’s official application chart, this pad profile is compatible with: Royal Enfield Classic 650 Royal Enfield Himalayan 450 Royal Enfield Guerrilla 450 Royal Enfield Interceptor 650 Royal Enfield Continental GT 650 Royal Enfield Super Meteor 650 Royal Enfield Shotgun 650 These models use the HB 164 front pad specification. Buyers should confirm fitment before installation, especially when upgrading between ceramic and sintered variants. Variant Explanation, HB vs HBS This product is available in two NGage friction material options: HB 164, Whisker Ceramic Brake Pads The HB 164 uses NGage’s Whisker Ceramic compound. This is a ceramic-based friction formulation designed for smooth bite progression and reduced brake noise. It is suitable for: Daily commuting Highway touring Urban riding Riders who prefer controlled lever feedback Ceramic pads are typically chosen for quieter braking and progressive modulation under standard operating temperatures. HBS 164, Sintered Brake Pads The HBS 164 uses a sintered metallic friction compound. This version is engineered for higher thermal resistance and sustained braking under load. It is suitable for: Aggressive riding Mountain descents Heavier motorcycles with luggage Riders seeking firmer braking response Sintered compounds generally maintain braking consistency across wider temperature variations. Both versions are ARAI tested and manufactured in Japan. Only the friction compound differs. Shape, dimensions, and installation procedure remain the same. Performance Characteristics Brake pads influence more than stopping distance. They affect lever feel, fade resistance, disc wear patterns, and braking stability under repeated deceleration. The NGage HB 164 / HBS 164 Front Brake Pads are engineered to deliver: Stable braking response Consistent contact with the brake disc Predictable lever modulation Uniform wear across the friction surface Performance can vary depending on riding style, road conditions, brake disc condition, and bedding-in procedure. Material & Construction Overview Both variants use a precision-formed backing plate engineered to match the Royal Enfield front caliper design. Proper plate rigidity ensures even pressure distribution across the friction surface. The friction compound is bonded using controlled manufacturing processes designed to withstand heat cycles generated during braking. NGage does not publish internal compound percentages or heat range values beyond the ceramic and sintered classification. The product is listed as ARAI tested, indicating it has undergone evaluation under Indian regulatory standards. Installation & Bedding-In Installation should be performed only on the front brake caliper of the compatible models listed above. After installation, a proper bedding-in procedure is strongly recommended. Bedding-in allows the friction material to transfer evenly onto the brake disc surface, helping establish consistent braking behaviour. Failure to bed in new pads correctly may lead to uneven wear or inconsistent lever feel. Professional installation is advised for riders unfamiliar with brake servicing procedures. What’s Included 1 × Set of NGage Front Brake Pads(HB 164, Whisker Ceramic or HBS 164, Sintered, depending on selected variant) No additional mounting pins, shims, springs, or hardware are included unless shown in product images. Specifications Brand: NGageProduct Type: Motorcycle Disc Brake PadsPosition: FrontPad Codes: HB 164 (Whisker Ceramic) / HBS 164 (Sintered)Compatibility: Royal Enfield 450 & 650 models listed aboveCertification: ARAI TestedCountry of Manufacture: JapanFitment Type: Direct replacement

Read more less

CRANK1 performance brake pads for the Honda CB300R, all in one place. Choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Honda CB300R: Front (2018-2021) Rear (2024) Rear (2018-2021) Front + Rear (2024) Front + Rear (2018-2021) Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Honda CB300R?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

Performance Braking Upgrade for Classic 650 The 66BHP Race Pro Sintered Brake Pads are designed for the Royal Enfield Classic 650, delivering stronger stopping power, sharper response, and consistent braking under demanding riding conditions. Built for riders who need improved braking confidence on a heavier motorcycle platform, these pads provide better control when speed and load increase. Sintered Compound Performance Race Pro pads use a sintered compound engineered for performance braking: Aggressive initial bite for stronger stopping response Improved braking feel compared to standard pads Designed for higher braking loads This setup delivers a more assertive and controlled braking experience. High Heat Resistance Developed to manage sustained braking pressure: Maintains braking performance under high temperatures Handles repeated braking without rapid performance loss Suitable for highway and long-distance riding Fade-Resistant Braking Built for consistent performance over extended use: Reduced brake fade during prolonged braking Stable stopping power across repeated braking cycles Reliable control during long rides and descents Wet and All-Weather Confidence Adapted for real-world riding environments: Stable braking response in wet conditions Predictable braking feel across varying road surfaces Improved rider confidence in unpredictable conditions Built for Touring and Performance Riding Race Pro is tuned for riders who demand stronger braking authority: Better control for heavier motorcycles Improved confidence during high-speed riding Suitable for highway, touring, and spirited riding

Read more less

The NGage HB 184 and HBS 184 front brake pads are disc brake pads developed for the front brake caliper used on the Triumph Speed 400 and Triumph Scrambler 400X. These brake pads are manufactured to match the exact pad shape, mounting profile, and contact surface geometry required by the front braking system fitted to these motorcycles, ensuring correct physical fitment and consistent disc engagement. This product listing applies strictly to the front brake position. The rear brake pads for these models use a different pad code and are listed separately. Front brake pads play the primary role in a motorcycle’s braking system. The majority of stopping force is generated at the front wheel, which makes front brake pad selection critical for braking confidence, lever feel, and controlled deceleration. A front brake pad must deliver stable friction behavior, predictable bite, and consistent performance across a wide range of temperatures and braking loads. NGage offers the HB 184 front brake pad shape in two friction material variants: Whisker Ceramic (HB 184) and Sintered (HBS 184). Both variants share identical physical dimensions and mounting geometry. The difference lies entirely in the friction compound formulation and how it behaves under heat, load, and repeated braking cycles. Whisker Ceramic Variant, HB 184 The HB 184 Whisker Ceramic brake pads use a ceramic-based friction compound reinforced with fiber-like whiskers. This compound is engineered to deliver smooth initial bite, progressive braking force buildup, and stable friction output during everyday riding conditions. The ceramic matrix allows controlled modulation at the brake lever, which is particularly useful in urban riding, highway cruising, and mixed riding environments where precise braking control is preferred. The whisker reinforcement improves structural stability within the friction layer, helping the pad maintain consistent surface behavior under repeated braking cycles. This compound is designed for riders who prioritize refined braking feel, predictable front brake response, and consistent deceleration without aggressive bite characteristics. Sintered Variant, HBS 184 The HBS 184 Sintered brake pads use a metallic friction compound formed by fusing metal powders under high temperature and pressure. This manufacturing process produces a dense, wear-resistant friction material with high thermal stability and consistent friction output under elevated braking loads. Sintered brake pads are engineered to tolerate higher operating temperatures and maintain braking performance during repeated hard braking, extended downhill descents, and high-speed riding. The metallic composition offers stronger initial bite and sustained friction consistency under conditions where brake heat buildup is significant. This compound is intended for riders who operate in aggressive riding conditions, carry heavier loads, or frequently ride in environments that generate higher front brake temperatures. Fitment & Compatibility This listing applies to the front brake position on the following motorcycles: Compatibility (Front Brake Only)Triumph Speed 400Triumph Scrambler 400X The HB 184 and HBS 184 pad shape is shared across these two models for the front caliper. Rear brake pads use a different pad code and must be purchased separately. Variant Explanation This product is available in two NGage material variants: HB 184, Whisker Ceramic Brake PadsCeramic-based friction compoundOptimized for smooth braking responseProgressive front brake feelStable friction behavior under normal thermal loadsSuitable for daily riding, touring, and mixed conditions HBS 184, Sintered Brake PadsMetallic sintered friction compoundHigher temperature toleranceStronger braking bite under loadConsistent friction during repeated brakingSuitable for aggressive riding and high-heat conditions Both variants are identical in shape, thickness profile, and mounting design. Only the friction compound differs. Specifications Brand: NGageProduct Type: Motorcycle Disc Brake PadsPosition: FrontPad Codes: HB 184 (Whisker Ceramic), HBS 184 (Sintered)Material Options: Ceramic-based or Metallic SinteredCertification: ARAI TestedManufacturing Origin: JapanApplication Type: Front brake caliperMounting: Direct replacement design Installation / Usage Notes • Designed as a direct replacement for the stock front brake pads• No modification required for compatible models• Install only in the front brake caliper• Ensure brake caliper pistons are properly retracted before installation• Clean the caliper bracket and pad guide surfaces prior to fitting• Bedding-in procedure is recommended after installation• Avoid aggressive braking for the first 150-200 km to allow proper pad transfer• Professional installation is advised for optimal braking performance Correct bedding-in is essential to achieve stable friction behavior and consistent braking feel. Improper bedding may result in uneven pad wear or reduced braking efficiency.

Read more less

The NGage HB 150 and HBS 150 rear brake pads are designed for Honda’s CB 350 platform, covering the CB 350, CB 350C, CB 350 H’ness, and CB 350RS. These pads are shaped to match the rear brake caliper profile used on these motorcycles, ensuring correct fitment and proper contact with the brake disc. This listing is for the rear brake position only. Front brake pads for these models are listed separately under a different pad code. NGage offers this pad shape in two friction material options, Whisker Ceramic and Sintered, allowing riders to select the compound that best suits their braking preference, riding style, and operating conditions. Friction Material Options (Variants) HB 150, Whisker Ceramic Brake PadsThis variant uses NGage’s whisker-reinforced ceramic compound, engineered for smooth braking response and controlled modulation. The ceramic matrix is tuned for stable everyday performance, making it suitable for urban riding, highway use, and touring where predictable rear brake feel is preferred. HBS 150, Sintered Brake PadsThis variant uses a metallic sintered friction compound formed under high temperature and pressure. It is built for higher thermal stability and stronger bite under demanding braking conditions. The sintered formulation is suited for riders who load the rear brake more aggressively or ride in conditions that generate higher brake temperatures. Both variants share the same physical dimensions and mounting geometry. Only the friction compound differs. Compatibility, Rear Brake Only Honda CB 350Honda CB 350CHonda CB 350 H’nessHonda CB 350RS This listing applies strictly to the rear brake caliper of the above models. Technical Overview Brand: NGageProduct Type: Motorcycle Disc Brake PadsPosition: RearPad Codes: HB 150 (Whisker Ceramic), HBS 150 (Sintered)Material Options: Ceramic-based or Sintered metallicCertification: ARAI Tested (as indicated by NGage)Manufacturing Origin: Japan (as indicated by NGage) Installation & Use Notes • Designed for direct replacement in the stock rear caliper• No modification required when installed on compatible models• Follow standard brake pad bedding-in procedures after installation• Professional installation recommended for consistent braking performance• Always replace brake pads as a complete axle set where applicable

Read more less

The NGage HB 089 and HBS 089 front brake pads are engineered for Honda’s CB 350 platform, covering the CB 350 H’ness, CB 350RS, and CB 350. These pads are designed to match the front brake caliper dimensions and mounting profile required for these motorcycles, ensuring direct fitment without modification. This listing is for the front brake position only. Rear brake pads are listed separately under a different product code. NGage offers this pad shape in two distinct friction materials, Whisker Ceramic and Sintered, allowing riders to select the compound that best aligns with their riding style, usage pattern, and braking preference. Friction Material Options (Variants) HB 089, Whisker Ceramic Brake PadsThis variant uses NGage’s whisker-reinforced ceramic compound, designed to deliver progressive braking feel, consistent modulation, and stable performance under everyday riding conditions. The ceramic matrix is optimized for controlled heat behavior and smooth engagement, making it well-suited for city riding, touring, and highway use. HBS 089, Sintered Brake PadsThis variant uses a metallic sintered friction compound formed under high temperature and pressure. It is engineered for higher thermal stability and strong bite under demanding braking conditions. The sintered formulation is suitable for aggressive riding, high-load usage, and situations where consistent braking performance is required at elevated temperatures. Both variants share the same physical shape, thickness, and mounting profile. Only the friction compound differs. Compatibility, Front Brake Only Honda CB 350 H’nessHonda CB 350RSHonda CB 350 This listing applies strictly to the front brake caliper of the above models. Technical Overview Brand: NGageProduct Type: Motorcycle Disc Brake PadsPosition: FrontPad Codes: HB 089 (Whisker Ceramic), HBS 089 (Sintered)Material Options: Ceramic-based or Sintered metallicCertification: ARAI Tested Manufacturing Origin: Japan  Installation & Use Notes • Designed for direct replacement in the stock front caliper• No modification required when installed on compatible models• Follow standard brake pad bedding-in procedures after installation• Professional installation recommended for optimal braking performance• Always replace brake pads as a complete axle set

Read more less

NGage HB 155 / HBS 155 Rear Brake Pads for Royal Enfield Classic 650, Super Meteor 650 & Shotgun 650, Ceramic & Sintered Options (Rear Only) The NGage HB 155 and HBS 155 rear brake pads are disc brake pads designed for Royal Enfield motorcycles that use this exact pad shape and mounting specification at the rear brake caliper. These brake pads are specified for the Royal Enfield Classic 650Royal Enfield Super Meteor 650 and Royal Enfield Shotgun 650 in the rear brake position. These motorcycles share the same rear brake pad format, allowing a single pad code to be used across the range. This listing covers the rear brake pad set only for these motorcycles. Brake Pad Function & Fitment Logic Brake pads are a core wear component in a motorcycle’s braking system. Their role is to generate friction against the brake disc when hydraulic pressure is applied through the brake caliper. For proper braking behavior, brake pads must match the exact backing plate shape, thickness, and mounting profile specified for the brake caliper design used on the motorcycle. NGage brake pad codes define this physical geometry. Only pads with the correct code should be installed in a given caliper. For the motorcycles covered under this listing: HB 155 represents the Whisker Ceramic variant HBS 155 represents the Sintered variant Both variants share identical dimensions and mounting features. The only difference between the two is the friction material composition. Using the correct pad code is essential. Installing pads with a different shape or specification can lead to improper seating, uneven pad wear, brake noise, inconsistent braking response, or long-term damage to braking components. Variant Explanation This product is available in two NGage material variants: HB 155, Whisker Ceramic Brake PadsThis variant uses a ceramic-based friction compound reinforced with whisker fibers. It is classified by NGage as a Whisker Ceramic brake pad. The compound is designed to provide stable braking behavior and consistent friction characteristics under standard road riding conditions. HBS 155, Sintered Brake PadsThis variant uses a metallic sintered friction compound. It is classified by NGage as a Sintered brake pad. Sintered pads are manufactured using fused metallic powders and are typically selected where higher thermal stability and consistent braking behavior under sustained load are required. Both variants are identical in shape, fitment, and mounting dimensions.Only the friction material composition differs between HB and HBS variants. Intended Application The NGage HB 155 and HBS 155 rear brake pads are direct-replacement components for the rear brake calipers used on the Royal Enfield Classic 650, Royal Enfield Super Meteor 650 and Royal Enfield Shotgun 650. These brake pads are not universal and are not interchangeable with other NGage pad codes such as HB 163, HB 164, or HB 184. They are intended strictly for motorcycles that specify pad code HB 155 or HBS 155 at the rear. Installation & Service Considerations Brake pads are routine service components and should be replaced according to the motorcycle manufacturer’s recommended service intervals or when pad thickness reaches the wear limit. Installation should follow standard brake service procedures, including: Cleaning the brake caliper and pad guide surfaces Inspecting the brake disc for wear or scoring Seating the pads correctly within the caliper Tightening mounting hardware to the correct torque Performing a bed-in procedure after installation Improper installation can result in brake noise, uneven wear, or inconsistent braking response. Professional installation is recommended for riders who are not familiar with motorcycle brake system service procedures. Summary The NGage HB 155 and HBS 155 rear brake pads are direct-replacement brake pads designed for Royal Enfield 650cc motorcycles that use this exact rear pad format. Available in Whisker Ceramic and Sintered variants, these pads provide two friction material options while maintaining identical fitment geometry. Correct specification matching and proper installation are essential prior to use. Compatibility (Rear Only) Royal Enfield Classic 650 Royal Enfield Super Meteor 650 Royal Enfield Shotgun 650 Variant Explanation Whisker Ceramic (HB 155): Ceramic-based friction compound Sintered (HBS 155): Metallic sintered friction compound Both variants share identical fitment and mounting dimensions Specifications Brand: NGage Product Type: Motorcycle brake pads Position: Rear Pad Codes: HB 155 (Whisker Ceramic), HBS 155 (Sintered) Compatibility: Royal Enfield Classic 650, Royal Enfield Super Meteor 650, Royal Enfield Shotgun 650 Certification Marking: ARAI Tested Manufacturing Origin: Japan Installation / Usage Notes Install only in the rear brake caliper position Use only the specified pad code for your motorcycle Perform bed-in procedure after installation Professional installation recommended

Read more less

Brembo Sport 07.D435.12 is a brake pad set for the Mercedes M CLASS w166 (2012 - )/GL X166 and GLS/GLE, using the Brembo Sport compound, a higher-friction pad built to resist fade under sustained hard braking.Brembo Sport characteristics Intended use Sport driving, paired with Brembo Max or Xtra discs Character Superior performance and fade resistance Technical content Exceeds OE Identification Black backplate, red shim Approval Brembo certified quality, ECE R90 Fitment guidanceListed against the Mercedes M CLASS w166 (2012 - )/GL X166 and GLS/GLE. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.Compound characteristics as published by Brembo Sport.Is this the right pad for your car?Brembo Sport is built around heat. It holds its bite through repeated hard stops where a standard pad would begin to fade. That resistance comes from a compound formulated to work warm. Choose Sport Spirited driving, track days, hill runs and towing. You want fade resistance above everything else. Choose Prime City and highway driving. You want strong bite from cold, quiet running and low dust. Worth knowing before you order. Cold, in ordinary traffic, a Sport pad bites less than an OE-specification pad until it has warmed through, and it runs a little noisier. That is the trade for fade resistance, not a fault. If most of your driving is on the road, the Prime pad is the better brake.The road pad for this car is Brembo Prime P37017, ₹7,226.

Read more less

Brembo P83082 is a front-axle brake pad set from Brembo's Prime range for the Toyota COROLLA NEW ALTIS PETROL ONLY, measuring 139 mm wide, 56 mm tall and 18 mm thick.Prime is Brembo's OE-matched road range. The friction material is specified to match original equipment braking performance, the backplate is painted against corrosion, an anti-squeal shim is included, and the set is ECE R90 type-approved. Brembo lists it as the pad to run with Prime brake discs.This is not the Xtra range, which is Brembo's sport pad line for drilled discs, and not the ceramic (N-suffix) range, which we do not currently stock.Specification Range Brembo Prime Technical content OE-matched Axle Front Width 139 mm Height 56 mm Thickness 18 mm Braking system Akebono WVA number 24336 FMSI D1210 8330 Backplate Black, painted Accessories Anti-squeal shim Wear indicator Not built into the pad Approval ECE R90 type-approved EAN code 8020584062203 This set does not have a wear indicator built into the pad. If your Toyota COROLLA NEW ALTIS PETROL ONLY uses an electronic brake wear sensor, that sensor is a separate part and is normally replaced at the same time as the pads.Fitment guidanceListed against the Toyota COROLLA NEW ALTIS PETROL ONLY. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

Brembo P79008 is a front-axle brake pad set from Brembo's Prime range for the Maruti/Suzuki JIMNY NEW, measuring 117 mm wide, 46 mm tall and 15 mm thick.Prime is Brembo's OE-matched road range. The friction material is specified to match original equipment braking performance, the backplate is painted against corrosion, an anti-squeal shim is included, and the set is ECE R90 type-approved. Brembo lists it as the pad to run with Prime brake discs.This is not the Xtra range, which is Brembo's sport pad line for drilled discs, and not the ceramic (N-suffix) range, which we do not currently stock.Specification Range Brembo Prime Technical content OE-matched Axle Front Width 117 mm Height 46 mm Thickness 15 mm Braking system Akebono WVA number 21907,21909,21908 FMSI D556 7435, D807 7680 Backplate Black, painted Accessories Anti-squeal shim Wear indicator Acoustic, built into the pad Approval ECE R90 type-approved EAN code 8020584057285 These pads carry an acoustic wear indicator, a metal tab that contacts the disc and squeals once the friction material nears its limit. Treat that noise as a prompt to inspect the pads.Fitment guidanceListed against the Maruti/Suzuki JIMNY NEW. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the front axle. One set covers both wheels on the axle.Specifications published by Brembo.

Read more less

CRANK1 performance brake pads for the TVS Apache RTR 160 4V, all in one place. Choose your compound (Ceramic) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the TVS Apache RTR 160 4V:RearFront fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my TVS Apache RTR 160 4V?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Yezdi Roadster, all in one place. Choose your compound (Ceramic) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Yezdi Roadster: Front Rear Front + Rear Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Yezdi Roadster?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Triumph Speed T4, all in one place. Choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Triumph Speed T4: Front Rear Front + Rear Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Triumph Speed T4?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

High-Performance Braking Upgrade for Speed 400 & Scrambler 400 X The 66BHP Race Pro Sintered Brake Pads are engineered for riders who demand stronger stopping power, sharper bite, and consistent braking under high load conditions. Built for performance-focused riding, these pads deliver increased braking authority when speed, road conditions, and riding intensity rise. Sintered Compound Performance The Race Pro pads use a sintered compound designed for higher braking demands: Aggressive initial bite for stronger stopping response Designed for performance-oriented riding conditions Maintains braking consistency under load This setup is tuned for riders who want more than standard braking feel. High Heat Resistance Developed to handle repeated braking pressure: Resists heat buildup during aggressive riding Maintains braking performance under sustained use Suitable for high-speed and highway conditions Fade-Resistant Braking Built to deliver dependable braking even under stress: Reduced performance drop during prolonged braking Consistent braking feel on descents and repeated stops Maintains control in demanding scenarios Wet and All-Weather Confidence Designed for variable riding environments: Stable braking response in wet conditions Reliable performance across changing road surfaces Improved rider confidence in unpredictable conditions Built for Performance Riding Race Pro is tuned for riders pushing beyond everyday limits: Stronger braking authority at higher speeds More control during aggressive riding Suitable for highway, touring, and spirited riding

Read more less

BrakeKraft BK2114230712 is a rear-axle brake disc for the Mercedes E CLASS W212 (2010-2016) E250CDI, from the BrakeKraft Drilled & Slotted range, a cross-drilled and slotted performance disc.BrakeKraft Drilled & Slotted characteristics Surface Cross-drilled and slotted Intended use Performance road driving Purpose of drilling Vents gas and heat away from the pad face Purpose of slotting Clears dust and debris, keeps the pad surface biting cleanly Fitment guidanceListed against the Mercedes E CLASS W212 (2010-2016) E250CDI. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.This listing covers the rear axle. Discs are sold individually and replaced as a pair, so you need two for the axle.Compound characteristics as published by BrakeKraft.

Read more less

The 66bhp Venta is an ultra premium 320mm floating front rotor for the Royal Enfield Interceptor 650 and Continental GT 650, for riders who want a measurable gain in braking feel without a workshop visit. It installs in place of the original disc with no cutting, drilling or alteration.The 650 twins carry real weight, and the standard front disc is the component that shows it first on a long descent or a hard road ride. The Venta pairs a lightweight aluminium inner carrier with a high carbon stainless steel outer ring, joined by floating bobbins. That floating construction lets the braking surface move laterally against the carrier by a small controlled amount, which is what gives the lever its more progressive, better resolved feel. The petal profile and large ventilation cuts move heat out during repeated braking, so the bite point stays where you left it.Key features 320mm diameter, 5.0mm high carbon stainless steel outer ring Aluminium inner carrier, reducing rotating mass against a solid disc Floating bobbin system for progressive lever feel High ventilation petal profile for heat management under repeated braking Direct replacement for the original disc, no modification required Available with a black or red carrier FitmentListed for the Royal Enfield Interceptor 650 and Continental GT 650. Get in touch if you would like help confirming it against your bike.

Read more less

DBA DB1818SS is a brake pad set for the Maruti/suzuki SWIFT all models/Ritz/Astar/NewBaleno/Dezire, using the DBA Street Series (SS) compound, a comfort-focused street pad with low noise and low dust.DBA Street Series (SS) characteristics Intended use General light-duty street driving Priority Comfort: low noise, low dust Bedding in Bedding-in stripe gives higher initial friction while the pad beds Fitment guidanceListed against the Maruti/suzuki SWIFT all models/Ritz/Astar/NewBaleno/Dezire. Brake parts vary by variant, engine, build year and the braking system fitted, so send us your registration number and we will help you confirm the right part before you order.Buying this partGST-inclusive pricing with a proper invoice, shipped across India.Compound characteristics as published by DBA.

Read more less