CB350 H'ness Exhaust

Control Your Exhaust. On Your Terms. Your valved exhaust has two modes — you just haven't been able to use both. The Valvetronic Exhaust Valve Control Module (Manual) gives you a handlebar-mounted switch that physically opens or closes the exhaust butterfly valve whenever you want. Full roar on the open highway. Clean and quiet through the colony, toll booth, or early morning streets. No apps. No wiring. No compromise. This is the most reliable way to control a valved exhaust — because there's nothing electronic to fail. A cable connects your thumb to the valve. That's it. What This Module Does Valved exhausts come with an internal butterfly valve that changes how exhaust gases flow. When the valve is closed, gases pass through a baffled internal route — quieter, more refined. When the valve is open, gases take the free-flow path — louder, rawer, with a more aggressive exhaust note. Most valved exhausts ship without any control module. The valve stays fixed in one position. This module gives you a switch to change it, whenever you want, from the handlebar. Closed valve: Quiet, compliant, neighbour-friendly. Use it in residential areas, at idle, in traffic, on early morning rides. Open valve: The sound your exhaust was built to make. Use it on highways, open roads, or anywhere you want the full character of your exhaust to come through. Why Manual Over Electric Zero electronics. No solenoid, no servo, no wiring loom, no relay. Nothing to short, corrode, or fail over time. Works anywhere, always. The valve opens when you pull the cable. No power required. No sensor needed. Doesn't care if your bike is warm, cold, or idling. You're in control. The valve is exactly where you put it — open or closed — until you choose to change it. No automatic switching when you don't want it. Simple to install. Route the cable, connect to the valve actuator, mount the switch. No ECU tapping, no wiring diagrams, no calibration. Built to last. A cable and a switch outlast any electronic actuator on a motorcycle. Less to maintain, less to replace. How It Works A control switch mounts on your handlebar. A cable runs from the switch down to the butterfly valve actuator on your exhaust. When you flick the switch, cable tension physically rotates the valve between open and closed. The entire system is mechanical — no power draw from your bike's electrical system, no ECU communication, no mapping required. Installation requires routing the cable cleanly along the frame to the exhaust, connecting to the existing valve actuator arm, and adjusting cable tension for full travel in both directions. A standard workshop should be able to install this in under an hour on most platforms. Compatible Bikes This is a universal module — it works with any valved exhaust system that supports mechanical cable actuation, regardless of bike brand or model. Below is a verified compatibility reference across popular Indian market platforms. If your bike has a valved slip-on, this module can control it. Royal Enfield Interceptor 650 / Continental GT 650 / Classic 650 / Bear 650 Classic 350 (Reborn) / Hunter 350 / Meteor 350 Himalayan 411 / Himalayan 450 / Guerrilla 450 Scram 411 / Super Meteor 650 / Shotgun 650 KTM Duke 125 / Duke 200 / Duke 250 / Duke 390 RC 125 / RC 200 / RC 390 Adventure 250 / Adventure 390 / Adventure 390 (2025) 790 Adventure Triumph Speed 400 / Scrambler 400 X / Tiger 400 Street Triple 675 / Speed T4 Bonneville T100 / T120 / Street Twin Tiger 800 / Street Scrambler 900 Yamaha MT-15 V2 / R15 V3 / R15 V4 FZ25 / FZS25 / Fazer 25 MT-03 / R3 YZF-R1 / YZF-R6 / MT-07 Kawasaki Ninja 400 / Ninja 650 / Ninja 1000 SX Z800 / Z900 / Z900 (2026) Versys 650 / Versys-X 300 / Versys 1000 Honda CB200X / CB350 Highness / CB350RS CBR 250R / CB300R / CB300F CBR 650R / CBR 650F / CB Hornet 160R Africa Twin / NX200 Bajaj Pulsar NS200 / RS200 / AS200 / 220F Dominar 250 / Dominar 400 NS 400Z TVS Apache RR 310 / Apache RTR 200 4V Ronin BMW G 310 R / G 310 GS / G 310 RR S 1000 R / S 1000 XR / R 1000 GS Suzuki Gixxer 250 / V-Strom 250SX / V-Strom 650 GSX-R750 / GSX-S750 / GSX-R1000 Hayabusa (2021 Onwards) Ducati Scrambler 800 / Scrambler 1100 Monster 797 / Monster 1200 Hypermotard 939 / Multistrada 950 Streetfighter V4 Harley Davidson Street 750 / Street Rod X440 / X440T Forty Eight / Iron 883 Jawa / Yezdi Jawa 42 FJ / Jawa Perak Yezdi Adventure / Yezdi Roadster Hero Karizma XMR / Xpulse 200 4V / Xpulse 210 Benelli TRK 502 / TRK 502X / TNT 600i / TNT 899 This module is universal — it controls the valve mechanism, not the exhaust itself. Your exhaust must have a butterfly valve with a mechanical actuator arm. Confirm exhaust compatibility before ordering. If your bike model isn't listed but runs a valved slip-on, this module will work. What's in the Box 1 × Valvetronic Manual Control Switch (handlebar mount) 1 × Control cable assembly Mounting hardware Exhaust system not included. Module requires a compatible valved exhaust to function. Specifications Control Type: Manual (mechanical cable) Actuation: Direct cable-pull butterfly valve operation Power Required: None ECU / Wiring Integration: Not required Valve Positions: Open / Closed (user-operated) Mount: Handlebar switch with cable routing Fitment: Universal — compatible with mechanically-actuated valved exhausts Brand: Valvetronic MRP: ₹3,499 Also Available Want automatic valve switching based on RPM and throttle input? The Valvetronic Electric (Automatic) Module does exactly that — the valve opens and closes on its own as you ride. View the Electric Module →

Read more less

Engineered for Honda CB350 Platform The Red Rooster Pegasus Max Exhaust is precision-crafted for the Honda CB350(including Special Editions). Designed to enhance both sound and ride feel, this performance exhaust delivers a balanced upgrade without compromising daily usability. Signature Deep Thump This is where the transformation happens. Deep, throaty exhaust tone Classic long-stroke character enhancement Refined—not harsh, not noisy It complements the CB350’s DNA instead of overpowering it. Performance That You Feel Up to ~10% improved throttle response Smoother acceleration delivery Better mid-range pull No artificial tuning—just optimized exhaust flow. Lightweight Advantage Noticeably lighter than stock exhaust Improves handling agility Reduces rear-end weight bias Built for Longevity Premium stainless steel construction Rust-resistant finish Designed for Indian riding conditions Plug & Play Installation Direct bolt-on fit No cutting, no welding No ECU remap required Installs on stock setup Compatibility Direct Fitment: Honda CB350 (incl. Special Editions) Variants (Finish Options) Polish – Chrome-like premium shine Black – Stealth, aggressive look Matte – Understated clean finish ⚠️ Important Notes This is a performance exhaust (slip-on) Sound output may vary based on riding conditions Check local regulations before use

Read more less

Red Rooster Pegasus Exhaust for Honda H’ness CB350 The Red Rooster Pegasus Exhaust for Honda H’ness CB350 is built for riders who want more than just a cosmetic upgrade. It is engineered to refine the character of the H’ness—adding depth to the exhaust note, improving throttle feel, and enhancing overall ride response without compromising reliability or daily usability. Constructed from Grade 304 stainless steel, the Pegasus is designed to withstand real-world riding conditions. From heat cycles in city traffic to long highway stretches under load, the material resists corrosion, discoloration, and structural fatigue. The stainless construction also allows better thermal stability, which plays a key role in maintaining consistent exhaust tone and performance over time. This is not a thin decorative canister—it is a properly engineered performance component tuned specifically for the CB350 platform. Internally, the Pegasus uses ceramic-wool insulation to regulate heat dispersion and stabilize sound output. This insulation layer helps maintain exhaust gas velocity while preventing excessive resonance or harshness. The result is a rich, throaty tone that feels mature and mechanical rather than loud for the sake of volume. It complements the long-stroke character of the H’ness engine, adding depth without overwhelming refinement. Throttle response becomes noticeably sharper. Mid-range torque delivery feels cleaner and more linear, particularly during overtakes or rolling acceleration in higher gears. The Pegasus improves exhaust flow efficiency, helping the engine breathe more freely while maintaining usable rideability across the rev range. Instead of chasing peak numbers, the system focuses on real-world ride feel—smoother roll-on response, steadier cruising tone, and improved consistency during long rides. Weight reduction over the stock exhaust contributes to a more responsive handling experience. The CB350 retains its stability, but gains a slightly livelier character during corner entry and low-speed maneuvering. For riders who commute daily and tour occasionally, this translates into less fatigue and more confidence in mixed riding environments. Fitment is designed as a true bolt-on system. There is no requirement for fuel remapping, ECU changes, wiring modifications, or fabrication. The Pegasus mounts directly using factory attachment points, ensuring correct alignment and structural integrity. Installation remains straightforward while preserving the original mounting geometry of the bike. The Pegasus is available in Polish and Black finishes, each offering a distinct aesthetic appeal: Polished Finish provides a clean metallic look that highlights the stainless-steel construction. It pairs well with chrome accents and classic styling cues of the H’ness CB350. Black Finish offers a more understated, stealth-oriented appearance with a heat-resistant coating that maintains durability under prolonged use. Both finishes are engineered for longevity, resisting rust, surface degradation, and discoloration from heat exposure. The visual upgrade complements the motorcycle’s retro-modern styling without overpowering its identity. Sound tuning remains one of the strongest characteristics of the Pegasus. At idle, it produces a controlled, bass-heavy pulse that enhances presence without excessive sharpness. Under acceleration, the note deepens progressively, maintaining tonal clarity rather than turning hollow or metallic. On highways, the sound settles into a stable frequency band that minimizes fatigue during extended cruising. For riders who value mechanical authenticity over unnecessary noise, the Pegasus strikes a balanced tone. It enhances the CB350’s voice without distorting its personality. Durability remains central to the design philosophy. Every weld, bend, and contour is manufactured to endure vibration, thermal expansion, and extended usage. The system is built not only for aesthetic improvement, but for long-term ownership confidence. Whether used for urban commuting, weekend highway runs, or occasional touring, the Pegasus integrates seamlessly into the riding experience. It improves response, refines tone, and reinforces durability—all while preserving the reliability of the Honda H’ness CB350 platform. This is not a decorative accessory. It is a structured performance enhancement engineered for riders who appreciate balance—sound without harshness, performance without compromise, and styling without excess.

Read more less