Royal Enfield Bear 650

Control Your Exhaust. On Your Terms. Your valved exhaust has two modes — you just haven't been able to use both. The Valvetronic Exhaust Valve Control Module (Manual) gives you a handlebar-mounted switch that physically opens or closes the exhaust butterfly valve whenever you want. Full roar on the open highway. Clean and quiet through the colony, toll booth, or early morning streets. No apps. No wiring. No compromise. This is the most reliable way to control a valved exhaust — because there's nothing electronic to fail. A cable connects your thumb to the valve. That's it. What This Module Does Valved exhausts come with an internal butterfly valve that changes how exhaust gases flow. When the valve is closed, gases pass through a baffled internal route — quieter, more refined. When the valve is open, gases take the free-flow path — louder, rawer, with a more aggressive exhaust note. Most valved exhausts ship without any control module. The valve stays fixed in one position. This module gives you a switch to change it, whenever you want, from the handlebar. Closed valve: Quiet, compliant, neighbour-friendly. Use it in residential areas, at idle, in traffic, on early morning rides. Open valve: The sound your exhaust was built to make. Use it on highways, open roads, or anywhere you want the full character of your exhaust to come through. Why Manual Over Electric Zero electronics. No solenoid, no servo, no wiring loom, no relay. Nothing to short, corrode, or fail over time. Works anywhere, always. The valve opens when you pull the cable. No power required. No sensor needed. Doesn't care if your bike is warm, cold, or idling. You're in control. The valve is exactly where you put it — open or closed — until you choose to change it. No automatic switching when you don't want it. Simple to install. Route the cable, connect to the valve actuator, mount the switch. No ECU tapping, no wiring diagrams, no calibration. Built to last. A cable and a switch outlast any electronic actuator on a motorcycle. Less to maintain, less to replace. How It Works A control switch mounts on your handlebar. A cable runs from the switch down to the butterfly valve actuator on your exhaust. When you flick the switch, cable tension physically rotates the valve between open and closed. The entire system is mechanical — no power draw from your bike's electrical system, no ECU communication, no mapping required. Installation requires routing the cable cleanly along the frame to the exhaust, connecting to the existing valve actuator arm, and adjusting cable tension for full travel in both directions. A standard workshop should be able to install this in under an hour on most platforms. Compatible Bikes This is a universal module — it works with any valved exhaust system that supports mechanical cable actuation, regardless of bike brand or model. Below is a verified compatibility reference across popular Indian market platforms. If your bike has a valved slip-on, this module can control it. Royal Enfield Interceptor 650 / Continental GT 650 / Classic 650 / Bear 650 Classic 350 (Reborn) / Hunter 350 / Meteor 350 Himalayan 411 / Himalayan 450 / Guerrilla 450 Scram 411 / Super Meteor 650 / Shotgun 650 KTM Duke 125 / Duke 200 / Duke 250 / Duke 390 RC 125 / RC 200 / RC 390 Adventure 250 / Adventure 390 / Adventure 390 (2025) 790 Adventure Triumph Speed 400 / Scrambler 400 X / Tiger 400 Street Triple 675 / Speed T4 Bonneville T100 / T120 / Street Twin Tiger 800 / Street Scrambler 900 Yamaha MT-15 V2 / R15 V3 / R15 V4 FZ25 / FZS25 / Fazer 25 MT-03 / R3 YZF-R1 / YZF-R6 / MT-07 Kawasaki Ninja 400 / Ninja 650 / Ninja 1000 SX Z800 / Z900 / Z900 (2026) Versys 650 / Versys-X 300 / Versys 1000 Honda CB200X / CB350 Highness / CB350RS CBR 250R / CB300R / CB300F CBR 650R / CBR 650F / CB Hornet 160R Africa Twin / NX200 Bajaj Pulsar NS200 / RS200 / AS200 / 220F Dominar 250 / Dominar 400 NS 400Z TVS Apache RR 310 / Apache RTR 200 4V Ronin BMW G 310 R / G 310 GS / G 310 RR S 1000 R / S 1000 XR / R 1000 GS Suzuki Gixxer 250 / V-Strom 250SX / V-Strom 650 GSX-R750 / GSX-S750 / GSX-R1000 Hayabusa (2021 Onwards) Ducati Scrambler 800 / Scrambler 1100 Monster 797 / Monster 1200 Hypermotard 939 / Multistrada 950 Streetfighter V4 Harley Davidson Street 750 / Street Rod X440 / X440T Forty Eight / Iron 883 Jawa / Yezdi Jawa 42 FJ / Jawa Perak Yezdi Adventure / Yezdi Roadster Hero Karizma XMR / Xpulse 200 4V / Xpulse 210 Benelli TRK 502 / TRK 502X / TNT 600i / TNT 899 This module is universal — it controls the valve mechanism, not the exhaust itself. Your exhaust must have a butterfly valve with a mechanical actuator arm. Confirm exhaust compatibility before ordering. If your bike model isn't listed but runs a valved slip-on, this module will work. What's in the Box 1 × Valvetronic Manual Control Switch (handlebar mount) 1 × Control cable assembly Mounting hardware Exhaust system not included. Module requires a compatible valved exhaust to function. Specifications Control Type: Manual (mechanical cable) Actuation: Direct cable-pull butterfly valve operation Power Required: None ECU / Wiring Integration: Not required Valve Positions: Open / Closed (user-operated) Mount: Handlebar switch with cable routing Fitment: Universal — compatible with mechanically-actuated valved exhausts Brand: Valvetronic MRP: ₹3,499 Also Available Want automatic valve switching based on RPM and throttle input? The Valvetronic Electric (Automatic) Module does exactly that — the valve opens and closes on its own as you ride. View the Electric Module →

Read more less

NGage B8RII-8 Double Iridium Spark Plug for Royal Enfield Himalayan & 650 Series (BS4 & BS6) The NGage B8RII-8 Double Iridium Spark Plug is a premium motorcycle spark plug developed for select Royal Enfield motorcycles, including the Himalayan and the full 650 platform range listed below. Manufactured in Japan, this spark plug is part of NGage’s iridium series designed for modern motorcycle ignition systems used in both BS4 and BS6 applications. NGage specifies the B8RII-8 as a Double Iridium spark plug, indicating the use of iridium material on both the center electrode and the ground electrode. Iridium is chosen in spark plug manufacturing for its ability to withstand high combustion temperatures while maintaining electrode stability over time. This construction approach is commonly used in modern motorcycles that operate under tighter emission and combustion control requirements. Application for Royal Enfield Motorcycles The B8RII-8 spark plug is listed by NGage for use in multiple Royal Enfield motorcycles across two distinct engine platforms: The Royal Enfield Himalayan The Royal Enfield 650 series, including Interceptor 650, Continental GT 650, Bear 650, Super Meteor 650, Shotgun 650, and Classic 650 These motorcycles share ignition system requirements that align with the B8RII-8 specification as published by NGage. This spark plug is intended as a direct replacement within these applications, without modification. The Royal Enfield 650 platform spans multiple body styles and riding formats, but ignition requirements remain consistent across these models. Listing each model explicitly ensures clarity for riders searching by motorcycle name rather than engine family or platform grouping. Compatibility with BS4 and BS6 Vehicles NGage specifies that the B8RII-8 spark plug is compatible with both BS4 and BS6 vehicles. This makes it suitable for Royal Enfield motorcycles produced before and after the transition to BS6 emission standards, provided the motorcycle is included in the compatibility list. No additional emission-related claims, tuning effects, or regulatory certifications are stated by NGage for this product, and none are implied here. Manufacturing Origin The NGage B8RII-8 spark plug is manufactured in Japan, as stated on the product packaging. NGage does not publish further details regarding production processes, quality certifications, or testing standards for this model. The country of manufacture is provided as factual information only. Intended Use This spark plug is designed for routine replacement during scheduled maintenance or when replacing worn ignition components on compatible Royal Enfield motorcycles. It is suitable for standard road use within manufacturer-recommended service intervals. NGage does not classify this spark plug as a racing-only, track-specific, or performance-tuning component. It is intended for regular motorcycle operation within the scope of the listed applications. Fitment Accuracy Correct spark plug selection is critical for engine operation. The B8RII-8 should be installed only on motorcycles listed in the compatibility section below. Use on non-listed models is not recommended. Royal Enfield Himalayan 450 is not compatible with this spark plug. The Himalayan 450 uses a different engine architecture and ignition specification. Compatibility Royal Enfield Motorcycles Royal Enfield Himalayan Royal Enfield Interceptor 650 Royal Enfield Continental GT 650 Royal Enfield Bear 650 Royal Enfield Super Meteor 650 Royal Enfield Shotgun 650 Royal Enfield Classic 650 Variant Explanation This listing covers NGage B8RII-8 Double Iridium Spark Plug only. “Double Iridium” refers to iridium usage on both electrodes, as defined by NGage. No alternative heat ranges or material variants are included under this listing. Any comparison with other spark plug constructions is outside the scope of this product page. Specifications Brand: NGage Part Number: B8RII-8 Spark Plug Type: Double Iridium Vehicle Compatibility: BS4 & BS6 Country of Manufacture: Japan Application: Motorcycle spark plug Installation / Usage Notes Install on compatible motorcycles only. Follow Royal Enfield service manual torque specifications. Ensure the engine is cool before installation. NGage does not publish gap or torque values for this spark plug.

Read more less

Built for the Bear 650 Twin Engine The Barrel B-20 Bass Master Exhaust is engineered specifically for the Royal Enfield Bear 650 platform. This is not just a slip-on—it’s a performance-focused system with a decat pipe designed to unlock the full breathing potential of the 650 twin engine. 🔊 Signature Bass Master Sound Deep, bass-heavy exhaust tone Strong low-frequency thump No sharp or raspy noise This is tuned for authority, not noise pollution. ⚙️ Decat Performance Advantage Unlike standard slip-ons, this setup includes a decat pipe: Frees up exhaust flow Reduces back pressure Improves engine breathing Enhances throttle response Result → smoother, more responsive acceleration ⚡ Performance Gains You Can Feel Noticeably sharper throttle response Improved torque delivery More engaging riding experience No unnecessary tuning complexity—just real-world gains. 🪶 Weight Reduction & Build Quality Saves approx 1.5–5.5 kg vs stock Constructed from 304 Stainless Steel High durability + corrosion resistance 🛠️ Plug & Play Fitment Direct bolt-on installation (OEM mounts) No cutting or welding required Installation time: ~30–45 minutes 🔧 DB Killer Control Comes with removable DB killer Tune sound based on preference: With DB killer → controlled Without → full bass roar 📦 What’s in the Box B-20 Bass Master Exhaust Decat Pipe DB Killer Mounting Hardware ✅ Compatibility Royal Enfield Bear 650 ⚠️ Important Notes This is a performance exhaust with decat pipe May not comply with emission or noise regulations in all regions ECU remap is not mandatory, but can help extract optimal performance Sound output will be significantly louder than stock 🛡️ Warranty Manufacturer Warranty: Lifetime rust warranty 1-year weld warranty RawTorque Note:RawTorque does not provide any additional warranty beyond the manufacturer’s coverage.For more details, please refer to our warranty policy.

Read more less

Moto Torque Stage II Air Filter Combo Kit for Interceptor 650, Continental GT 650 & Bear 650 The Moto Torque Air Filter Stage II Combo Kit is designed exclusively for Royal Enfield Interceptor 650, Continental GT 650, and Bear 650 motorcycles. This combo package integrates the Moto Torque Performance Air Filter with the Stage II upgrade kit to deliver enhanced airflow, sharper throttle response, and smoother acceleration. Engineered specifically for the Royal Enfield 650 twin-cylinder platform, this kit is built to improve intake efficiency while maintaining durability and precision fitment. Designed for Royal Enfield 650 Twin Platform • Royal Enfield Interceptor 650• Royal Enfield Continental GT 650• Royal Enfield Bear 650• Precision engineered for RE 650 twin-cylinder engines Model-specific compatibility ensures correct alignment and plug-and-play installation. Complete Performance Package • Includes Performance Air Filter• Includes Stage II upgrade kit• Integrated high-flow intake solution This bundled system is structured to optimize airflow while supporting consistent engine performance. Engineered Features Stainless Steel ConstructionCorrosion-resistant structure built for long-term durability. Enhanced AirflowImproved intake efficiency supports stronger and smoother power delivery. Precision FitDesigned specifically for Royal Enfield 650 twins and Bear 650 platform. Easy InstallationPlug-and-play design for straightforward installation. Performance Benefits • Sharper throttle response• Smoother acceleration• Optimized airflow delivery• Long-lasting structural durability Designed to complement the performance characteristics of the 650cc twin engine. Specifications • Brand: Moto Torque• Product Type: Stage II Air Filter Combo Kit• Compatibility: Interceptor 650 / Continental GT 650 / Bear 650• Construction: Stainless Steel + High-flow Filter• Installation: Plug-and-Play

Read more less

N-Gage Hyper Flow Air Filter for Royal Enfield 650 Twins (Interceptor 650 / Continental GT 650) The N-Gage Hyper Flow Royal Enfield air filter for Royal Enfield 650 Twins is a performance replacement designed exclusively for Royal Enfield motorcycles powered by the 650cc parallel-twin engine. This includes popular models like the Interceptor 650, Continental GT 650, and other 650-platform variants with similar intake architecture. This Royal Enfield air filter ensures optimized airflow while maintaining excellent filtration to protect your engine. Proper filtration of air is crucial for engine efficiency, throttle response, and long-term durability. On large twin-cylinder engines, uneven airflow or restrictive filters can cause inconsistent engine performance, especially during acceleration and steady riding. The N-Gage Hyper Flow Air Filter delivers improved intake breathing and safeguards the engine from dust, debris, and contaminants commonly found on Indian roads. High-Flow Cotton Gauze Construction with Royal Enfield air filter Benefits This air filter uses premium organic cotton gauze that is layered to achieve a balance between airflow and filtration efficiency. Cotton gauze filters are preferred in performance settings because they allow a greater volume of air compared to traditional disposable paper filters when maintained correctly. The N-Gage filter comes factory pre-oiled to capture fine dust while enabling higher airflow through the intake. This design supports consistent and reliable air delivery whether you are commuting in the city, cruising on highways, or touring long distances. Specifically Designed for Royal Enfield 650 Twin Engines The N-Gage Hyper Flow Air Filter is custom-built for the Royal Enfield 650 twin-cylinder platform. It fits perfectly in the stock airbox of these motorcycles, allowing installation as a direct replacement without cutting, drilling, or other modifications. The filter matches the motorcycle’s original mounting points and dimensions, ensuring seamless integration with the intake system. This retention preserves the sealing surfaces and weather protection originally provided after installation. Enhanced Throttle Response and Ride Feel By improving airflow, this Royal Enfield air filter can lead to a noticeably smoother throttle response and more predictable engine behavior. Riders often upgrade to high-flow filters to reduce intake restriction, particularly on engines designed for strong mid-range and highway performance. The manufacturer confirms that this filter works with the stock ECU and exhaust system, so no remapping or tuning is required in most cases. However, actual ride feel may vary depending on factors such as fuel quality, rider style, and engine condition. Washable and Reusable Design for Longevity This air filter offers a washable and reusable solution, unlike disposable paper filters that require frequent replacement. With proper cleaning and re-oiling using suitable maintenance products, the filter can be reused multiple times over its lifespan, making it an economical choice. Long-term owners looking to minimize consumable replacement costs will appreciate this design. Proper maintenance helps maintain filtration efficiency and continual engine protection with this Royal Enfield air filter. Built for Indian Riding Conditions Royal Enfield 650 motorcycles face a variety of riding environments, including congested city traffic, highway cruising, and dusty touring routes. The N-Gage Hyper Flow Air Filter is engineered to maintain consistent airflow and filtration across these conditions. Riders in dusty or challenging environments should adjust their cleaning schedule accordingly to maintain optimal filter performance and engine health. Installation and Maintenance Guidelines Installing the N-Gage Hyper Flow Air Filter follows the same steps as replacing the stock air filter. No special tools are required. Motorcyclists should ensure the filter sits correctly within the airbox and sealing surfaces are clean during installation. For best results, cleaning and re-oiling should be done periodically with recommended products. Over-oiling or improper care can reduce filtration efficiency and risk engine damage. Compatibility and What’s Included This Royal Enfield air filter fits motorcycles powered by the 650cc twin-cylinder platform, including: Royal Enfield Interceptor 650 Royal Enfield Continental GT 650 Fitment is based on stock intake configurations to ensure straightforward installation. The package includes one N-Gage Hyper Flow Air Filter, factory pre-oiled and ready for immediate use.

Read more less

FuelX Pro+ Advanced Smart Autotune Module for Royal Enfield | 10 Dynamic Maps | Handlebar Switch | Plug & Play Maximize your Royal Enfield’s performance with precision.The FuelX Pro+ Advanced Smart Autotune Module is a plug-and-play fueling solution engineered specifically for Royal Enfield motorcycles. It is designed for riders who want smoother throttle response, refined power delivery, and real-time fueling optimization — without flashing the ECU or visiting a dyno. Unlike static fuel controllers, FuelX Pro+ continuously reads engine data and automatically adjusts the air-fuel ratio while you ride. The result is cleaner acceleration, reduced jerks at low RPM, and improved ride smoothness across city traffic, highways, and mountain roads. Advanced Autotune Control – 10 Dynamic Maps FuelX Pro+ features 10 Dynamic Autotune Maps, allowing riders to select their preferred fueling character. Each map offers a different response profile, ranging from smooth touring behavior to sharper throttle engagement. The included Handlebar Map Switch lets you change maps on the go. No laptop. No external device. No workshop visit. Simply select your map and feel the difference instantly. This flexibility makes FuelX Pro+ suitable for riders who commute daily, tour long distances, or ride aggressively on open highways. Real-Time Adaptive Fueling Technology At the core of the FuelX Pro+ system is its Auto Adapt technology. The module continuously analyzes engine operating parameters and automatically adjusts fueling in real time. This helps compensate for: • Altitude variations• Temperature changes• Aftermarket exhaust upgrades• Free-flow air filters• Riding load differences Instead of running too lean or inconsistent, your motorcycle maintains a stable and optimized air-fuel ratio. This results in smoother engine behavior, cooler running temperatures, and improved throttle refinement. Improved Ride Feel & Throttle Response FuelX Pro+ is engineered to enhance everyday ride quality. Riders typically experience: • Sharper throttle precision• Reduced engine hesitation• Smoother low-RPM tractability• Cleaner roll-on acceleration The manufacturer states up to 25% improved throttle precision and significantly enhanced acceleration response. These gains focus on real-world rideability rather than peak dyno numbers. This module is not marketed as a race ECU replacement. It is a smart adaptive fueling system built for usable performance. Plug-and-Play Installation Installation is fully non-intrusive and reversible. The module connects directly to the stock wiring harness using OEM-style connectors. There is no wire cutting, no ECU rewriting, and no permanent modification required. Install the unit, mount the switch, select your map, and ride. Professional installation is recommended if you are unfamiliar with motorcycle electrical systems, but experienced riders can complete installation with standard tools. Durable Automotive-Grade Construction FuelX Pro+ is built using automotive-grade electronic components. The compact control unit is weather-resistant, vibration-resistant, and heat-resistant. The harness features protective braided sleeving, ensuring durability under long touring conditions and harsh weather exposure. Designed for real riding conditions — not just showroom specs. Compatibility – Royal Enfield Motorcycles FuelX Pro+ is compatible with a wide range of Royal Enfield motorcycles. Fitment varies by model and generation. Common compatible platforms include: • Himalayan 450 • Guerrilla 450• Classic 350 /500• Meteor 350 / Hunter 350 / Bullet 350• Interceptor 650• Continental GT 650• Bear 650• Super Meteor 650• Himalayan 411  Always select your exact motorcycle model and year before purchase to ensure proper fitment. Who Is This For? FuelX Pro+ is ideal for riders who: • Want smoother throttle control• Have installed a free-flow exhaust or air filter• Ride in varying altitudes• Experience lean fueling hesitation• Prefer adaptive performance without ECU flashing It is not a racing ECU or ignition timing modifier. It is an intelligent fueling optimizer built for street and touring motorcycles. What’s Included • FuelX Pro+ Smart Autotune Module• Handlebar Map Switch• Model-specific plug-and-play harness• Manufacturer documentation Only components listed above are included. Specifications Brand: FuelXModel: Pro+Type: Advanced Smart Autotune ModuleMaps: 10 Dynamic Autotune MapsSwitch: Handlebar Map Switch IncludedInstallation: Plug-and-PlayConstruction: Weather & Heat ResistantWarranty: 2-Year Manufacturer Warranty

Read more less

FuelX Lite Smart Autotune Module for Royal Enfield | Plug & Play Ride Refinement | Real-Time AFR Optimization Ride Smarter. Feel the Tune. The FuelX Lite Smart Autotune Module for Royal Enfield motorcycles is engineered for riders who want smoother throttle response, refined ride quality, and optimized engine performance — without ECU remapping or complex tuning tools. This is a true plug-and-play fuel optimizer designed to enhance everyday rideability while preserving factory reliability. Unlike traditional piggyback ECUs that require map selection or manual adjustments, the FuelX Lite continuously monitors and corrects the air–fuel ratio in real time. The result is improved combustion efficiency, reduced engine jerks, and noticeably smoother acceleration across city traffic, highway cruising, and changing riding conditions. What FuelX Lite Actually Does Modern Royal Enfield motorcycles are tuned lean from the factory to meet emission norms. A lean air–fuel mixture can sometimes cause abrupt throttle response, engine heat buildup, or minor hesitation during low-RPM riding. The FuelX Lite Smart Autotune Module automatically adjusts fueling within safe operating limits. It enriches the mixture where necessary and stabilizes it across RPM ranges. This leads to: Smoother throttle pickup Reduced on–off jerks in traffic Cooler engine operation More consistent power delivery There are no selectable maps, no handlebar switches, and no manual intervention required. The module self-calibrates based on riding style and environmental conditions. Real-World Riding Benefits The difference is most noticeable in stop-and-go traffic and low-speed maneuvering. Riders often experience smoother roll-on acceleration and improved clutch-throttle coordination. On highways, the bike feels more composed and refined during steady cruising. FuelX Lite also compensates for altitude changes and temperature variations, maintaining optimal air–fuel balance whether you’re riding in coastal humidity or mountain terrain. This is not a race tuning device. It is a ride refinement module built for daily usability. Engine Temperature & Efficiency By optimizing fueling, the FuelX Lite Smart Autotune Module helps stabilize combustion temperatures. Improved mixture balance can contribute to smoother engine operation and reduced heat stress during prolonged riding. The module works within the motorcycle’s stock ECU parameters. It does not override safety protocols or require permanent changes to the wiring harness. Plug & Play Installation Installation is simple and fully reversible. No ECU flash required No dyno tuning needed No wire cutting No permanent modification The unit connects inline with factory connectors and installs in minutes. It integrates seamlessly with the stock system and can be removed without leaving any trace. The compact, sealed construction ensures durability in heat, vibration, dust, and rain conditions typical of Indian riding environments. Build Quality & Durability The FuelX Lite module is manufactured using automotive-grade components, ensuring long-term reliability. The wiring harness features high-quality connectors designed for vibration resistance and weather protection. The module housing is sealed to withstand: Heat from the engine bay Exposure to rain and humidity Regular road vibration Daily commuting stress This is a durable electronics unit engineered for real-world use, not a fragile aftermarket gadget. Compatibility The FuelX Lite Smart Autotune Module for Royal Enfield motorcycles is available for multiple models, including: Royal Enfield Himalayan 450 Royal Enfield Guerrilla 450 Royal Enfield Classic 350 Royal Enfield Hunter 350 Royal Enfield Meteor 350 Other compatible Royal Enfield variants (select model before purchase) Always choose your exact motorcycle model and year from the product options to confirm correct fitment. Who Is This For? FuelX Lite is ideal for riders who: Want smoother throttle without aggressive tuning Prefer improved ride refinement over peak power claims Ride daily in traffic conditions Tour long distances Want plug-and-play simplicity If you are looking for multi-map customization, advanced switching, or aggressive tuning adjustments, FuelX Pro is the appropriate upgrade. FuelX Lite focuses strictly on automatic refinement. Warranty & Authenticity This product is covered under the official manufacturer warranty as per FuelX brand terms. RawTorque supplies only 100% genuine FuelX Smart Autotune Modules, sourced through authorized distribution channels. RawTorque does not provide independent warranties beyond the manufacturer’s coverage. Please refer to our official Warranty Policy for full details.

Read more less

Precision Ignition Upgrade for 650 Twins The NGage High Performance Spark Plug Kit is engineered to enhance ignition efficiency across Royal Enfield 650 twin-cylinder engines. This is not just a replacement—it’s a complete ignition system upgrade designed for smoother, cleaner, and more responsive performance. ⚡ Improved Combustion Efficiency With NGK Iridium IX spark plugs and ultra low-resistance racing cables, the system ensures: Better spark consistency Cleaner combustion Reduced misfires 🧠 Smoother, More Responsive Engine Optimized ignition delivery results in: Improved throttle response Better acceleration feel More stable idle 🌧️ Reliable in All Conditions Designed to perform across varying environments: Easier cold starts Reliable ignition in wet weather Consistent performance in daily riding 🏁 Built for Street & Performance Use Compatible with stock and modified setups Works across touring, daily riding, and spirited use Suitable for BS4 & BS6 motorcycles 📦 WHAT’S INCLUDED NGK Iridium IX Spark Plugs (CR8EIX) – 2 Nos NGage Resistor Spark Caps (XD05F-R, 5kΩ) – 2 Nos NGage Racing Spark Plug Cables (Ultra Low Resistance) – 2 Nos

Read more less

NGage B8RII-8 Double Iridium Spark Plug — Universal Fitment The NGage B8RII-8 is a Double Iridium spark plug made in Japan, compatible with BS-4 and BS-6 vehicles. It fits a wide range of mid-to-large displacement motorcycles across Royal Enfield, Triumph, Kawasaki, Yamaha, Bajaj, Benelli, Harley-Davidson, Suzuki, TVS, Aprilia, Jawa, Yezdi, and Hero platforms. If your service manual or mechanic specifies B8RII-8 as the correct plug code, this is the exact component. Technical Specifications Part Number B8RII-8 Brand NGage Powerparts Series Double Iridium Origin Made in Japan Thread Diameter 14 mm Heat Range 8 Electrode Type Double iridium (iridium centre + iridium ground) BS Compliance BS-4 and BS-6 compatible Supplied As Single plug Why Double Iridium Unlike standard iridium plugs that use iridium only on the centre electrode, the B8RII-8 uses iridium on both the centre and ground electrodes. This means: Spark erosion is distributed across both electrodes — significantly longer service life Consistent spark energy throughout the plug's lifespan, not just when new More reliable cold starts and stable combustion at all RPM ranges Suitable for high-displacement engines with higher ignition demand Full Compatibility Reference fitment guidance available per NGage compatibility data. Always cross-reference against your owner's manual or service documentation before purchase. Royal Enfield Himalayan 411 Himalayan 440 Interceptor 650 Continental GT 650 Bear 650 Super Meteor 650 Shotgun 650 Classic 650 Triumph Tiger 1050 Tiger 1050 Sport Sprint GT Speed Triple Speed Triple 1050 Speed Triple R Tiger 1200 Explorer Tiger 1200 XC Tiger 1200 XR Tiger Trophy Kawasaki Ninja 300 Ninja 250R Ninja Z250 Z900 Yamaha YZF R15 (V1, V2, V3 & V4) MT-15 YZF R3 MT-03 Aerox V2 / NVX 155 Bajaj Pulsar 200NS Triple Spark (Side Plugs × 2) Pulsar NS200 Triple Spark (Side Plugs × 2) Pulsar RS200 Triple Spark (Side Plugs × 2) Benelli 502 C TRK 502 TRK 502 X Leoncino 500 Harley-Davidson Street 750 Street Rod 750 Suzuki Suzuki 125 Burgman Suzuki V-Strom 250 TVS Motor Company Apache RTR 160 Apache RTR 180 ABS Aprilia SR 125 SR 150 Jawa Forty Two Bobber 42 350 42 FJ Yezdi Roadster Adventure Scrambler Hero MotoCorp Xpulse 200 2V / 200T Compatibility is specification-based per NGage fitment data. Verify against your service manual before ordering. Bajaj Pulsar NS200, RS200, and 200NS Triple Spark models require 2 units (side plug positions). Installation Notes Verify pre-set gap against your manufacturer's specification before installation Tighten to the torque value specified in your service manual Clean threads before installation; do not over-torque Bajaj Pulsar NS200 / RS200 / 200NS Triple Spark side plug positions require 2 units per bike In The Box 1 × NGage B8RII-8 Double Iridium Spark Plug

Read more less

Upgrade your Royal Enfield Bear 650 with the Powerage Slip-On Exhaust System featuring a performance-focused de-cat pipe setup engineered for improved exhaust flow, reduced weight, deeper exhaust note, and enhanced throttle response. Manufactured entirely from premium 304 Stainless Steel, the Powerage exhaust system is dyno-tested and designed to deliver a balance of usable performance and refined sound without compromising daily rideability. This exhaust setup is available in two muffler variants: OE Type – Factory-inspired premium styling Cone Type – Sportier tapered exhaust profile Both variants include the de-cat pipe and removable dB killer, giving riders the flexibility to tune the exhaust note according to riding preference. The system significantly reduces overall exhaust weight compared to the stock setup while improving engine breathing efficiency and delivering a richer, deeper exhaust tone. Available Variants OE Type OEM-inspired exhaust styling Cleaner factory-style appearance Ideal for subtle premium builds Cone Type Sportier aggressive exhaust design Sleeker tapered muffler profile Ideal for performance-inspired builds Key Features Designed specifically for Royal Enfield Bear 650 Full 304 stainless steel construction Includes performance de-cat pipe Dyno-tested configuration Removable dB killer included Improved exhaust flow efficiency Deeper bass-heavy exhaust note Weight reduction over stock exhaust Bolt-on fitment No ECU remap mandatory for installation Lifetime warranty against rust & manufacturing defects Performance Benefits Sharper throttle response Reduced overall exhaust weight Improved engine breathing Enhanced exhaust sound character Better heat resistance compared to mild steel systems Freer exhaust flow for smoother power delivery Technical Specifications Brand : Powerage Product Type : Slip-On Exhaust System Compatibility : Royal Enfield Bear 650 Material : 304 Stainless Steel Exhaust Type : Slip-On with De-Cat Pipe Muffler Variants : OE Type / Cone Type dB Killer : Included, Removable Finish : Stainless Steel / Matte Black depending on variant Installation Type : Bolt-On Dyno Tested : Yes Weight Information Slip-On Weight : 2.5 kg De-Cat Pipe Weight : 0.7 kg Stock OE Exhaust Weight : Approx. 6.5 kg Claimed Power Gain : Up to +2.5 bhp Important Note Please select the correct exhaust variant before placing your order. This listing is compatible only with Royal Enfield Bear 650. Professional installation is recommended for best fitment and alignment. Exhaust sound may vary depending on tuning and riding conditions. Package Contents 1 x Powerage Slip-On Exhaust 1 x De-Cat Pipe Mounting Hardware Clamps & Fasteners Removable dB Killer

Read more less

Performance Braking Upgrade for Bear 650 The 66BHP Race Pro Sintered Brake Pads are built for the Royal Enfield Bear 650, delivering stronger stopping power, sharper response, and consistent braking under demanding riding conditions. Designed for riders who push beyond standard limits, these pads focus on braking confidence when speed, load, and riding intensity increase. Sintered Compound Setup The Race Pro pads use a sintered compound tuned for higher braking demands: Aggressive initial bite for stronger braking response Designed for performance-oriented riding Consistent braking feel under load This setup provides a noticeable step up from basic replacement pads. High Heat Resistance Built to handle repeated braking stress: Maintains performance under high temperatures Handles sustained braking pressure Suitable for highway and spirited riding Fade-Resistant Performance Engineered for consistency during demanding use: Reduced brake fade during prolonged braking Reliable stopping performance on long rides and descents Maintains control under repeated braking cycles Wet and Variable Condition Confidence Adapted for real-world riding environments: Stable braking response in wet conditions Predictable feel on changing road surfaces Improved rider confidence in unpredictable scenarios Built for Performance-Focused Riding Race Pro is designed for riders seeking stronger braking authority: Better control during aggressive riding More confidence at higher speeds Suitable for highway, touring, and spirited riding

Read more less

Precision-Tuned Performance Suspension for Bear 650 The 66BHP Air Born Series Shock Absorber is engineered specifically for the Royal Enfield Bear 650, delivering a fully adjustable rear suspension setup designed for controlled handling and improved ride dynamics. Built by the 66BHP Performance Division, this suspension system integrates multiple adjustment parameters to fine-tune ride characteristics across varying road conditions and riding styles. Multi-Point Adjustability The Air Born Series offers independent tuning controls, allowing riders to dial in suspension behavior with precision: Rebound adjustment for controlled shock return Compression adjustment to manage damping response Spring preload adjustment to suit rider weight and load This setup enables better stability under braking, improved cornering confidence, and optimized comfort across different terrains. Progressive Spring Configuration Equipped with a progressive rate spring, the shock adapts to varying loads and impacts: Softer response over minor bumps Increased resistance under heavy compression This ensures balanced ride quality without compromising on support during aggressive riding or carrying additional load. Built for Real-World Riding Designed for road conditions where surface variability is common, the Air Born suspension enhances: Mid-weight touring comfort Load-carrying capability Daily riding usability

Read more less

Legundary Vambrace Bash Plate for Royal Enfield Bear 650 – Mild Steel Engine Underbody Protection The Legundary Vambrace Bash Plate is a model-specific underbody protection component designed for the Royal Enfield Bear 650. Built from mild steel with a black powder-coated finish, this bash plate creates a protective layer beneath the engine and lower frame — guarding against rocks, trail debris, and rough road impact that would otherwise reach exposed mechanical components. The Bear 650 is an adventure-capable platform built for mixed terrain. Its engine sump, lower frame rails, and exhaust routing sit exposed to ground-level impact. Even moderate off-road riding introduces rocks, ruts, and obstacles that can dent oil sumps or crack exhaust headers. The Vambrace Bash Plate eliminates direct exposure through structured underbody coverage. This is operational protection — not styling. Mild Steel Construction Constructed from mild steel, the Vambrace Bash Plate is built to absorb and deflect rock strike impact from below, protect the engine sump from cracking or denting, shield lower frame rails from gravel and debris damage, and withstand sustained vibration in off-road environments. The black powder-coated finish adds corrosion resistance and integrates visually with the Bear 650's underbody architecture. Designed for Royal Enfield Bear 650 The Vambrace Bash Plate is engineered for direct fitment on the Royal Enfield Bear 650. Model-specific geometry ensures correct coverage of the engine and lower frame zones, no interference with exhaust routing or suspension travel, proper alignment with factory mounting points, and no permanent modification to the chassis. Installation is direct bolt-on. Professional installation is recommended for correct torque and alignment. Key Features Designed specifically for Royal Enfield Bear 650 Mild steel construction for impact absorption and structural rigidity Protects engine sump, lower frame rails, and underbody components Black powder-coated finish — corrosion and debris resistant 47 x 23 x 18 cm dimensions for substantial underbody coverage Direct bolt-on installation — no chassis modification required Specifications Brand: Legundary | Material: Mild Steel | Finish: Black | Dimensions: 47 x 23 x 18 cm | Weight: 2.764 kg | Fitment: Royal Enfield Bear 650 | Installation: Direct bolt-on Warranty This product comes with a manufacturer warranty from Legundary Custom Builds against manufacturing defects. RawTorque does not provide additional warranty coverage beyond the manufacturer's policy. For complete details, refer to your Warranty Policy.

Read more less

Royal Enfield Bear 650 Gopher Luggage Carrier – Legundary Mild Steel Rear Carrier Product Description The Royal Enfield Bear 650 Gopher Luggage Carrier from Legundary is designed specifically for the Royal Enfield Bear 650. This rear carrier is built to provide a structured mounting platform for luggage during daily use and long-distance riding. Constructed from mild steel and finished in black, the carrier features a metal base plate designed to support mounted luggage. The structure allows riders to secure duffel bags, soft luggage, or mount a carrier plate for compatible top boxes. The layout is developed to align with the Royal Enfield Bear 650 frame geometry for proper fitment. The Royal Enfield Bear 650 Gopher Luggage Carrier measures 38 x 32 x 13 cm and has a listed weight of 1.74 kg. It is described as an easy-install component and can be removed when not required. The design focuses on providing a stable rear mounting surface for luggage. For riders seeking a dedicated rear luggage mounting solution for the Royal Enfield Bear 650, this Legundary Gopher Luggage Carrier provides a model-specific mild steel platform. Specifications Brand: Legundary Product Type: Luggage Carrier Motorcycle Compatibility: Royal Enfield Bear 650 Material: Mild Steel Finish: Black Dimensions: 38 x 32 x 13 cm Weight: 1.74 kg Installation: Easy Installation

Read more less

Royal Enfield Bear 650 Thanos Crash Guard with Slider – Legundary Mild Steel Product Description The Royal Enfield Bear 650 Thanos Crash Guard with Slider from Legundary is designed specifically for the Royal Enfield Bear 650. This crash guard setup includes integrated sliders and is built to provide structural protection around the engine and lower section of the motorcycle. Constructed from mild steel and finished in black, the guard follows a model-specific layout intended to align with the Royal Enfield Bear 650 chassis. The integrated sliders extend outward from the guard structure and are positioned to create separation between key components and the ground surface during impact scenarios. The Royal Enfield Bear 650 Thanos Crash Guard with Slider measures 63 x 42 x 51 cm and has a listed weight of 4.23 kg. It is described as an easy-install component engineered to integrate with the motorcycle’s frame structure. For riders seeking a dedicated crash protection solution for the Royal Enfield Bear 650, this Legundary Thanos Crash Guard with Slider provides a direct-fit mild steel setup with integrated side sliders. Specifications Brand: Legundary Product Type: Crash Guard with Slider Motorcycle Compatibility: Royal Enfield Bear 650 Material: Mild Steel Finish: Black Dimensions: 63 x 42 x 51 cm Weight: 4.23 kg Installation: Easy Installation

Read more less

Moto Torque Air Filter for Royal Enfield Interceptor 650, Continental GT 650 & Bear 650 The Moto Torque Performance Air Filter is precision-built for Royal Enfield Interceptor 650, Continental GT 650, and Bear 650 motorcycles. Designed for twin-cylinder performance platforms, this air filter enhances intake airflow while maintaining filtration integrity for consistent engine performance. Engineered to meet the demands of Royal Enfield 650cc motorcycles, the filter supports improved combustion efficiency, throttle response, and long-term riding performance across city, highway, and touring conditions. Designed for Royal Enfield 650 Platform • Royal Enfield Interceptor 650• Royal Enfield Continental GT 650• Royal Enfield Bear 650• Twin-cylinder 650 engine compatibility Model-specific fitment ensures structural precision and consistent sealing within the airbox. Engineered Features 4-Layer High-Flow Cotton GauzeConstructed with four layers of precision-woven cotton gauze to improve intake flow while maintaining filtration integrity. Supports optimized combustion and sustained power output. Multi-Stage Filtration EfficiencyCaptures fine dust, debris, and airborne contaminants without restricting airflow. Designed for varied riding environments including urban traffic and open highways. Reusable & Serviceable DesignBuilt for longevity and sustainability. The filter can be cleaned, re-oiled, and reused — reducing replacement frequency and maintenance costs. Heat-Resistant & Structurally ReinforcedEngineered to withstand elevated temperatures and vibration stress typical of twin-cylinder engines. Enhanced Throttle Response & Engine EfficiencyBy reducing intake resistance, the filter promotes smoother throttle input, cleaner combustion, and improved fuel efficiency. Performance Profile by Motorcycle Royal Enfield Interceptor 650Supports smoother torque delivery and consistent cruising performance. Royal Enfield Continental GT 650Designed to complement aggressive acceleration and high-rev responsiveness. Royal Enfield Bear 650Reinforces airflow stability and engine endurance for long-haul touring. Specifications • Brand: Moto Torque• Product Type: Performance Air Filter• Compatibility: Interceptor 650 / Continental GT 650 / Bear 650• Construction: 4-Layer Cotton Gauze• Design: Reusable & Serviceable• Engine Type: Twin-Cylinder 650cc

Read more less

The Red Rooster Stellar X Performance Exhaust is a motorcycle exhaust system developed specifically for the Royal Enfield Bear 650. It is designed for riders looking to upgrade the stock exhaust with a deeper and more engaging exhaust note while retaining controlled sound levels suitable for daily riding and long-distance touring. The Stellar X is positioned as a balanced performance exhaust rather than an extreme loud setup. It focuses on improving the riding experience through sound character, weight reduction, and efficient exhaust flow without compromising usability for regular road use. Design and Construction The Red Rooster Stellar X exhaust is manufactured using SS304 stainless steel, chosen for its strength, corrosion resistance, and thermal stability under sustained riding conditions. Stainless steel construction helps the exhaust withstand heat cycles and environmental exposure over time, making it suitable for both urban riding and extended highway use. The exhaust design prioritizes structural integrity while keeping overall weight lower than the stock exhaust system. Reduced weight contributes to improved handling feel and easier maneuverability, especially during city riding and low-speed conditions. Performance Characteristics The Stellar X exhaust is engineered to support freer engine breathing compared to the stock exhaust. By reducing exhaust restriction, it supports smoother exhaust flow, which can contribute to improved throttle response during acceleration and roll-on riding scenarios. Rather than focusing on maximum loudness, Red Rooster positions the Stellar X as an exhaust that delivers a deeper and more aggressive exhaust tone while maintaining sound levels that remain practical for everyday use. This makes it suitable for riders who want a noticeable sound upgrade without excessive noise fatigue on longer rides. No ECU remapping or engine modifications are stated as required by the manufacturer for installation or operation. Fitment and Installation The Red Rooster Stellar X Performance Exhaust is supplied as a bolt-on replacement for the Royal Enfield Bear 650. It is designed to mount directly onto the motorcycle using existing mounting points, without the need for permanent modifications to the bike. Installation does not require cutting, welding, or alteration of the motorcycle frame. Fitment compatibility is specific to the Bear 650, and proper installation ensures correct alignment and secure mounting. Professional installation is recommended to ensure proper fitment and to avoid exhaust leaks or alignment issues. Riding Usage This exhaust system is suited for: Daily city commuting Highway riding Long-distance touring Its balanced sound profile and stainless steel construction make it suitable for riders who want a functional upgrade that integrates well with regular riding conditions rather than track-only use. Finish Options The Red Rooster Stellar X exhaust is offered in multiple finish options, which can be selected as variants during purchase. Finish availability may vary depending on stock and manufacturer supply. What’s Included 1 x Red Rooster Stellar X Performance Exhaust for Royal Enfield Bear 650 Required mounting components as supplied by the manufacturer Important Notes Designed specifically for Royal Enfield Bear 650 This is a performance exhaust system, not a cosmetic slip-on only No ECU remapping or engine changes are stated as required by the manufacturer Installation quality directly affects performance and sound output Summary The Red Rooster Stellar X Performance Exhaust for Royal Enfield Bear 650 is a well-balanced exhaust upgrade designed for riders who want improved sound character, reduced weight, and practical performance benefits without sacrificing everyday usability. Built using SS304 stainless steel and supplied as a direct bolt-on system, it offers a clean and reliable upgrade path for Bear 650 owners.Usage and Maintenance The Red Rooster Stellar X Performance Exhaust for Royal Enfield Bear 650 is intended for regular road use under normal riding conditions. Periodic inspection of mounting points and fasteners is recommended to ensure secure fitment over time. Exhaust sound and performance characteristics may vary depending on riding style and operating conditions.

Read more less

BMC FM01070 High-Performance Air Filter for Royal Enfield Interceptor 650, Continental GT 650 & Bear 650 The BMC High-Performance Air Filter is engineered for riders who demand measurable performance gains. It is designed specifically for the Royal Enfield Interceptor 650, Continental GT 650, and Bear 650. This is not a cosmetic upgrade. It is a functional airflow improvement. The BMC Air Filter replaces the restrictive stock paper filter with a high-flow cotton gauze system. It maintains superior filtration while allowing more consistent airflow. That balance is what improves throttle feel without compromising engine safety. BMC uses its patented Full Moulding Technology to manufacture this filter. The structure is produced as a single seamless piece. There are no welded joints. There are no weak bonding areas. This ensures structural integrity under heat and vibration. The filtration medium is multi-layer cotton gauze. It is soaked in low-viscosity oil. This oil traps fine particles without blocking airflow. The cotton gauze is protected by an epoxy-coated alloy mesh. This mesh provides shape retention and durability. Filtration efficiency goes down to 7 microns. Most OEM paper filters stop at approximately 10 microns. That difference matters in dusty riding environments. Indian road conditions demand better filtration. The BMC High-Performance Air Filter improves airflow consistency. That translates into sharper throttle response. Roll-ons feel cleaner. Mid-range pull feels smoother. The engine breathes with less restriction. Unlike disposable paper filters, this BMC Air Filter is washable and reusable. It is designed to last the lifetime of the motorcycle when maintained properly. With periodic cleaning and re-oiling, performance remains consistent. Paper filters degrade over time. Airflow reduces as the material loads with dust. Throttle response gradually becomes dull. Riders often do not notice this performance drop. The BMC High-Performance Air Filter maintains its flow characteristics for significantly longer intervals. The benefit is not only performance. It is also cost efficiency. One reusable filter replaces multiple paper elements over the years. That reduces long-term ownership costs. Installation is straightforward. The BMC Air Filter matches OEM dimensions. It drops directly into the factory airbox. No modification is required. No tuning is required for standard road use. The Royal Enfield Interceptor 650 benefits from improved throttle clarity. The Continental GT 650 gains cleaner mid-range response. The Bear 650, with its newer platform, maintains optimal airflow balance with this filter. This is a performance upgrade designed for real riding. It supports highway cruising. It supports city commuting. It supports long-distance touring. The airflow improvement remains stable under sustained engine load. Heat resistance is another advantage. Cotton gauze and alloy mesh construction withstand higher temperatures than standard paper filters. Structural deformation is significantly reduced. The BMC High-Performance Air Filter is pre-oiled from the factory. It is ready to install out of the box. No preparation is required before fitment. For riders who prefer measurable upgrades, airflow efficiency matters. Combustion improves when airflow improves. Improved combustion can lead to smoother power delivery. That is what riders experience as better throttle response. This filter does not create exaggerated noise. It does not alter exhaust tone dramatically. It enhances engine breathing efficiency. That is the primary function. Consistency defines this upgrade. The engine receives steady airflow across the rev range. Low-end response feels clean. Mid-range pull feels linear. High-rev breathing remains stable. The BMC Air Filter is manufactured in Italy. Quality control standards are strict. Material selection is performance-oriented. This product is compatible with: Royal Enfield Interceptor 650 – 2019 onwards Royal Enfield Continental GT 650 – 2019 onwards Royal Enfield Bear 650 – 2024 onwards Compatibility is based on shared airbox architecture. Maintenance is simple. Use the official BMC cleaning kit. Wash the filter. Allow it to dry completely. Re-oil lightly. Reinstall. This process restores filtration efficiency and airflow performance. Riders who tour long distances benefit from durability. Riders who commute daily benefit from consistent throttle feel. Riders who ride in dusty regions benefit from improved filtration. This is a precision airflow component. It is engineered, not improvised. The BMC High-Performance Air Filter is built to perform reliably across thousands of kilometres. If your goal is cleaner combustion, improved throttle precision, and long-term durability, this upgrade delivers measurable value. Ride cleaner. Ride stronger. Ride with controlled airflow.

Read more less

The PowerTRONIC V4 Performance ECU is an advanced plug-and-play piggyback engine control module designed specifically for Royal Enfield motorcycles. It is engineered for riders who want sharper throttle response, improved torque delivery, smoother acceleration, and refined fueling control — without permanently modifying the stock ECU. Unlike generic tuning devices, the PowerTRONIC V4 ECU works by intelligently adjusting fueling and ignition parameters in real time. It connects directly to your motorcycle’s stock wiring harness, allowing seamless integration without cutting wires or flashing the factory ECU. This means performance gains remain reversible while maintaining factory reliability standards. Advanced Fueling & Ignition Control The PowerTRONIC V4 Performance ECU for Royal Enfield continuously monitors engine inputs and optimizes the air-fuel ratio for improved combustion efficiency. By refining fueling delivery and ignition timing, the module enhances throttle crispness and mid-range pull — two areas where most riders immediately notice improvement. This results in: • Smoother acceleration across RPM range• Reduced throttle lag• Improved ride refinement in traffic and touring conditions• Stronger roll-on performance during overtakes Because Royal Enfield engines respond well to optimized fueling, the V4 ECU delivers noticeable improvements without compromising long-term durability. Dual Pre-Tuned Maps & Adaptive Capability The PowerTRONIC V4 ECU comes with dual pre-configured performance maps developed specifically for Royal Enfield platforms. Riders can switch between maps depending on riding conditions or modifications such as aftermarket exhaust systems. The module also supports advanced tuning access through compatible software. This allows experienced users to fine-tune fueling parameters for specific setups, altitudes, or riding styles. For most users, however, the pre-loaded maps deliver significant improvement right out of the box. True Plug & Play Installation Installation is completely plug-and-play. The PowerTRONIC V4 Performance ECU connects to the stock harness using model-specific connectors. No ECU flashing, no soldering, and no dyno session is mandatory for baseline operation. Once installed: • The module automatically begins adaptive fueling• Factory ECU remains untouched• No permanent changes are made to the motorcycle This makes the V4 a practical upgrade for riders who want performance without invasive modification. Built for Real-World Riding Constructed using automotive-grade electronics, the PowerTRONIC V4 ECU is heat-resistant, vibration-resistant, and weather-protected for Indian riding conditions. Whether you ride through city congestion, long-distance highways, or varying altitude zones, the system adapts to maintain consistent performance. The result is improved throttle smoothness during daily commuting, stronger mid-range during highway cruising, and enhanced rideability during touring. Performance Without Compromise The goal of the PowerTRONIC V4 Performance ECU for Royal Enfield motorcycles is not extreme racing output. It is controlled, refined, usable performance. Riders typically report: • More responsive throttle feel• Smoother engine character• Cleaner acceleration• Reduced jerkiness at low RPM Because the stock ECU remains active, factory safety parameters continue functioning as intended. Compatibility (Variant Selection Required) The PowerTRONIC V4 ECU is available for the following Royal Enfield models: • Royal Enfield Himalayan 411 EFI (2020–2023)• Royal Enfield Himalayan 450 (2024–2025)• Royal Enfield Interceptor 650• Royal Enfield Continental GT 650• Royal Enfield Classic 350 (J-Series)• Royal Enfield Meteor 350• Royal Enfield Hunter 350 Select the correct motorcycle variant before purchase to ensure proper fitment. Technical Overview Brand: PowerTRONICProduct Type: Performance Piggyback ECUInstallation Type: Plug & PlayMaps: Dual Pre-Tuned MapsFueling Control: Real-Time Adaptive AdjustmentApplication: Royal Enfield MotorcyclesWarranty: As per official PowerTRONIC manufacturer policy What’s Included • PowerTRONIC V4 Performance ECU Module• Model-Specific Wiring Harness• Mounting Accessories (as provided by manufacturer) No additional hardware is assumed unless shown in product images.

Read more less