Motorcycle Performance Exhausts

Control Your Exhaust. On Your Terms. Your valved exhaust has two modes — you just haven't been able to use both. The Valvetronic Exhaust Valve Control Module (Manual) gives you a handlebar-mounted switch that physically opens or closes the exhaust butterfly valve whenever you want. Full roar on the open highway. Clean and quiet through the colony, toll booth, or early morning streets. No apps. No wiring. No compromise. This is the most reliable way to control a valved exhaust — because there's nothing electronic to fail. A cable connects your thumb to the valve. That's it. What This Module Does Valved exhausts come with an internal butterfly valve that changes how exhaust gases flow. When the valve is closed, gases pass through a baffled internal route — quieter, more refined. When the valve is open, gases take the free-flow path — louder, rawer, with a more aggressive exhaust note. Most valved exhausts ship without any control module. The valve stays fixed in one position. This module gives you a switch to change it, whenever you want, from the handlebar. Closed valve: Quiet, compliant, neighbour-friendly. Use it in residential areas, at idle, in traffic, on early morning rides. Open valve: The sound your exhaust was built to make. Use it on highways, open roads, or anywhere you want the full character of your exhaust to come through. Why Manual Over Electric Zero electronics. No solenoid, no servo, no wiring loom, no relay. Nothing to short, corrode, or fail over time. Works anywhere, always. The valve opens when you pull the cable. No power required. No sensor needed. Doesn't care if your bike is warm, cold, or idling. You're in control. The valve is exactly where you put it — open or closed — until you choose to change it. No automatic switching when you don't want it. Simple to install. Route the cable, connect to the valve actuator, mount the switch. No ECU tapping, no wiring diagrams, no calibration. Built to last. A cable and a switch outlast any electronic actuator on a motorcycle. Less to maintain, less to replace. How It Works A control switch mounts on your handlebar. A cable runs from the switch down to the butterfly valve actuator on your exhaust. When you flick the switch, cable tension physically rotates the valve between open and closed. The entire system is mechanical — no power draw from your bike's electrical system, no ECU communication, no mapping required. Installation requires routing the cable cleanly along the frame to the exhaust, connecting to the existing valve actuator arm, and adjusting cable tension for full travel in both directions. A standard workshop should be able to install this in under an hour on most platforms. Compatible Bikes This is a universal module — it works with any valved exhaust system that supports mechanical cable actuation, regardless of bike brand or model. Below is a verified compatibility reference across popular Indian market platforms. If your bike has a valved slip-on, this module can control it. Royal Enfield Interceptor 650 / Continental GT 650 / Classic 650 / Bear 650 Classic 350 (Reborn) / Hunter 350 / Meteor 350 Himalayan 411 / Himalayan 450 / Guerrilla 450 Scram 411 / Super Meteor 650 / Shotgun 650 KTM Duke 125 / Duke 200 / Duke 250 / Duke 390 RC 125 / RC 200 / RC 390 Adventure 250 / Adventure 390 / Adventure 390 (2025) 790 Adventure Triumph Speed 400 / Scrambler 400 X / Tiger 400 Street Triple 675 / Speed T4 Bonneville T100 / T120 / Street Twin Tiger 800 / Street Scrambler 900 Yamaha MT-15 V2 / R15 V3 / R15 V4 FZ25 / FZS25 / Fazer 25 MT-03 / R3 YZF-R1 / YZF-R6 / MT-07 Kawasaki Ninja 400 / Ninja 650 / Ninja 1000 SX Z800 / Z900 / Z900 (2026) Versys 650 / Versys-X 300 / Versys 1000 Honda CB200X / CB350 Highness / CB350RS CBR 250R / CB300R / CB300F CBR 650R / CBR 650F / CB Hornet 160R Africa Twin / NX200 Bajaj Pulsar NS200 / RS200 / AS200 / 220F Dominar 250 / Dominar 400 NS 400Z TVS Apache RR 310 / Apache RTR 200 4V Ronin BMW G 310 R / G 310 GS / G 310 RR S 1000 R / S 1000 XR / R 1000 GS Suzuki Gixxer 250 / V-Strom 250SX / V-Strom 650 GSX-R750 / GSX-S750 / GSX-R1000 Hayabusa (2021 Onwards) Ducati Scrambler 800 / Scrambler 1100 Monster 797 / Monster 1200 Hypermotard 939 / Multistrada 950 Streetfighter V4 Harley Davidson Street 750 / Street Rod X440 / X440T Forty Eight / Iron 883 Jawa / Yezdi Jawa 42 FJ / Jawa Perak Yezdi Adventure / Yezdi Roadster Hero Karizma XMR / Xpulse 200 4V / Xpulse 210 Benelli TRK 502 / TRK 502X / TNT 600i / TNT 899 This module is universal — it controls the valve mechanism, not the exhaust itself. Your exhaust must have a butterfly valve with a mechanical actuator arm. Confirm exhaust compatibility before ordering. If your bike model isn't listed but runs a valved slip-on, this module will work. What's in the Box 1 × Valvetronic Manual Control Switch (handlebar mount) 1 × Control cable assembly Mounting hardware Exhaust system not included. Module requires a compatible valved exhaust to function. Specifications Control Type: Manual (mechanical cable) Actuation: Direct cable-pull butterfly valve operation Power Required: None ECU / Wiring Integration: Not required Valve Positions: Open / Closed (user-operated) Mount: Handlebar switch with cable routing Fitment: Universal — compatible with mechanically-actuated valved exhausts Brand: Valvetronic MRP: ₹3,499 Also Available Want automatic valve switching based on RPM and throttle input? The Valvetronic Electric (Automatic) Module does exactly that — the valve opens and closes on its own as you ride. View the Electric Module →

Read more less

Powerage Slip-On Exhaust – Brushed Steel Finish for Royal Enfield Himalayan 411 Unleash the full potential of your Royal Enfield Himalayan 411 with the Powerage Slip-On Exhaust – Brushed Steel Finish, engineered for riders who demand stronger mid-range pull, sharper throttle response, and a deeper, more authoritative exhaust note without compromising reliability. Designed specifically for the Himalayan 411 platform, this slip-on exhaust system enhances exhaust gas evacuation while maintaining the precise back-pressure required for usable torque delivery. The result is a cleaner, more responsive power curve with improved throttle control across city traffic, highway cruising, and demanding off-road terrain. Crafted from high-grade stainless steel, finished in a premium brushed steel outer sleeve, and paired with a black powder-coated end cap, the Powerage Slip-On combines durability with a rugged, adventure-ready aesthetic. It resists corrosion, withstands repeated heat cycles, and maintains structural integrity under vibration-heavy riding conditions. Engineered for Real-World Torque The Himalayan 411 thrives on accessible torque rather than peak dyno figures. This exhaust is tuned accordingly. The internal baffle structure is calibrated to: • Maintain optimal back pressure• Improve throttle response consistency• Enhance mid-range torque feel• Deliver smoother roll-on acceleration• Support stable combustion under load Instead of chasing aggressive top-end spikes, the Powerage Slip-On improves how the bike feels in practical riding scenarios. Climbing gradients, navigating traffic, overtaking on highways, or riding fully loaded — throttle input becomes more predictable and controlled. Acceleration feels cleaner. Gear transitions feel more deliberate. Low-speed modulation improves in off-road conditions where traction sensitivity matters. Sound Profile – Deep, Controlled, Mechanical This is not a shrill or hollow exhaust note. The Powerage Slip-On produces a deep, bass-oriented exhaust tone that complements the Himalayan’s long-stroke single-cylinder engine. The sound remains full-bodied and mechanical without excessive rasp or metallic sharpness. Included is a removable dB reducer, allowing you to tailor output depending on: • Urban commuting• Long-distance touring• Trail riding• Local sound compliance requirements With the dB killer installed, the tone remains controlled and road-friendly.Without it, the exhaust develops a fuller, more assertive presence while retaining tonal depth. Construction & Material Integrity Each unit is handcrafted and dyno-tested to ensure consistent performance output and manufacturing quality. Material & Build Highlights: • Full stainless steel construction for rust resistance• Brushed steel finish for long-term durability• Black powder-coated end cap for added heat resistance• Reinforced weld joints for structural stability• Vibration-resistant mounting configuration• Heat-stable internal baffle assembly The brushed exterior ages gracefully and maintains a premium appearance even after exposure to mud, dust, rain, and long-distance touring. This is built for Indian riding conditions — high ambient temperatures, varied terrain, and extended operating hours. Direct Bolt-On Fitment Installation is straightforward and non-invasive. • No cutting• No welding• No ECU remap required• Uses factory mounting points The system is engineered as a direct replacement slip-on exhaust for the Royal Enfield Himalayan 411. Fitment alignment ensures correct clearance with frame components, swingarm movement, and rear suspension travel.As confirmed by Powerage technical support, this exhaust is also compatible with the Royal Enfield Scram 411 platform. All required mounting hardware (nuts, bolts, clamps) is included as supplied by the manufacturer. The entire process remains reversible if needed. Ride Experience Transformation Post-installation improvements are felt more than measured. • Stronger low-to-mid RPM response• More engaging throttle feel• Cleaner power delivery under load• Deeper mechanical exhaust character• Reduced stock exhaust weight• Sharper visual presence The Himalayan shifts from subdued to confident. Not louder for the sake of noise — but tuned for presence and response. This is an upgrade focused on riding feel, not just decibels. Technical Specifications Material: Stainless SteelFinish: Brushed Steel with Black Powder-Coated End CapFitment: Royal Enfield Himalayan 411Installation Type: Direct Bolt-OnSound Control: Removable dB Reducer IncludedDesign: Back-pressure optimized internal baffle systemApplication: Road and off-road use What’s Included • Powerage Slip-On Exhaust (Brushed Steel Finish)• Stainless steel mounting hardware• Removable dB reducer Warranty & Authenticity This product is covered under the official manufacturer warranty as per Powerage policy. RawTorque supplies genuine products sourced through authorized distribution channels. RawTorque does not provide independent warranty coverage beyond the manufacturer’s terms. For complete details, refer to the Warranty Policy.

Read more less

Built for the Bear 650 Twin Engine The Barrel B-20 Bass Master Exhaust is engineered specifically for the Royal Enfield Bear 650 platform. This is not just a slip-on—it’s a performance-focused system with a decat pipe designed to unlock the full breathing potential of the 650 twin engine. 🔊 Signature Bass Master Sound Deep, bass-heavy exhaust tone Strong low-frequency thump No sharp or raspy noise This is tuned for authority, not noise pollution. ⚙️ Decat Performance Advantage Unlike standard slip-ons, this setup includes a decat pipe: Frees up exhaust flow Reduces back pressure Improves engine breathing Enhances throttle response Result → smoother, more responsive acceleration ⚡ Performance Gains You Can Feel Noticeably sharper throttle response Improved torque delivery More engaging riding experience No unnecessary tuning complexity—just real-world gains. 🪶 Weight Reduction & Build Quality Saves approx 1.5–5.5 kg vs stock Constructed from 304 Stainless Steel High durability + corrosion resistance 🛠️ Plug & Play Fitment Direct bolt-on installation (OEM mounts) No cutting or welding required Installation time: ~30–45 minutes 🔧 DB Killer Control Comes with removable DB killer Tune sound based on preference: With DB killer → controlled Without → full bass roar 📦 What’s in the Box B-20 Bass Master Exhaust Decat Pipe DB Killer Mounting Hardware ✅ Compatibility Royal Enfield Bear 650 ⚠️ Important Notes This is a performance exhaust with decat pipe May not comply with emission or noise regulations in all regions ECU remap is not mandatory, but can help extract optimal performance Sound output will be significantly louder than stock 🛡️ Warranty Manufacturer Warranty: Lifetime rust warranty 1-year weld warranty RawTorque Note:RawTorque does not provide any additional warranty beyond the manufacturer’s coverage.For more details, please refer to our warranty policy.

Read more less

Barrel Rogue Slip-On Exhaust for KTM Duke 250/390, RC 390 & Adventure 390 – Stainless Steel (Rogue 1.0 & 2.0) The Barrel Rogue Exhaust for KTM Duke 250, Duke 390, RC 390 and Adventure 390 is a stainless steel slip-on exhaust system designed as a direct rear-section replacement. This listing covers both Rogue 1.0 and Rogue 2.0 styles with model-specific fitment options via the variant dropdown. This exhaust replaces the stock rear canister and includes a compatible link pipe matched to your selected model. It modifies the visual profile and acoustic output while retaining the original header system. Compatible KTM Models — Select Correct Variant KTM Duke 250 KTM Duke 390 BS4 KTM Duke 390 BS6 KTM RC 390 BS4 KTM RC 390 BS6 KTM Adventure 390 Fitment depends on selecting the correct variant. Confirm your model and BS4 / BS6 configuration before ordering. Not compatible with KTM models equipped with factory underbelly exhaust systems. Rogue 1.0 vs Rogue 2.0 Rogue 1.0 Compact canister design with shorter rear profile Sharper, more aggressive exhaust character Stainless steel, black finish Rogue 2.0 Revised canister geometry with altered internal acoustic tuning Fuller, deeper exhaust tone Stainless steel, black finish Construction & Materials Built from stainless steel — durable, corrosion-resistant, handles repeated heat cycles and daily exposure. Includes a model-specific link pipe connecting the canister to the existing mid-section. Slip-on configuration — rear muffler replacement only, original header stays. Sound & Performance By modifying the internal chamber and exhaust flow path, the Rogue produces a more pronounced tone compared to stock. Sound intensity varies by model, fuel mapping, catalytic configuration, and DB killer setting. Comes with a removable DB killer for sound adjustment. As a slip-on, this primarily affects acoustics and rear-end weight. Any perceived change in throttle response varies by overall bike configuration. Does not include ECU remapping or fuel controllers — arrange tuning separately if required. Compliance with local noise regulations is the owner's responsibility. Installation Remove factory exhaust canister Connect supplied link pipe Mount the Rogue canister and secure hardware to torque spec Check alignment and exhaust sealing Professional installation recommended. No permanent engine modification required. What's in the Box Rogue Exhaust Canister (1.0 or 2.0 as selected) Model-specific link pipe Mounting hardware Removable DB killer Specifications Brand: Barrel Exhaust Type: Slip-On Exhaust Material: Stainless Steel Finish: Black Styles: Rogue 1.0 / Rogue 2.0 Fitment: KTM Duke 250, Duke 390 BS4/BS6, RC 390 BS4/BS6, Adventure 390

Read more less

Powerage Slip-On Exhaust for Royal Enfield Himalayan 450 (Sherpa 450 Platform) Transform the Himalayan 450’s character with the Powerage Slip-On Exhaust, engineered specifically for riders who demand sharper throttle response, stronger mid-range pull, and a deeper, more authoritative exhaust note. Built around the Sherpa 450 platform, this system enhances exhaust flow while maintaining engine reliability — delivering a cleaner, more responsive power curve on both road and trail. The Himalayan 450 is a torque-focused machine. It thrives on usable power, not peak numbers. The Powerage Slip-On complements that philosophy by reducing back pressure and optimizing flow dynamics, allowing the engine to breathe more efficiently. The result is noticeably improved roll-on acceleration, stronger response during overtakes, and a more connected throttle feel — especially in mid-range RPMs where adventure riding lives. Whether your bike runs a Single O₂ Sensor (2024 models) or a Dual O₂ Sensor setup (2025 onwards), this exhaust is engineered with precise variant-specific compatibility. Proper sensor integration ensures smooth fueling behavior and stable rideability across altitude changes and varied terrain conditions. Engineered Benefits • Noticeably quicker throttle response• Improved mid-range torque delivery• Stronger roll-on acceleration• Deeper, bass-rich exhaust tone• More controlled engine heat dispersion• Enhanced riding feel during climbs and highway cruising This is not just about sound. It is about refining the way the Sherpa 450 feels under load. Complete Fitment System The Powerage Slip-On comes as a complete installation kit. Included in the package: • Exhaust canister• Bend pipe (model specific)• Clamps and mounting hardware• Removable DB killer• Required chims• Branded Powerage sticker Everything is designed for direct bolt-on installation using factory mounting points. No cutting. No welding. No ECU remap required. Installation is straightforward and can typically be completed with basic hand tools. The system aligns cleanly with the stock mounting geometry, ensuring proper clearance from swingarm, rear brake assembly, and chassis components. Tuned for Real-World Riding The Himalayan 450 is built for versatility — city traffic, broken tarmac, gravel tracks, mountain climbs. This slip-on is tuned to maintain rideability across all of it. The internal flow path is engineered to maintain adequate back pressure for torque retention while improving exhaust evacuation efficiency. That balance is critical on a single-cylinder engine. Too free-flowing, and you lose tractability. Too restrictive, and you choke response. This system finds the middle ground. Expect a more alive throttle response when exiting corners. Expect cleaner engine feel during sustained highway cruising. Expect stronger pull in 3rd and 4th gear during overtakes. Deep, Controlled Sound Signature Fitted with a removable DB killer, the exhaust allows you to tailor sound output based on riding conditions and regulatory requirements. With DB killer installed:• Deep, bass-heavy tone• Refined note suitable for touring Without DB killer:• More aggressive exhaust presence• Stronger low-frequency thump The sound profile is tuned to be full-bodied — not tinny, not hollow. It complements the Himalayan’s long-stroke character without becoming harsh at higher RPMs. Built for Adventure Conditions Constructed from high-quality heat-resistant materials, the Powerage Slip-On is designed to withstand: • Continuous vibration• Long riding hours• Temperature swings• Dust and off-road conditions The mounting structure maintains stability even during rough terrain riding. The finish is engineered to resist corrosion under typical Indian weather and road conditions. Rider-Focused Advantages • Stronger power delivery in loaded touring scenarios• Improved responsiveness during technical off-road sections• Enhanced throttle modulation for slow-speed control• A rugged, performance-oriented visual upgrade The Himalayan 450 is not a showpiece. It is a working machine. This exhaust respects that identity while sharpening its personality. Fitment Compatibility Royal Enfield Himalayan 450 (Sherpa 450 Platform)• Single O₂ Sensor Variant (2024)• Dual O₂ Sensor Variant (2025 onwards) Please select the correct sensor configuration before checkout to ensure proper fitment. Ride harder. Ride cleaner. Sound deliberate. The Powerage Slip-On Exhaust for Royal Enfield Himalayan 450 is built for riders who want performance refinement without compromising reliability — a balanced upgrade that feels engineered, not improvised.

Read more less

Red Rooster Performance Rumbler Max Black Exhaust for Royal Enfield Hunter 350 The Red Rooster Performance Rumbler Max Black Exhaust for Royal Enfield Hunter 350 is a high-quality slip-on exhaust system. It is designed for riders seeking the perfect balance between sound character, build quality, and daily usability. Made by Red Rooster Performance, this exhaust integrates cleanly with the Hunter 350 while enhancing rideability and long-term durability. Exhaust systems affect not only the sound but also heat management, durability, and the overall riding experience. The Rumbler Max Black acts as a direct-fit replacement for the stock exhaust. This allows riders to upgrade their Royal Enfield Hunter exhaust without permanent modifications. Compatibility with the original mounting points and exhaust routing is maintained, which supports easy servicing and reversibility. Material Construction and Finish of the Royal Enfield Hunter Exhaust The Rumbler Max Black is crafted using Grade 304 stainless steel. This material is widely used in performance exhausts for its corrosion resistance and ability to withstand heat cycling. Stainless steel ensures the exhaust handles repeated thermal expansion and contraction during everyday rides and highway use without fatigue. The matte black finish complements the Hunter 350’s design with a clean, performance-focus look. When cared for properly, this finish retains its quality and appearance over long-term use under normal riding conditions. The subtle look fits well with the motorcycle’s aesthetic. Sound Character and Riding Experience Red Rooster Performance’s exhaust systems emphasize controlled sound output rather than simply increasing volume. The Rumbler Max Black delivers a deeper and more distinct exhaust note than the stock unit. Despite the heightened sound, it remains practical and unobtrusive for regular riding. This Royal Enfield Hunter exhaust includes ceramic wool packing inside. This material can handle high temperatures and vibrations for extended periods. Ceramic wool helps maintain the consistent exhaust tone as the system matures, minimizing sound degradation over normal use. Note that sound perception will vary based on riding environment, throttle usage, traffic, and external factors. Riders should always comply with local noise laws and regulations when installing aftermarket exhausts. Designed for Direct Bolt-On Installation The Red Rooster Performance Rumbler Max Black Exhaust is built for direct bolt-on installation on the Royal Enfield Hunter 350. No cutting, welding, or permanent modifications are required. This design makes it easy for riders to fit the new exhaust quickly and safely. Because it uses the motorcycle’s existing mounting points, the exhaust can be installed or removed without altering the bike’s original structure. This makes the upgrade suitable for riders who want reversible changes or may want to switch back to the stock exhaust later. Heat Resistance and Long-Term Durability Motorcycle exhausts regularly face intense heat, vibration, and environmental elements such as road debris and moisture. The stainless steel construction paired with ceramic wool packing keeps the Rumbler Max Black strong and acoustically consistent over time. The design supports daily commuting and weekend rides without performance drops caused by heat fatigue or material wear. Proper installation and maintenance ensure its durability for long-term use as an effective Royal Enfield Hunter exhaust upgrade. Compatibility and Intended Use This exhaust is designed specifically for the Royal Enfield Hunter 350. Its fitment relies on the stock exhaust layout and mounting geometry unique to this model. Use on other motorcycles is not recommended unless confirmed by the manufacturer. Functioning as a purely mechanical component, the Rumbler Max Black does not include any electronic parts. It does not require ECU remapping for regular installation conditions. Actual sound and riding feel may change depending on usage style, fuel quality, and bike condition. Installation and Ownership Considerations Installation should follow proper procedures to guarantee correct alignment, sealing, and mounting security. Exhaust fasteners should be periodically checked, especially soon after installation and during regular servicing. As with all aftermarket Royal Enfield Hunter exhaust upgrades, riders must ensure the bike complies with applicable local traffic, emission, and noise regulations when using this exhaust system. What’s Included The kit contains one Red Rooster Performance Rumbler Max Black Exhaust unit. It is tailored for direct installation on the Royal Enfield Hunter 350. Mounting components in the kit securely integrate with the factory exhaust setup, ensuring a smooth fit and performance upgrade.

Read more less

The Interceptor 650's twin exhaust gets a proper upgrade — Norifumi GTX slip-on, built for the parallel twin. The Norifumi GTX is a slip-on exhaust for the Royal Enfield Interceptor 650, designed to suit the character of the parallel twin — deeper, more defined exhaust note with a weight reduction over the heavy OEM canister. The GTX design is Norifumi's boulevard-sport spec: a clean stainless steel canister profile that complements the Interceptor's retro-modern aesthetic while delivering better exhaust flow. What's in the box: GTX canister (stainless steel) Stainless steel link pipe All fitment hardware Why Norifumi GTX: 650cc parallel twin tuned: Exhaust character matched to the Interceptor's engine note Weight reduction: Lighter than the OEM canister assembly Better flow: Freer-breathing exhaust vs. stock restrictive muffler Stainless steel: Long-term durability and resistance to heat cycling Genuine Norifumi: Authorised distributor stock, MRP inclusive of 18% GST Compatible Bike: Royal Enfield Interceptor 650 (all years) Note: This is a single canister slip-on. The Interceptor 650 runs twin exhausts — one unit per side. Sold per piece.

Read more less

All the Whoops SS — with a carbon fibre end cap. Same Himalayan-ready build, sharper finish. The Norifumi Whoops SS Carbon is the carbon end-cap variant of the Himalayan 450 Whoops slip-on — stainless steel canister body with a carbon fibre exit cap for a premium visual finish. Available in Short and Long configurations. Everything else is identical to the Whoops SS: stainless steel link pipe, complete fitment hardware, and Norifumi's characteristic adventure-tuned sound profile. The Short version sits tighter to the bike — better for luggage and pannier setups. The Long version has a more commanding canister profile and deeper note. What's in the box: Whoops SS Carbon canister (stainless body + carbon fibre end cap) Stainless steel link pipe All fitment hardware (brackets, clamps, heat shield) Why Norifumi Whoops SS Carbon: Carbon end cap: Premium finish over the standard Whoops SS — same performance, better aesthetics Weight reduction: Lighter than OEM canister and mid-section assembly Better flow: Improved exhaust scavenging vs. stock Stainless + carbon build: Durable in the conditions the Himalayan rides in Genuine Norifumi: Authorised distributor stock, MRP inclusive of 18% GST Compatible Bike: Royal Enfield Himalayan 450 (2024 onwards) For the standard stainless finish without carbon cap, see EXH18155 (Short) and EXH18157 (Long).

Read more less

The Himalayan 450's OEM exhaust was always the weakest link. The Norifumi Whoops SS fixes that. The Norifumi Whoops SS is a stainless steel slip-on exhaust for the Royal Enfield Himalayan 450 — available in Short and Long configurations. The Whoops canister is Norifumi's benchmark adventure exhaust: purpose-built for bikes that go off the road, with stainless steel construction, a bolt-on link pipe, and a sound profile that suits the Himalayan's character without being intrusive. The Short version offers a cleaner, tucked fitment with slightly less visual presence — ideal for rack-and-luggage setups. The Long version delivers a more substantial canister with additional sound and character. What's in the box: Whoops SS canister (stainless steel) Stainless steel link pipe All fitment hardware (brackets, clamps, heat shield) Why Norifumi Whoops SS: Weight reduction: Meaningfully lighter than the OEM canister and mid-section Better flow: Improved exhaust scavenging — sharper throttle response Adventure-ready construction: Stainless steel — built for the conditions the Himalayan is designed for Two length options: Short for luggage-carry setups, Long for maximum presence Genuine Norifumi: Authorised distributor stock, MRP inclusive of 18% GST Compatible Bike: Royal Enfield Himalayan 450 (2024 onwards) For the Carbon fibre end-cap version, see EXH18156 (Short) and EXH18158 (Long).

Read more less

The XPulse 210's most aggressive exhaust option — Norifumi's top-spec Kompetisi canister, full system. The Norifumi Rocket4 Kompetisi is the top-of-range full exhaust for the Hero XPulse 210. The Kompetisi spec runs a larger, competition-tuned canister compared to the Boreup variant — delivering a more aggressive exhaust note and greater power potential at the top end. Built in stainless steel for off-road durability. DB Killer included for road compliance. What's in the box: Full exhaust system — headers + midpipe + canister Rocket4 Kompetisi canister (stainless steel) DB Killer (removable) All fitment hardware Why Norifumi Rocket4 Kompetisi: Competition spec: Larger, more aggressive canister vs. Boreup — more top-end output Full system weight reduction: Noticeably lighter than OEM exhaust assembly Dual-sport ready: DB Killer included — compliant for road, removable for trail Stainless steel construction: Long-term durability in off-road conditions Genuine Norifumi: Authorised distributor stock, MRP inclusive of 18% GST Compatible Bike: Hero XPulse 210 (2024 onwards) For the more road-biased Boreup option, see EXH21059.

Read more less

Royal Enfield Classic 350 Reborn Replica Exhaust Black – Moto Torque Product Description The Moto Torque Replica Exhaust for Royal Enfield Classic 350 Reborn (Black) is designed specifically for the Royal Enfield Classic 350 Reborn platform. This exhaust follows a replica-style design intended to maintain a traditional exhaust silhouette while offering a darker exterior finish. The Royal Enfield Classic 350 Reborn Replica Exhaust Black features an elongated exhaust body that closely resembles the stock exhaust profile used on Royal Enfield motorcycles. The black exterior finish provides a darker visual appearance compared to chrome exhaust variants. This exhaust is described as a performance-oriented replica exhaust and includes ceramic blanket insulation as part of its internal construction. The insulation forms part of the internal assembly of the exhaust unit. For riders looking to install a replica-style black exhaust specifically for the Royal Enfield Classic 350 Reborn, this Moto Torque exhaust provides a replacement exhaust option designed around the Classic 350 Reborn exhaust layout. Warranty Disclaimer This product does not carry any manufacturer warranty. Rawtorque does not provide any additional warranty coverage for this product. Please refer to our Warranty Policy for complete terms and conditions. Specifications Brand: Moto Torque Product Type: Motorcycle Exhaust Motorcycle Compatibility: Royal Enfield Classic 350 Reborn Finish: Black Insulation: Ceramic Blanket Insulation Installation Type: Replacement Exhaust

Read more less

Moto Torque Replica Black Exhaust for Royal Enfield (BS6) – Black Finish Product Description The Moto Torque Replica Black Exhaust (BS6) is designed for riders who prefer a stock-style exhaust profile with a deeper bass tone while maintaining a dark exterior finish. The exhaust follows a replica-style design that closely resembles the traditional Royal Enfield exhaust layout. The Moto Torque Replica Black Exhaust BS6 is described as a performance-oriented exhaust and features ceramic blanket insulation as part of its internal construction. This insulation forms part of the exhaust assembly and supports the internal structure of the unit. The exhaust comes with a black finish, giving the motorcycle a darker exhaust appearance compared to chrome variants. The elongated replica-style body maintains the familiar exhaust silhouette commonly associated with Royal Enfield motorcycles. For riders looking for a replica-style black exhaust compatible with BS6 motorcycles, this Moto Torque Replica Black Exhaust provides a replacement exhaust option with ceramic insulation and a black exterior finish. Warranty Disclaimer This product does not carry any manufacturer warranty. Rawtorque does not provide any additional warranty coverage for this product. Please refer to our Warranty Policy for complete terms and conditions. Specifications Brand: Moto Torque Product Type: Motorcycle Exhaust Version: BS6 Finish: Black Insulation: Ceramic Blanket Insulation Installation Type: Replacement Exhaust

Read more less

Moto Torque Replica Black Exhaust for Royal Enfield (BS4) – Black Finish Product Description The Moto Torque Replica Black Exhaust (BS4) is designed for riders who prefer a stock-style exhaust profile with a deeper bass tone while maintaining a dark finish. The exhaust follows a replica-style design that closely resembles the traditional Royal Enfield exhaust silhouette. Constructed as a performance-oriented exhaust, the Moto Torque Replica Black Exhaust BS4 features ceramic blanket insulation within its internal structure. The insulation forms part of the exhaust assembly and supports the internal configuration of the unit. The exhaust comes with a black finish, giving it a darker appearance compared to chrome variants while maintaining the long replica-style body design. The overall layout follows the familiar exhaust shape commonly associated with Royal Enfield motorcycles. For riders looking for a replica-style black exhaust compatible with BS4 motorcycles, this Moto Torque Replica Black Exhaust offers a replacement exhaust option with ceramic insulation and a black exterior finish. Warranty Disclaimer This product does not carry any manufacturer warranty. Rawtorque does not provide any additional warranty coverage for this product. Please refer to our Warranty Policy for complete terms and conditions. Specifications Brand: Moto Torque Product Type: Motorcycle Exhaust Version: BS4 Finish: Black Insulation: Ceramic Blanket Insulation Installation Type: Replacement Exhaust

Read more less

Moto Torque Replica Chrome Exhaust for Royal Enfield (BS6) – Chrome Finish Product Description The Moto Torque Replica Chrome Exhaust (BS6) is designed for riders who prefer a stock-style exhaust appearance with a deeper bass tone. This exhaust follows a replica-style design that closely resembles the traditional Royal Enfield exhaust profile. The Moto Torque Replica Chrome Exhaust BS6 is described as a performance-oriented exhaust and is constructed with ceramic blanket insulation within its internal structure. The insulation forms part of the exhaust assembly and is intended to support the exhaust’s internal configuration. The exhaust features a chrome exterior finish, giving it a polished metallic appearance that complements classic motorcycle styling. The long replica design maintains the familiar silhouette associated with Royal Enfield exhaust systems. For riders looking for a replica-style chrome exhaust compatible with BS6 motorcycles, this Moto Torque Replica Chrome Exhaust offers a replacement exhaust option with ceramic insulation and chrome finish. Warranty Disclaimer This product does not carry any manufacturer warranty. Rawtorque does not provide any additional warranty coverage for this product. Please refer to our Warranty Policy for complete terms and conditions. Specifications Brand: Moto Torque Product Type: Motorcycle Exhaust Version: BS6 Finish: Chrome Insulation: Ceramic Blanket Insulation Installation Type: Replacement Exhaust

Read more less

Moto Torque Replica Chrome Exhaust for Royal Enfield (BS4) – Chrome Finish Product Description The Moto Torque Replica Chrome Exhaust (BS4) is designed for riders who prefer a stock-style exhaust appearance with a deeper bass tone. This replica-style exhaust maintains the classic Royal Enfield exhaust look while offering a different sound character. The Moto Torque Replica Chrome Exhaust BS4 is described as a performance-oriented exhaust and is built with ceramic blanket insulation as part of its internal construction. The insulation forms a protective layer within the exhaust assembly. Finished in chrome, the exhaust maintains a polished appearance that complements motorcycles styled with classic or retro design elements. The elongated replica design closely follows the traditional exhaust form factor. For riders looking for a replica-style chrome exhaust for BS4 motorcycles, this Moto Torque Replica Chrome Exhaust provides a chrome-finished replacement exhaust option with insulated internal construction. Warranty Disclaimer This product does not carry any manufacturer warranty. Rawtorque does not provide any additional warranty coverage for this product. Please refer to our Warranty Policy for complete terms and conditions. Specifications Brand: Moto Torque Product Type: Motorcycle Exhaust Version: BS4 Finish: Chrome Insulation: Ceramic Blanket Insulation Installation Type: Replacement Exhaust

Read more less

Engineered for Honda CB350 Platform The Red Rooster Pegasus Max Exhaust is precision-crafted for the Honda CB350(including Special Editions). Designed to enhance both sound and ride feel, this performance exhaust delivers a balanced upgrade without compromising daily usability. Signature Deep Thump This is where the transformation happens. Deep, throaty exhaust tone Classic long-stroke character enhancement Refined—not harsh, not noisy It complements the CB350’s DNA instead of overpowering it. Performance That You Feel Up to ~10% improved throttle response Smoother acceleration delivery Better mid-range pull No artificial tuning—just optimized exhaust flow. Lightweight Advantage Noticeably lighter than stock exhaust Improves handling agility Reduces rear-end weight bias Built for Longevity Premium stainless steel construction Rust-resistant finish Designed for Indian riding conditions Plug & Play Installation Direct bolt-on fit No cutting, no welding No ECU remap required Installs on stock setup Compatibility Direct Fitment: Honda CB350 (incl. Special Editions) Variants (Finish Options) Polish – Chrome-like premium shine Black – Stealth, aggressive look Matte – Understated clean finish ⚠️ Important Notes This is a performance exhaust (slip-on) Sound output may vary based on riding conditions Check local regulations before use

Read more less

Precision Performance Exhaust for Dominar 250 & 400 The Red Rooster Altair Exhaust is purpose-built for riders who want their Bajaj Dominar to feel alive. Designed for both Dominar 250 and Dominar 400, this performance slip-on transforms your ride with a deeper exhaust tone, reduced weight, and improved throttle response—all while retaining plug-and-play simplicity. Crafted using premium SS304 stainless steel and high-grade insulation materials, the Altair is engineered to balance performance, durability, and sound character in one refined system. Sound That Commands Presence This isn’t noise—it’s character. The Altair delivers a deep, throaty, bass-heavy exhaust note that enhances the muscular identity of the Dominar. Whether cruising highways or rolling through the city, the sound stays refined, aggressive, and unmistakably premium. Performance Without Complexity No remap. No tuning drama. Just bolt-on gains. Up to ~10% improvement in throttle response & engine feel Optimized airflow for smoother combustion cycles Immediate response across low and mid-range You feel it the moment you twist the throttle. Lightweight Engineering Advantage Stock exhausts carry unnecessary bulk. The Altair trims that down. Approx weight: ~2.4 kg Significant reduction vs stock unit Improves handling agility and balance Less weight. More control. Built to Endure Material: SS304 Stainless Steel Rust-resistant, long-life construction Heat-resistant internal packing Designed for Indian riding conditions—traffic, heat, highways Effortless Installation Direct bolt-on fitment No cutting or modification required Compatible with stock setup Installation time: ~30–45 minutes Compatibility Direct Fitment For: Bajaj Dominar 400 Bajaj Dominar 250 Variants (Finish Options) Polish – Classic metallic shine Matte – Subtle, understated finish Black – Aggressive stealth look ⚠️ Important Note This is a performance exhaust (slip-on unit), not a full system Sound output may vary based on riding conditions Ensure compliance with local regulations before use

Read more less

Upgrade your Royal Enfield motorcycle with the Powerage Long Type Slip-On Exhaust, designed for riders who want a classic elongated exhaust profile combined with deeper exhaust acoustics, improved exhaust flow, and premium stainless steel construction. The long-type design delivers a more traditional Royal Enfield exhaust silhouette while enhancing the motorcycle’s visual presence and exhaust character. Engineered specifically for Royal Enfield 350 and 500 motorcycles, this exhaust system improves throttle response and provides a richer bass-heavy exhaust note without compromising everyday rideability. Dyno-tested and handcrafted using high-grade stainless steel materials, the Powerage Long Type exhaust balances classic styling with performance-focused engineering. This listing includes multiple finish variants under one product listing: Polish Finish Brushed Steel Finish Black Finish Each variant delivers the same internal construction and performance characteristics while offering a different visual finish for custom styling preferences. Finish Options Polish Finish Mirror-finished stainless steel appearance for riders seeking a premium retro chrome-inspired look. Brushed Steel Finish Industrial brushed stainless steel finish with rugged aesthetics and lower visible scratch appearance. Black Finish Aggressive matte black finish designed for stealth-themed and dark custom motorcycle builds. Key Features Compatible with Royal Enfield 350 & 500 motorcycles Long-type classic exhaust styling Deep resonant exhaust note Stainless steel construction Dyno-tested exhaust setup Improved throttle response Hand-crafted build quality Detachable dB reducer included Optimized baffle core design Synthetic wool acoustic insulation Bolt-on fitment OE-inspired aesthetics Performance Benefits The Powerage Long Type exhaust improves exhaust flow efficiency while maintaining smooth rideability for daily use and highway touring. Its elongated internal chamber design helps create a fuller and deeper exhaust note while supporting smoother mid-range power delivery and reduced exhaust restriction compared to stock systems. The exhaust also contributes to reduced overall system weight and enhanced visual appeal. Construction & Engineering Built using premium stainless steel internals and outer shell construction, the Powerage exhaust is engineered for long-term durability and corrosion resistance. The detachable dB reducer allows riders to customize the exhaust sound profile depending on riding conditions and sound preference. Its handcrafted construction quality ensures consistent fitment and premium finish detailing across all variants. Package Contents 1 x Powerage Slip-On Exhaust (Long Type) Mounting Bracket Exhaust Clamp Detachable dB Reducer Installation Hardware Important Note Select preferred finish variant before placing the order. Compatible with selected Royal Enfield 350 & 500 motorcycles only. Professional installation recommended. Exhaust sound characteristics may vary depending on dB reducer usage.

Read more less

Upgrade the sound, styling, and performance character of your Royal Enfield motorcycle with the Powerage Slip-On Exhaust Short Type edition, engineered for riders who want a deeper exhaust tone, lighter exhaust setup, and aggressive retro styling without compromising everyday usability. Designed specifically for Royal Enfield 350 and 500 platforms, this short-type slip-on exhaust delivers a compact performance-oriented profile with improved exhaust acoustics and optimized back pressure management. Manufactured using premium stainless steel construction and dyno-tested for reliable real-world performance, the Powerage exhaust system improves throttle feel while adding a richer and more resonant exhaust note. The compact short-type body design gives the motorcycle a cleaner and more aggressive stance while helping reduce overall exhaust bulk compared to stock systems. This listing includes multiple finish options under one product listing: Polish Finish Brushed Steel Finish Black Finish Each finish offers a distinct visual character while retaining the same core internal performance-focused design. Finish Options Polish Finish Mirror-polished stainless steel finish designed for riders who prefer a premium retro-inspired appearance. Brushed Steel Finish Industrial satin stainless steel finish with excellent resistance to scratches and daily wear. Black Finish Stealth-inspired matte black coating for aggressive styling and darker custom builds. Key Features Compatible with Royal Enfield 350 & 500 models Short-type compact exhaust design Deep resonant exhaust note Stainless steel construction Dyno-tested setup Improved throttle response Hand-crafted construction Detachable dB reducer included Optimized baffle core design Synthetic wool acoustic insulation Bolt-on installation OE-inspired fitment styling Performance Benefits The Powerage Short Type exhaust is engineered to improve exhaust flow efficiency while maintaining balanced rideability for everyday road use. Its compact internal baffle system helps create a bass-heavy exhaust note while preserving smoother low-end response and usable mid-range performance. The lighter construction compared to stock systems also helps improve the motorcycle’s overall feel and handling response. Construction & Engineering Manufactured using premium-grade stainless steel internals, the Powerage slip-on exhaust combines durability, corrosion resistance, and optimized acoustic insulation for long-term reliability. The detachable dB reducer allows riders to choose between a refined touring sound and a louder performance-oriented exhaust tone. Its handcrafted construction and precision weld quality provide excellent fitment consistency and premium visual appeal. Package Contents 1 x Powerage Slip-On Exhaust (Short Type) Mounting Bracket Exhaust Clamp Detachable dB Reducer Installation Hardware Important Note Select the preferred finish variant before ordering. Compatible with selected Royal Enfield 350 & 500 motorcycles only. Professional installation recommended. Exhaust note may vary depending on dB reducer installation and engine condition.

Read more less

Enhance the sound, styling, and riding experience of your Royal Enfield Classic Reborn 350 or Meteor 350 with the Powerage Slip-On Exhaust system engineered for improved exhaust flow, reduced weight, and deeper exhaust acoustics. Manufactured using premium stainless steel construction and dyno-tested for balanced real-world performance, the Powerage exhaust system delivers a stronger exhaust note, improved throttle feel, and cleaner premium aesthetics while maintaining everyday usability. Its internally engineered baffle core provides optimized back pressure and exhaust efficiency, helping preserve smooth rideability while unlocking a richer and deeper exhaust character. The exhaust includes a detachable dB reducer, allowing riders to switch between a refined touring sound and a more aggressive performance tone. This listing includes multiple finish variants under one product listing: Brushed Steel Finish Polish Finish Black Finish All variants are specifically developed for direct fitment on Royal Enfield Classic Reborn 350 and Meteor 350 motorcycles. Available Finish Variants Brushed Steel Finish Industrial-inspired satin stainless finish with strong resistance to visible scratches and heat marks. Polish Finish Mirror-like polished stainless steel appearance designed for retro premium styling enthusiasts. Black Finish Aggressive matte black styling with heat-resistant coating and stealth-inspired appearance. Key Features Compatible with Royal Enfield Classic Reborn 350 Compatible with Royal Enfield Meteor 350 Stainless steel construction Deep resonant exhaust note Detachable dB reducer included Dyno-tested setup Hand-crafted construction Improved exhaust flow efficiency Enhanced throttle response Synthetic wool acoustic insulation Optimized baffle core design OE-inspired styling and fitment Bolt-on installation Performance Benefits Better throttle response Reduced exhaust restriction Improved riding feel Deeper bass-heavy exhaust note Lightweight compared to stock exhaust Enhanced road presence Improved aesthetics Better corrosion resistance compared to stock systems Construction & Design The Powerage slip-on exhaust uses premium stainless steel internals combined with carefully tuned acoustic insulation and a precision-designed baffle core to achieve balanced performance and refined exhaust acoustics. Its slim OE-inspired body profile integrates seamlessly with the retro styling of the Classic Reborn and Meteor 350 while offering a noticeable upgrade in appearance and sound. The removable dB reducer allows riders to tune the exhaust sound according to riding preference. Package Contents 1 x Powerage Slip-On Exhaust Detachable dB Reducer Mounting Hardware Clamps & Fasteners Important Note Please select the correct finish variant before placing your order. Compatible only with Royal Enfield Classic Reborn 350 and Meteor 350. Professional installation recommended. Exhaust sound may vary depending on dB reducer installation and riding conditions.

Read more less

Upgrade the sound, styling, and riding character of your Royal Enfield Hunter 350 with the Powerage Slip-On Exhaust designed for improved exhaust flow, deeper acoustics, reduced weight, and enhanced throttle response. Crafted using premium stainless steel construction with a durable black powder-coated finish, this slip-on exhaust is engineered to provide a refined balance between everyday rideability and aggressive exhaust performance. The exhaust delivers a deep resonant exhaust note while maintaining usable back pressure through its internally engineered baffle core design. The included detachable dB reducer allows riders to adjust the sound profile according to personal preference and riding conditions. Hand-crafted and dyno-tested, the Powerage exhaust system improves overall motorcycle aesthetics while offering noticeable gains in responsiveness and riding feel. The compact OE-inspired profile ensures the exhaust integrates cleanly with the Royal Enfield Hunter 350 styling language while adding a more premium and performance-focused visual appearance. Key Features Designed specifically for Royal Enfield Hunter 350 Premium stainless steel construction Black powder-coated finish Deep resonant exhaust note Detachable dB reducer included Dyno-tested setup Hand-crafted construction Improved throttle response Lightweight slip-on design OE-inspired fit and styling Synthetic wool acoustic insulation Optimized baffle core for efficiency and back pressure Performance Benefits Improved exhaust flow Better throttle response Reduced exhaust weight Enhanced exhaust acoustics Improved low and mid-range feel Cleaner and sportier rear-end styling Better durability compared to stock mild steel systems Construction & Design The Powerage Hunter 350 exhaust features a precision-crafted stainless steel internal structure combined with a durable black powder-coated outer finish designed for heat resistance and long-term durability. Its internally optimized baffle core maintains balanced back pressure for smoother performance delivery while the synthetic wool insulation improves sound refinement and thermal resistance. The detachable dB reducer gives riders flexibility between a touring-friendly tone and a more aggressive performance exhaust note. Package Contents 1 x Powerage Slip-On Exhaust Detachable dB Reducer Mounting Hardware Clamps & Fasteners Important Note Compatible only with Royal Enfield Hunter 350. Professional installation recommended. Exhaust sound characteristics may vary depending on dB reducer installation. Intended for performance and aesthetic enhancement.

Read more less

Upgrade the exhaust flow and performance character of your Royal Enfield Himalayan 411 with the Powerage Performance Headers engineered for riders looking for stronger throttle response, improved exhaust acoustics, reduced weight, and enhanced touring performance. Manufactured from premium-grade stainless steel, these performance headers are dyno-tested and specifically developed to improve exhaust gas flow efficiency while maintaining compatibility with the stock exhaust layout and aftermarket slip-ons. The big-bore free-flow design helps unlock improved horsepower and torque delivery while giving the Himalayan a deeper and more resonant exhaust note. Built using precision hand-crafted construction, the headers maintain an OE-style routing while significantly improving overall motorcycle aesthetics and exhaust breathing capability. The integrated O2 sensor provision ensures compatibility with factory sensor setup for seamless installation. Key Features Designed specifically for Royal Enfield Himalayan 411 Big bore free-flow header design Improved horsepower and torque delivery Deeper resonant exhaust note Dyno-tested performance setup Hand-crafted stainless steel construction OE-style routing and fitment Integrated O2 sensor provision Significant weight reduction over stock setup Compatible with stock and aftermarket exhausts Improved exhaust gas flow efficiency Performance Benefits Faster throttle response Improved low and mid-range torque feel Better exhaust breathing Reduced exhaust restriction Deeper and more aggressive exhaust note Cleaner and premium visual appearance Reduced overall motorcycle weight Enhanced touring and highway ride feel Construction & Design The Powerage Performance Header uses a precision-formed big-bore stainless steel pipe layout engineered for smoother exhaust scavenging and freer exhaust flow. Its brushed steel finish delivers a clean premium appearance while offering strong corrosion resistance and long-term durability for adventure touring conditions. The system is designed to retain factory sensor compatibility while improving overall exhaust efficiency. Package Contents 1 x Powerage Performance Header Pipe Mounting Hardware Clamps & Fasteners Important Note Compatible only with Royal Enfield Himalayan 411. Professional installation recommended. Exhaust sound characteristics may vary depending on muffler setup. ECU tuning is not mandatory but may further optimize performance with aftermarket exhaust systems.

Read more less

Upgrade your Royal Enfield Shotgun 650 or Super Meteor 650 with the Powerage Slip-On Exhaust System engineered for riders who want deeper exhaust acoustics, premium stainless steel construction, improved throttle feel, and a cleaner premium finish. Manufactured using high-grade 304 Stainless Steel, the Powerage exhaust system is dyno-tested and designed to improve overall riding experience while maintaining reliability for long-distance touring and daily riding. This exhaust comes with a removable dB killer, allowing riders to switch between refined touring acoustics and a more aggressive exhaust note depending on riding preference. The system is available in multiple finish variants under the same listing: Brushed Steel Finish Polish Finish Black Finish All variants are specifically designed for direct fitment on the Royal Enfield Shotgun 650 and Super Meteor 650 without requiring major modifications. Available Finish Variants Brushed Steel Finish Premium brushed stainless appearance Classic industrial finish Scratch-resistant texture Polish Finish High-gloss premium polished appearance Bright chrome-style visual appeal Ideal for retro and touring builds Black Finish Stealth-inspired matte black styling Aggressive modern appearance Heat-resistant coated finish Key Features Compatible with Royal Enfield Shotgun 650 Compatible with Royal Enfield Super Meteor 650 Full 304 stainless steel construction Slip-on exhaust system Removable dB killer included Dyno-tested performance setup Enhanced exhaust note Improved throttle response Bolt-on direct fitment Touring-friendly performance tuning Lifetime warranty against rust & manufacturing defects Performance Benefits Deeper bass-heavy exhaust sound Improved exhaust flow efficiency Reduced back pressure Better throttle feel Enhanced road presence Cleaner premium visual styling Long-lasting corrosion resistance Technical Specifications Brand : Powerage Product Type : Slip-On Exhaust Compatibility : Royal Enfield Shotgun 650 / Super Meteor 650 Material : 304 Stainless Steel Exhaust Type : Slip-On Finish Options : Brushed Steel / Polish / Black dB Killer : Included, Removable Installation Type : Bolt-On Dyno Tested : Yes Performance Data Exhaust Weight : Approx. 6 kg Claimed Power Gain : Up to +1.9 bhp Important Note Please select the correct finish variant before placing your order. Compatible only with Royal Enfield Shotgun 650 and Super Meteor 650. Professional installation recommended. Exhaust sound may vary depending on riding conditions and tuning setup. Package Contents Pair of Powerage Slip-On Exhausts Removable dB Killers Mounting Hardware Clamps & Fasteners

Read more less