Benelli Motorcycle Accessories

Control Your Exhaust. On Your Terms. Your valved exhaust has two modes, you just haven't been able to use both. The Valvetronic Exhaust Valve Control Module (Manual) gives you a handlebar-mounted switch that physically opens or closes the exhaust butterfly valve whenever you want. Full roar on the open highway. Clean and quiet through the colony, toll booth, or early morning streets. No apps. No wiring. No compromise. This is the most reliable way to control a valved exhaust, because there's nothing electronic to fail. A cable connects your thumb to the valve. That's it. What This Module Does Valved exhausts come with an internal butterfly valve that changes how exhaust gases flow. When the valve is closedgases pass through a baffled internal route, quieter, more refined. When the valve is opengases take the free-flow path, louder, rawer, with a more aggressive exhaust note. Most valved exhausts ship without any control module. The valve stays fixed in one position. This module gives you a switch to change it, whenever you want, from the handlebar. Closed valve: Quiet, compliant, neighbour-friendly. Use it in residential areas, at idle, in traffic, on early morning rides. Open valve: The sound your exhaust was built to make. Use it on highways, open roads, or anywhere you want the full character of your exhaust to come through. Why Manual Over Electric Zero electronics. No solenoid, no servo, no wiring loom, no relay. Nothing to short, corrode, or fail over time. Works anywhere, always. The valve opens when you pull the cable. No power required. No sensor needed. Doesn't care if your bike is warm, cold, or idling. You're in control. The valve is exactly where you put it, open or closed, until you choose to change it. No automatic switching when you don't want it. Simple to install. Route the cable, connect to the valve actuator, mount the switch. No ECU tapping, no wiring diagrams, no calibration. Built to last. A cable and a switch outlast any electronic actuator on a motorcycle. Less to maintain, less to replace. How It Works A control switch mounts on your handlebar. A cable runs from the switch down to the butterfly valve actuator on your exhaust. When you flick the switch, cable tension physically rotates the valve between open and closed. The entire system is mechanical, no power draw from your bike's electrical system, no ECU communication, no mapping required. Installation requires routing the cable cleanly along the frame to the exhaust, connecting to the existing valve actuator arm, and adjusting cable tension for full travel in both directions. A standard workshop should be able to install this in under an hour on most platforms. Compatible Bikes This is a universal moduleit works with any valved exhaust system that supports mechanical cable actuation, regardless of bike brand or model. Below is a verified compatibility reference across popular Indian market platforms. If your bike has a valved slip-on, this module can control it. Royal Enfield Interceptor 650 / Continental GT 650 / Classic 650 / Bear 650 Classic 350 (Reborn) / Hunter 350 / Meteor 350 Himalayan 411 / Himalayan 450 / Guerrilla 450 Scram 411 / Super Meteor 650 / Shotgun 650 KTM Duke 125 / Duke 200 / Duke 250 / Duke 390 RC 125 / RC 200 / RC 390 Adventure 250 / Adventure 390 / Adventure 390 (2025) 790 Adventure Triumph Speed 400 / Scrambler 400 X / Tiger 400 Street Triple 675 / Speed T4 Bonneville T100 / T120 / Street Twin Tiger 800 / Street Scrambler 900 Yamaha MT-15 V2 / R15 V3 / R15 V4 FZ25 / FZS25 / Fazer 25 MT-03 / R3 YZF-R1 / YZF-R6 / MT-07 Kawasaki Ninja 400 / Ninja 650 / Ninja 1000 SX Z800 / Z900 / Z900 (2026) Versys 650 / Versys-X 300 / Versys 1000 Honda CB200X / CB350 Highness / CB350RS CBR 250R / CB300R / CB300F CBR 650R / CBR 650F / CB Hornet 160R Africa Twin / NX200 Bajaj Pulsar NS200 / RS200 / AS200 / 220F Dominar 250 / Dominar 400 NS 400Z TVS Apache RR 310 / Apache RTR 200 4V Ronin BMW G 310 R / G 310 GS / G 310 RR S 1000 R / S 1000 XR / R 1000 GS Suzuki Gixxer 250 / V-Strom 250SX / V-Strom 650 GSX-R750 / GSX-S750 / GSX-R1000 Hayabusa (2021 Onwards) Ducati Scrambler 800 / Scrambler 1100 Monster 797 / Monster 1200 Hypermotard 939 / Multistrada 950 Streetfighter V4 Harley Davidson Street 750 / Street Rod X440 / X440T Forty Eight / Iron 883 Jawa / Yezdi Jawa 42 FJ / Jawa Perak Yezdi Adventure / Yezdi Roadster Hero Karizma XMR / Xpulse 200 4V / Xpulse 210 Benelli TRK 502 / TRK 502X / TNT 600i / TNT 899 This module is universal, it controls the valve mechanism, not the exhaust itself. Your exhaust must have a butterfly valve with a mechanical actuator arm. Confirm exhaust compatibility before ordering. If your bike model isn't listed but runs a valved slip-on, this module will work. What's in the Box 1 × Valvetronic Manual Control Switch (handlebar mount) 1 × Control cable assembly Mounting hardware Exhaust system not included. Module requires a compatible valved exhaust to function. Specifications Control Type: Manual (mechanical cable) Actuation: Direct cable-pull butterfly valve operation Power Required: None ECU / Wiring Integration: Not required Valve Positions: Open / Closed (user-operated) Mount: Handlebar switch with cable routing Fitment: Universal, compatible with mechanically-actuated valved exhausts Brand: Valvetronic MRP: ₹3,499 Also Available Want automatic valve switching based on RPM and throttle input? The Valvetronic Electric (Automatic) Module does exactly that, the valve opens and closes on its own as you ride. View the Electric Module →

Read more less

NGK Iridium IX. A 0.6mm fine-wire iridium centre electrode in place of a conventional one, firing a sharper, more focused spark. On a higher-revving sports engine that means crisper throttle response, easier cold starts and more consistent ignition, held steady by an electrode that barely erodes. Direct fit. Nothing to adjust. Find your bike Yamaha · YZF-R15 · YZF-R15 2.0 · YZF-R3  R3 is a twin, takes 2 Kawasaki · Ninja 250 · Ninja 250R · Ninja 300 · Z250 · KX 250F Honda · CBR 150R · CBR 125R Benelli · TNT 25 · TNT 300 · Leoncino 500 · Leoncino 500 Trail · TRK 502 · TRK 502X LML · Beamer · Freedom · Graptor R15 V3, V4 and the MT-15 take the MR8E-9, a standard plug. NGK does not make an iridium version for those bikes. If you want an upgrade for a V4 or MT-15, the Ngage B8RII-8 is the one to look at. Specifications Part number · CR8EIX Type · Iridium IX, 0.6mm fine wire Heat range · 8 Conventional equivalent · CR8E Sold as · single plug Fitting Arrives pre-gapped and ready to fit. Thread in by hand first, then torque to your manual's figure. If you check the gap, move the outer electrode only. Unsure which you need? Send us your bike and year and we will confirm before you order.

Read more less

Your Exhaust. Intelligent. Automatic. The Valvetronic Electric (Automatic) Exhaust Valve Control Module brings smart valve control to your valved exhaust. The butterfly valve opens and closes automatically, no switches to flip, no cables to pull. It reads riding input and actuates the valve on its own, giving you the quiet mode when you need it and the full exhaust character when you're pushing hard. This is the premium way to run a valved exhaust. Set it and forget it. The system handles the rest. What This Module Does Valved exhausts have an internal butterfly valve that controls exhaust gas routing. Valve closed = exhaust gases take a baffled internal path, quieter, more refined note. Valve open = free-flow path, the full aggressive exhaust character your slip-on was built for. The Electric Module automates this. A solenoid or servo actuator connects to the butterfly valve. The control unit reads signals from your bike, RPM, throttle position, or a dedicated switch, and commands the valve to open or close accordingly. You get intelligent mode switching without any manual input mid-ride. Low RPM / idle / city: Valve stays closed. Quiet, controlled, compliant. Use it on early morning starts, residential areas, toll plazas, traffic jams. Higher RPM / open throttle / highway: Valve opens automatically. The exhaust opens up, the note deepens, and you get the full sound profile of your slip-on exhaust. Why Electric Over Manual Fully automatic operation. The valve transitions without any rider input. Focus on riding, the module handles valve control in the background. Seamless transitions. No fumbling with a switch mid-corner or on a highway run. The valve opens and closes at the right moment, every time. Consistent behaviour. Same switching point every ride. No forgetting to open the valve before a run or close it before entering the city. Optional override. Most configurations allow a dedicated switch for manual override if you want direct control in specific situations. Premium install. Cleaner setup than a cable system, no handlebar clutter, no cable routing along the frame. How It Works The control unit connects to your bike's wiring, typically tapping into the ignition circuit, RPM signal, or a dedicated output. When the defined threshold is crossed (RPM, throttle position, or switch activation), the unit sends a signal to an electric actuator mounted on the exhaust valve. The actuator rotates the butterfly valve between open and closed positions in milliseconds. The system draws minimal current from the battery and does not require ECU remapping, fuel map changes, or custom tuning. Installation involves wiring the control unit to the correct signal source and mounting the actuator to the exhaust valve arm. A professional auto electrician or experienced mechanic can complete the installation cleanly on most bikes in 1-2 hours. Compatible Bikes This is a universal moduleit works with any valved exhaust system that supports electric or solenoid actuation, regardless of bike brand or model. Below is a verified compatibility reference across popular Indian market platforms. If your bike has a valved slip-on, this module can control it. Royal Enfield Interceptor 650 / Continental GT 650 / Classic 650 / Bear 650 Classic 350 (Reborn) / Hunter 350 / Meteor 350 Himalayan 411 / Himalayan 450 / Guerrilla 450 Scram 411 / Super Meteor 650 / Shotgun 650 KTM Duke 125 / Duke 200 / Duke 250 / Duke 390 RC 125 / RC 200 / RC 390 Adventure 250 / Adventure 390 / Adventure 390 (2025) 790 Adventure Triumph Speed 400 / Scrambler 400 X / Tiger 400 Street Triple 675 / Speed T4 Bonneville T100 / T120 / Street Twin Tiger 800 / Street Scrambler 900 Yamaha MT-15 V2 / R15 V3 / R15 V4 FZ25 / FZS25 / Fazer 25 MT-03 / R3 YZF-R1 / YZF-R6 / MT-07 Kawasaki Ninja 400 / Ninja 650 / Ninja 1000 SX Z800 / Z900 / Z900 (2026) Versys 650 / Versys-X 300 / Versys 1000 Honda CB200X / CB350 Highness / CB350RS CBR 250R / CB300R / CB300F CBR 650R / CBR 650F / CB Hornet 160R Africa Twin / NX200 Bajaj Pulsar NS200 / RS200 / AS200 / 220F Dominar 250 / Dominar 400 NS 400Z TVS Apache RR 310 / Apache RTR 200 4V Ronin BMW G 310 R / G 310 GS / G 310 RR S 1000 R / S 1000 XR / R 1000 GS Suzuki Gixxer 250 / V-Strom 250SX / V-Strom 650 GSX-R750 / GSX-S750 / GSX-R1000 Hayabusa (2021 Onwards) Ducati Scrambler 800 / Scrambler 1100 Monster 797 / Monster 1200 Hypermotard 939 / Multistrada 950 Streetfighter V4 Harley Davidson Street 750 / Street Rod X440 / X440T Forty Eight / Iron 883 Jawa / Yezdi Jawa 42 FJ / Jawa Perak Yezdi Adventure / Yezdi Roadster Hero Karizma XMR / Xpulse 200 4V / Xpulse 210 Benelli TRK 502 / TRK 502X / TNT 600i / TNT 899 This module is universal, it controls the valve mechanism, not the exhaust itself. Your exhaust must have a butterfly valve with an actuator arm compatible with electric operation. Confirm exhaust compatibility before ordering. If your bike model isn't listed but runs a valved slip-on, this module will work. What's in the Box 1 × Valvetronic Electric Control Unit 1 × Electric actuator assembly Wiring harness and connectors Mounting hardware Exhaust system not included. Module requires a compatible valved exhaust to function. Specifications Control Type: Automatic (electric / solenoid-actuated) Actuation: Electric servo / solenoid butterfly valve operation Power Required: 12V DC (motorcycle battery) ECU Integration: Signal tap, no remapping required Valve Positions: Open / Closed (auto-switching) Override: Manual switch override supported Mount: Control unit + actuator on exhaust valve arm Fitment: Universal, compatible with electrically-actuated valved exhausts Brand: Valvetronic MRP: ₹6,499 Manual vs Electric, Which One to Choose Feature Manual (₹3,499) Electric / Auto (₹6,499) Valve Control Rider-operated switch Automatic (RPM/throttle-based) Power Required None 12V (bike battery) Wiring Not required Signal tap required Install Complexity Simple Moderate Failure Points Minimal (cable only) Electronic components Best For Riders who want full manual control Riders who want a set-and-forget system Also Available Prefer a simpler, zero-electronics setup? The Valvetronic Manual Module gives you direct cable-pull control from your handlebar, no wiring, no power required. View the Manual Module →

Read more less

NGage B8RII-8 Double Iridium Spark Plug, Universal Fitment The NGage B8RII-8 is a Double Iridium spark plug made in Japan, compatible with BS-4 and BS-6 vehicles. It fits a wide range of mid-to-large displacement motorcycles across Royal Enfield, Triumph, Kawasaki, Yamaha, Bajaj, Benelli, Harley-Davidson, Suzuki, TVS, Aprilia, Jawa, Yezdi, and Hero platforms. If your service manual or mechanic specifies B8RII-8 as the correct plug code, this is the exact component. Technical Specifications Part Number B8RII-8 Brand NGage Powerparts Series Double Iridium Origin Made in Japan Thread Diameter 14 mm Heat Range 8 Electrode Type Double iridium (iridium centre + iridium ground) BS Compliance BS-4 and BS-6 compatible Supplied As Single plug Why Double Iridium Unlike standard iridium plugs that use iridium only on the centre electrode, the B8RII-8 uses iridium on both the centre and ground electrodes. This means: Spark erosion is distributed across both electrodes, significantly longer service life Consistent spark energy throughout the plug's lifespan, not just when new More reliable cold starts and stable combustion at all RPM ranges Suitable for high-displacement engines with higher ignition demand Full Compatibility Reference fitment guidance available per NGage compatibility data. Always cross-reference against your owner's manual or service documentation before purchase. Royal Enfield Himalayan 411 Himalayan 440 Interceptor 650 Continental GT 650 Bear 650 Super Meteor 650 Shotgun 650 Classic 650 Triumph Tiger 1050 Tiger 1050 Sport Sprint GT Speed Triple Speed Triple 1050 Speed Triple R Tiger 1200 Explorer Tiger 1200 XC Tiger 1200 XR Tiger Trophy Kawasaki Ninja 300 Ninja 250R Ninja Z250 Z900 Yamaha YZF R15 (V1, V2, V3 & V4) MT-15 YZF R3 MT-03 Aerox V2 / NVX 155 Bajaj Pulsar 200NS Triple Spark (Side Plugs × 2) Pulsar NS200 Triple Spark (Side Plugs × 2) Pulsar RS200 Triple Spark (Side Plugs × 2) Benelli 502 C TRK 502 TRK 502 X Leoncino 500 Harley-Davidson Street 750 Street Rod 750 Suzuki Suzuki 125 Burgman Suzuki V-Strom 250 TVS Motor Company Apache RTR 160 Apache RTR 180 ABS Aprilia SR 125 SR 150 Jawa Forty Two Bobber 42 350 42 FJ Yezdi Roadster Adventure Scrambler Hero MotoCorp Xpulse 200 2V / 200T Compatibility is specification-based per NGage fitment data. Verify against your service manual before ordering. Bajaj Pulsar NS200, RS200, and 200NS Triple Spark models require 2 units (side plug positions). Installation Notes Verify pre-set gap against your manufacturer's specification before installation Tighten to the torque value specified in your service manual Clean threads before installation; do not over-torque Bajaj Pulsar NS200 / RS200 / 200NS Triple Spark side plug positions require 2 units per bike In The Box 1 × NGage B8RII-8 Double Iridium Spark Plug Terminal Type This plug is supplied with a bare threaded terminal stud. That is how it leaves the factory, and no terminal nut is fitted. A plug cap that screws onto the thread fits as supplied. If your cap seats on a terminal nut instead, a standard screw-on spark plug terminal nut can be fitted to the stud.

Read more less

The Rogue Exhaust for Benelli TNT 600i is the entry point into Barrel's range, a compact slip-on canister that lifts the note without shouting over the engine. This version is made for the Benelli TNT 600i.As a slip-on it keeps the factory headers and catalytic section, so the character stays recognisably your bike's, just with more depth behind it. It is the reversible option: keep the stock can on a shelf and the bike goes back in an afternoon.BuildHigh-temperature ceramic insulation to keep surface heat downFitment guidanceListed by Barrel for the Benelli TNT 600i. Model years and regional variants do differ, so if you are unsure, send us your registration year and a photo of your current exhaust and we will help you check before you order.Good to know An aftermarket exhaust is louder than stock. Check what your local rules allow. Free-flow systems can change fuelling. On some bikes a remap gets the most out of the change. We are an authorized Barrel dealer. Every unit is genuine, supplied direct by Barrel.

Read more less

The Outlaw Exhaust for Benelli 502C with Mid / Link Pipe is Barrel's large-bore line, a wide chamber built for multi-cylinder engines that need volume to breathe. This version is made for the Benelli 502C.As a slip-on it keeps the factory headers and catalytic section, so the character stays recognisably your bike's, just with more depth behind it. It is the reversible option: keep the stock can on a shelf and the bike goes back in an afternoon.Build Stainless steel 304 throughout, so it will not rust through a monsoon Covered by Barrel's warranty Fitment guidanceListed by Barrel for the Benelli 502C. Model years and regional variants do differ, so if you are unsure, send us your registration year and a photo of your current exhaust and we will help you check before you order.Good to know An aftermarket exhaust is louder than stock. Check what your local rules allow. Free-flow systems can change fuelling. On some bikes a remap gets the most out of the change. We are an authorized Barrel dealer. Every unit is genuine, supplied direct by Barrel.

Read more less

The Rogue 2.0 Exhaust for Benelli TNT 600 GT is the revised Rogue, a reworked baffle stack and added heat shielding over the first-generation canister. This version is made for the Benelli TNT 600 GT.As a slip-on it keeps the factory headers and catalytic section, so the character stays recognisably your bike's, just with more depth behind it. It is the reversible option: keep the stock can on a shelf and the bike goes back in an afternoon.Build Stainless steel 304 throughout, so it will not rust through a monsoon Removable DB killer, so you choose the volume Covered by Barrel's warranty Fitment guidanceListed by Barrel for the Benelli TNT 600 GT. Model years and regional variants do differ, so if you are unsure, send us your registration year and a photo of your current exhaust and we will help you check before you order.Good to know An aftermarket exhaust is louder than stock. Check what your local rules allow. Free-flow systems can change fuelling. On some bikes a remap gets the most out of the change. We are an authorized Barrel dealer. Every unit is genuine, supplied direct by Barrel.

Read more less

The Rogue 2.0 Exhaust for Benelli 502C with Decat Pipe is the revised Rogue, a reworked baffle stack and added heat shielding over the first-generation canister. This version is made for the Benelli 502C.As a slip-on it keeps the factory headers and catalytic section, so the character stays recognisably your bike's, just with more depth behind it. It is the reversible option: keep the stock can on a shelf and the bike goes back in an afternoon.Build Stainless steel 304 throughout, so it will not rust through a monsoon Covered by Barrel's warranty Fitment guidanceListed by Barrel for the Benelli 502C. Model years and regional variants do differ, so if you are unsure, send us your registration year and a photo of your current exhaust and we will help you check before you order.Good to know An aftermarket exhaust is louder than stock. Check what your local rules allow. Free-flow systems can change fuelling. On some bikes a remap gets the most out of the change. We are an authorized Barrel dealer. Every unit is genuine, supplied direct by Barrel.

Read more less

The Outlaw 2.0 Exhaust for Benelli Leoncino 500 is the current Outlaw, a 72mm chamber aimed squarely at inline-three and inline-four engines. This version is made for the Benelli Leoncino 500.As a slip-on it keeps the factory headers and catalytic section, so the character stays recognisably your bike's, just with more depth behind it. It is the reversible option: keep the stock can on a shelf and the bike goes back in an afternoon.Build Stainless steel 304 throughout, so it will not rust through a monsoon Removable DB killer, so you choose the volume Covered by Barrel's warranty Fitment guidanceListed by Barrel for the Benelli Leoncino 500. Model years and regional variants do differ, so if you are unsure, send us your registration year and a photo of your current exhaust and we will help you check before you order.Good to know An aftermarket exhaust is louder than stock. Check what your local rules allow. Free-flow systems can change fuelling. On some bikes a remap gets the most out of the change. We are an authorized Barrel dealer. Every unit is genuine, supplied direct by Barrel.

Read more less

Barrel Rogue V2 for the Benelli TRK 251 The Barrel Rogue V2 is a slip-on built specifically for the Benelli TRK 251. Barrel builds in 304 stainless steel and finishes by hand, and the result is a system that changes the character of the bike without asking for a workshop full of tools to fit. Built to Last 304 stainless steel construction Ceramic insulation rated to 1260 degrees Celsius, no refill needed Corrosion resistant, finished to stay presentable Lighter than the stock system Sound You ControlA removable DB killer is included. Leave it in for a deeper, civil note on the daily commute, take it out for the full open sound. The choice stays with the rider rather than being fixed at the factory. Before You Order Professional installation recommended Select the correct configuration before checkout Performance exhausts are louder than stock by design Fitment: listed for the Benelli TRK 251. If you are unsure which configuration suits your bike or your riding, contact us for fitment guidance before you order. We are an authorized Barrel dealer. Every unit is genuine, supplied direct by Barrel.

Read more less

Rolon BPR brass-plated sealed chain and sprocket kit for the Benelli TNT 600i, GT 600 and GTS 600. Supplied as a complete drivetrain set, matched to OE gearing.What's in the kit Brass-plated sealed chain R525HAXRC-118-2 Front sprocket 14T (S 01 849) Rear sprocket 46T (S 02 848), 5 holes Rolon kit reference HAXRC 325 Why the BPR kit Heavy-duty 525 pitch chain sized for the inline four Quadruple-sealed ring construction holds factory grease in and grit out Brass plating for corrosion resistance and a lasting gold finish Rubberised front sprocket damps drivetrain noise and acts as a damper Chain and sprockets wear together and should always be replaced as a set. Message us for fitment guidance if you are unsure which model year you have.

Read more less

Rolon BPR brass-plated sealed chain and sprocket kit for the Benelli TNT 300 and TNT 302R. Supplied as a complete drivetrain set, matched to OE gearing.What's in the kit Brass-plated sealed chain R525HAXRC-108-2 Front sprocket 14T (S 01 849) Rear sprocket 44T (S 01 894), 5 holes Rolon kit reference HAXRC 324 Why the BPR kit Heavy-duty 525 pitch chain sized for the parallel twin Quadruple-sealed ring construction holds factory grease in and grit out Brass plating for corrosion resistance and a lasting gold finish Rubberised front sprocket damps drivetrain noise and acts as a damper Chain and sprockets wear together and should always be replaced as a set. Message us for fitment guidance if you are unsure which model year you have.

Read more less

Rolon BPR brass-plated sealed chain and sprocket kit for the Benelli Imperiale 400. Supplied as a complete drivetrain set, matched to OE gearing.What's in the kit Brass-plated sealed chain R525HORC-109+1 Front sprocket 14T (S 01 963) Rear sprocket 46T (S 02 848), 5 holes Rolon kit reference HORC 367 Why the BPR kit Heavy-duty 525 pitch chain Quadruple-sealed ring construction holds factory grease in and grit out Brass plating for corrosion resistance and a lasting gold finish Rubberised front sprocket damps drivetrain noise and acts as a damper Chain and sprockets wear together and should always be replaced as a set. Message us for fitment guidance if you are unsure which model year you have.

Read more less

CRANK1 performance brake pads for the Benelli TNT Rall in one place, choose your compound (Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli TNT R:Front (2013 Onwards)Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli TNT R?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli 302Rall in one place, choose your compound (Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli 302R:Rear (2018-2020)Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli 302R?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli BN 302all in one place, choose your compound (Ceramic) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli BN 302: Front Rear Front + Rear Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli BN 302?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli TRK 502 Xall in one place, choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli TRK 502 X: Rear (2017-2020) Rear (2022) Front (2022) Front (2017-2020) Front (2021) Rear (2021) Rear (2022-2023) Front + Rear (2017-2020) Front + Rear (2022) Front + Rear (2021) Front + Rear (2022-2023) Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli TRK 502 X?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli TRK 502all in one place, choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli TRK 502: Front (2017 Onwards) Front (Upto 2016) Rear (Upto 2016) Rear (2017 Onwards) Rear (2021 Onwards) Front + Rear (Upto 2016) Front + Rear (2017 Onwards) Front + Rear (2021 Onwards) Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli TRK 502?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli TNT 899all in one place, choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli TNT 899: Front Rear Rear (2017-2019) Front + Rear Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli TNT 899?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli TNT 600iall in one place, choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli TNT 600i: Front Rear Front (2014 Onwards) Rear (2014 Onwards) Front + Rear Front + Rear (2014 Onwards) Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli TNT 600i?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli TNT 300all in one place, choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli TNT 300: Rear Front Rear (2015 Onwards) Front + Rear Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli TNT 300?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli Leoncino 500all in one place, choose your compound (Ceramic) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli Leoncino 500: Rear (2016) Front (2017-2020) Rear (2017-2020) Front (2016) Front + Rear (2016) Front + Rear (2017-2020) Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli Leoncino 500?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli Imperiale 400all in one place, choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli Imperiale 400: Front Rear Rear (2020 Onwards) Front + Rear Front fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli Imperiale 400?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less

CRANK1 performance brake pads for the Benelli 502C Cruiserall in one place, choose your compound (Ceramic & Sintered) and fitment from the selector above. Every CRANK1 pad is HH-rated and engineered to match or surpass OEM stopping power.Ceramic vs Sintered, which should you pick?   Ceramic Sintered Best for Street & touring Aggressive / track / loaded Initial bite Smooth, progressive Strong, immediate High-heat stability Excellent Outstanding Brake dust Low Moderate Rotor wear Gentle on discs Higher Wet performance Strong Strong A Carbon compound is being added to this range and will appear here as an additional option.Fitment guidanceThis listing covers the following fitments for the Benelli 502C Cruiser:RearFront fitments on twin-disc models are supplied as a complete set for both calipers. Choose the option that matches your model year, if you are unsure which set your bike takes, our team is happy to help with fitment guidance before you order.Why CRANK1HH-rated friction • Great initial bite • High-heat stability • Excellent wet handling • Long pad and rotor life • Low brake dustFrequently asked questionsWhich compound should I choose for my Benelli 502C Cruiser?Ceramic suits everyday street and touring with smooth, quiet, low-dust braking that is gentle on rotors. Sintered delivers stronger high-heat bite for aggressive, track or loaded riding.Will these fit my model year?Pick the fitment option that matches your year. Ask us for fitment guidance if you are unsure.Are these genuine CRANK1 pads?Yes, genuine CRANK1 HH-rated pads, developed through years of friction-material research.How do I bed them in?Use progressive braking over the first 150-200 km and avoid hard high-speed stops until the pads are seated.Delivery & returns?Dispatched in 1-2 days with pan-India shipping; 5-day returns.

Read more less